Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope

Einführung

This manual provides essential information for the safe and efficient operation of your Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope. This instrument is designed for precise measurement and analysis of electronic signals, featuring a 100 MHz bandwidth and 2 analog channels.

Zu den Hauptmerkmalen gehören:

• Analog input channels: 2 inputs
• Bandbreite: 100 MHz
• Sample rate: 2.5 GS/s Half channels; 1.25 GS/s All channels
• Record length: 10 Mpoints per channel
• Vertical resolution: 8 bits ADC; Up to 16 bits in high-resolution mode

Einrichtung und Anschlüsse

Before operating the oscilloscope, ensure it is placed on a stable, level surface with adequate ventilation. Connect the power cord to the instrument and a grounded AC outlet.

Figure 1: Front panel of the Tektronix MSO22 2-BW-100 Oscilloscope, showing the display, control knobs, buttons, and input connectors (Inputs 1, 2, Aux In, AFG/Aux Out).

Eingangsanschlüsse

• Analog Inputs (1, 2): Connect your probes to these BNC connectors for signal acquisition.
• Aux-Eingang: Auxiliary input for external trigger or other signals.
• AFG/Aux Out: Output for the Arbitrary Function Generator or auxiliary signals.

Einschalten

Press the power button located on the front panel to turn on the instrument. Allow a few moments for the system to boot up.

Bedienungsanleitung

This section outlines the basic steps for operating the oscilloscope to capture and analyze waveforms.

Basic Waveform Capture

1. Sonde anschließen: Attach a compensated probe to one of the analog input channels (e.g., Input 1).
2. Anschluss an den Schaltkreis: Connect the probe tip to the test point in your circuit and the ground clip to the circuit's ground.
3. Automatische Einstellung: Drücken Sie die Auto-Set button (if available, common on oscilloscopes) to automatically adjust vertical and horizontal settings for a stable display.
4. Vertikale Skala anpassen: Verwenden Sie die Vertikale Skalierung knob to adjust the volts per division, controlling the amplitude of the waveform on the screen.
5. Horizontale Skala anpassen: Verwenden Sie die Horizontale Skalierung knob to adjust the seconds per division, controlling the time base of the waveform.
6. Trigger einstellen: Verwenden Sie die Trigger-Level Drehknopf zum Einstellen der Lautstärketage level at which the oscilloscope captures the waveform, ensuring a stable display.

Messfunktionen

The MSO22 2-BW-100 offers various automated measurement functions. Access these through the on-screen menu system. Common measurements include Peak-to-Peak Voltage, Frequency, Period, and Rise/Fall Time.

Wartung

Durch sachgemäße Wartung werden die Langlebigkeit und Genauigkeit Ihres Oszilloskops gewährleistet.

Reinigung

• Wischen Sie die Außenflächen mit einem weichen, damp Tuch. Keine Scheuer- oder Lösungsmittel verwenden.
• Stellen Sie sicher, dass keine Flüssigkeit in das Instrument gelangt.
• Clean the display screen with a soft, lint-free cloth specifically designed for electronic displays.

Kalibrierung

For optimal performance, periodic calibration by qualified service personnel is recommended. Refer to the official Tektronix service manual for calibration procedures and intervals.

Fehlerbehebung

Dieser Abschnitt bietet Lösungen für häufig auftretende Probleme.

• Kein Bildschirm:
  • Ensure the power cord is securely connected and the instrument is powered on.
  • Check the brightness and contrast settings of the display.
• Instabile Wellenform:
  • Adjust the trigger level and trigger source settings.
  • Verify the probe compensation is correct.
  • Check for proper grounding of the probe and the circuit under test.
• Kein Signal empfangen:
  • Ensure the probe is correctly connected to the input channel and the circuit.
  • Check the input coupling (AC/DC/GND) and vertical scale settings.
  • Verify the signal source is active.

If problems persist, contact Tektronix customer support.

Technische Daten

Detailed technical specifications for the Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope.

Garantie und Support

Tektronix products are designed for reliability and performance. For information regarding product warranty, please refer to the warranty statement included with your purchase or visit the official Tektronix webWebsite.

For technical support, service, or additional documentation, please contact Tektronix customer service or visit their official support portal. Ensure you have your product model number (MSO22 2-BW-100) and serial number ready when contacting support.

Online-Ressourcen: www.tek.com