Scharfer SPC736

SHARP Dual-Wecker Bedienungsanleitung

Modell: SPC736

1. Produktüberschreitungview

The SHARP SPC736 Dual Alarm Clock features a jumbo 1.8-inch white LED display with a faux wood finish, designed for clear visibility and a modern aesthetic. It includes dual alarm settings, a 3-step dimmer control for adjustable brightness, and a battery backup system to maintain time and alarm settings during power outages.

SHARP SPC736 Dual Alarm Clock with 1.8-inch white LED display and faux wood finish, showing time 12:08 PM.

Bild: Vorderseite view of the SHARP SPC736 Dual Alarm Clock, displaying 12:08 PM. The clock features a large white LED display set against a faux wood grain panel, with control buttons visible on the top edge.

2. Einrichtung

2.1 Stromversorgung des Geräts

The SHARP SPC736 alarm clock operates primarily on AC power. Connect the provided AC adapter to the clock and plug it into a standard electrical outlet.

2.2 Installation der Notstromversorgung

For battery backup functionality, install 2 x AAA batteries (not included) into the battery compartment located on the bottom of the unit. The battery backup ensures that time and alarm settings are retained during a power interruption, though the display will not illuminate.

2.3 Anfangszeiteinstellung

  1. Halten Sie die ZEITEINSTELLUNG button (usually indicated by a clock icon) until the display flashes.
  2. Verwenden Sie die HR (Stunde) und MIN (Minute) buttons to adjust the time. Pay attention to the PM indicator for correct AM/PM setting.
  3. Drücken Sie die ZEITEINSTELLUNG Zum Bestätigen und Verlassen des Zeiteinstellungsmodus erneut drücken.

3. Bedienungsanleitung

3.1 Alarme einstellen (Alarm 1 und Alarm 2)

This clock features two independent alarms. Follow these steps for each alarm:

  1. Halten Sie die ALARM 1 or ALARM 2 button (indicated by a bell icon) until the alarm time flashes.
  2. Verwenden Sie die HR Und MIN buttons to set the desired alarm time. Ensure the AM/PM indicator is correct.
  3. Drücken Sie die entsprechende Taste ALARM button again to confirm the setting. The alarm indicator will appear on the display.
  4. Zum Aktivieren/Deaktivieren eines Alarms drücken Sie die Taste ALARM 1 or ALARM 2 button briefly. The alarm indicator will turn on or off.

3.2 Schlummerfunktion

Wenn ein Alarm ertönt, drücken Sie die große Taste. SCHLAFEN Der Knopf befindet sich oben auf der Uhr. Der Alarm wird kurzzeitig unterbrochen und ertönt nach etwa 9 Minuten erneut.

3.3 Dimmersteuerung

The clock features a 3-step dimmer control to adjust the brightness of the LED display. Repeatedly press the DIMMER button (indicated by a sun icon) to cycle through high, medium, low, and off brightness settings.

4. Wartung

4.1 Reinigung

To clean the clock, gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the finish or display.

4.2 Batteriewechsel

Wenn die Uhr häufig Stromausfälle erleidettages or if the display does not retain time during brief disconnections, it may be time to replace the AAA backup batteries. Ensure the clock is connected to AC power before replacing batteries to avoid losing current time settings.

5. Fehlerbehebung

ProblemMögliche UrsacheLösung
Anzeige ist leer.No AC power; Dimmer set to 'off'.Ensure AC adapter is securely plugged in. Press the DIMMER button to cycle through brightness settings.
Der Alarm ertönt nicht.Alarm not activated; Alarm volume too low (if applicable); Incorrect alarm time set.Verify alarm indicator is on. Check alarm time for AM/PM accuracy.
LED segments are dim or missing.LED component degradation over time.This may indicate a component failure. If within warranty, contact customer support. Otherwise, replacement may be necessary.
Zeit/Einstellungen nach Stromausfall verlorentage.Die Notstrombatterien sind defekt oder nicht installiert.Install new 2 x AAA batteries in the battery compartment.

6. Spezifikationen

  • Marke: Scharf
  • Modell: SPC736
  • Anzeigetyp: Digitale LED
  • Anzeigegröße: 1.8 Zoll (Jumbo)
  • Anzeigefarbe: Weiß
  • Beenden: Kunstholz
  • Energiequelle: AC Powered with 2 x AAA Battery Backup (batteries not included)
  • Besondere Merkmale: Dual Alarms, 3-Step Dimmer Control, Snooze Function
  • Abmessungen: Ungefähr 8 x 5.6 x 3 Zoll
  • Gewicht: Ungefähr 12.8 Unzen
  • UPC: 049353000275

7. Garantie und Support

For detailed warranty information and customer support, please refer to the documentation included with your product at the time of purchase or visit the official Sharp website. This manual provides general operational guidelines and does not supersede specific warranty terms.

Note: No official seller videos were available for embedding based on the provided data. For additional product demonstrations or support, please check the manufacturer's official channels.

Zugehörige Dokumente - SPC736

Vorview Sharp SPC276 Digitaler Wecker mit Bluetooth und Schlafgeräuschen: Benutzerhandbuch
Ausführliche Anleitung zur Bedienung des digitalen Weckers Sharp SPC276, einschließlich Funktionen, Einrichtung, Weckfunktionen, Bluetooth-Konnektivität, Schlafgeräusche und Sicherheitsvorkehrungen.
Vorview Anleitung zum Austausch der Rückseite des Sharp Aquos Serie mini SHV31
Detaillierte Schritt-für-Schritt-Anleitung zum Austauschen der Rückseite des Sharp Aquos Serie mini SHV31 Smartphones. Diese Anleitung enthält eine Liste der benötigten Werkzeuge sowie klare Anweisungen für die Demontage und Montage.
Vorview Anleitung zum Austausch der Gehäuserückseite des Sharp Aquos LC13B2UA
Eine Schritt-für-Schritt-Anleitung zum Austausch der Rückwand des Sharp Aquos LC13B2UA LCD-Fernsehers, inklusive Werkzeug und Anweisungen.
Vorview SHARP SPC543 Projektionswecker mit USB-Anschluss - Bedienungsanleitung
Offizielle Bedienungsanleitung und Garantieinformationen für den SHARP SPC543 Projektionswecker mit USB-Anschluss. Erfahren Sie, wie Sie Uhrzeit, Wecker und Datum einstellen, die Projektionsfunktion nutzen und die Sicherheitshinweise verstehen.
Vorview Anleitung zum Austausch der Rückwand des Sharp Aquos Crystal
Eine Schritt-für-Schritt-Anleitung von iFixit zum Austausch der Rückseite eines Sharp Aquos Crystal Smartphones. Diese Anleitung konzentriert sich auf die notwendigen Schritte, um die Rückseite zu öffnen.
Vorview Sharp SPC182 LED-Wecker mit USB-Anschluss – Bedienungsanleitung und Garantie
Offizielle Bedienungsanleitung und Garantieinformationen für den Sharp SPC182 LED-Wecker mit USB-Anschluss. Erfahren Sie mehr über Funktionen, Einrichtung, Bedienung, Sicherheitshinweise und Kundensupport.