1. Einleitung
The NICREW ClassicLED Plus LED Aquarium Light is designed to provide optimal lighting for freshwater or saltwater fish and low-to-medium light level aquatic plants. This full-spectrum light combines 6500K white, 450nm blue, TRUE 660nm deep red, and green LEDs to produce a fine-tuned color spectrum. It features a programmable timer with adjustable auto On/Off times, brightness, and ramp-up/dim-down periods to simulate natural sunrise and sunset cycles.
2. Sicherheitshinweise
- Always unplug the fixture from the power outlet before performing any maintenance or cleaning.
- This product is designed for indoor use only. Do not immerse the light fixture in water.
- Ensure the power cord is not damaged. If damaged, do not operate the fixture.
- Außerhalb der Reichweite von Kindern aufbewahren.
- Do not operate if any part of the fixture is wet. Dry thoroughly before plugging in.
- Ensure the light is securely mounted on the aquarium to prevent accidental falls into the water.
3. Packungsinhalt
Prüfen Sie, ob alle Artikel vorhanden und in gutem Zustand sind:
- NICREW ClassicLED Plus LED Aquarium Light Fixture
- Wired Controller with Timer
- Adjustable Mounting Brackets (2x)
- Netzteil
4. Einrichtung und Installation
- Packen Sie das Licht aus: Nehmen Sie die Leuchte und alle Komponenten vorsichtig aus der Verpackung.
Figure 1: NICREW ClassicLED Plus LED Aquarium Light fixture. This image shows the main light fixture with its array of white, blue, red, and green LEDs, and the extendable mounting brackets attached.
- Montagehalterungen anbringen: Slide the adjustable docking mounts onto both ends of the light fixture. These brackets allow for easy adaptation to fit most rimless and framed aquariums.
Figure 2: Close-up of the light showing the extendable mounting bracket and enhanced heat sink design. The image highlights the extendable mounting bracket for flexible installation and the enhanced heat sink design for better heat dissipation.
- Positionieren Sie das Licht: Place the light fixture securely on top of your aquarium. Adjust the extendable brackets to ensure a stable fit across the tank's width.
Figure 3: Dimensions and aquarium fitment guide. This diagram illustrates the various sizes available for the ClassicLED Plus and their corresponding dimensions, ensuring proper fitment for tanks ranging from 12 to 54 inches.
- Strom anschließen: Plug the wired controller into the light fixture, then connect the power adapter to the controller and finally to a power outlet.
5. Bedienungsanleitung
The NICREW ClassicLED Plus features a wired controller for programming the light cycle and adjusting settings. The light offers two independent channels: Channel 1 (CH1) for White, Red, and Green LEDs, and Channel 2 (CH2) for Blue LEDs.
5.1. Controller vorbeiview
This image demonstrates the independent control of Channel 1 (White, Red, Green LEDs) and Channel 2 (Blue LEDs), with brightness adjustable from 0% to 100%. Note that manual mode brightness is fixed at 100%.
5.2. Einstellen des Timers
The controller allows you to set a 24-hour light cycle with customizable on/off times, brightness levels, and ramp-up/dim-down periods for both channels. If you are changing pre-programmed settings, ensure the fixture is not left idle too long, or you may need to restart the process.
- Drücken Sie die SATZ button to enter programming mode. The display will show "00:00" and flash.
- Verwenden Sie die STUNDE Und MINUTE Tasten, um die aktuelle Uhrzeit einzustellen.
- Drücken SATZ again. The display will show "ON" briefly, then flash the current time. Use STUNDE Und MINUTE to set the desired ON time for Channel 1 (White, Red, Green LEDs).
- Drücken SATZ. The display will show "OFF" briefly, then flash the current time. Use STUNDE Und MINUTE to set the desired OFF time for Channel 1.
- Drücken SATZ. The display will show "100" briefly. Use STUNDE (+) und MINUTE (-) to set the brightness percentage (0-100%) for Channel 1.
- Repeat steps c-e for Channel 2 (Blue LEDs).
- Drücken SATZ. The display will flash the current ramp time mode (00, 15, or 30). Use STUNDE (+) bzw MINUTE (-) to choose between 00 (straight on/off), 15 (15-minute ramp-up/dim-down), or 30 (30-minute ramp-up/dim-down).
- Drücken SATZ to save and exit the settings.
This graph visually represents a typical 24-hour light cycle, showing how Channel 1 (White, Red, Green LEDs) and Channel 2 (Blue LEDs) can be programmed with different on/off times, brightness levels, and ramp-up/dim-down periods to simulate natural lighting conditions.
5.3. Manueller Betrieb
To manually turn the light on or off, or switch between modes without using the timer, press the power button on the controller. In manual mode, the brightness is fixed at 100%.
5.4. Video Tutorial: Programming the Timer
This video provides a step-by-step guide on how to program the integrated timer on your NICREW ClassicLED Plus light, including setting the current time, on/off times for each channel, brightness, and ramp-up/dim-down durations.
6. Wartung
- Reinigung: Regularly wipe the light fixture with a soft, dry cloth to remove dust and water spots. Ensure the light is unplugged before cleaning. Do not use abrasive cleaners or solvents.
- LED-Oberfläche: Gently clean the LED surface with a damp Bei Bedarf mit einem Tuch abwischen. Die Oberfläche nicht zerkratzen.
- Power Cord and Connections: Periodically inspect the power cord and all connections for any signs of damage or wear. Replace if necessary.
7. Fehlerbehebung
| Problem | Mögliche Ursache | Lösung |
|---|---|---|
| Licht geht nicht an. | Power not connected, faulty outlet, damaged cable/fixture. | Check power connections. Test outlet with another device. Inspect cable for damage. Contact support if fixture is faulty. |
| Die Timer-Einstellungen gehen nach einem Stromausfall verloren.tage. | The internal clock resets on power loss, but programmed schedules are retained. | Manually reset the current time on the controller after a power outage. The light will then resume its programmed schedule. |
| Das Licht ist zu hell/zu dunkel. | Brightness settings are incorrect or in manual mode. | Adjust brightness levels in programming mode for timed cycles. Note that manual mode is fixed at 100% brightness. |
| Das Licht flackert oder blinkt. | Lose Verbindung, Stromschwankung, interner Fehler. | Check all connections. Ensure stable power supply. If problem persists, contact support. |
8. Spezifikationen
- Modell: N10372
- Wastage: 15 Watt
- Helligkeit: 850 Lumen
- Dimensions (Light Fixture): 17.52"L x 4.57"W x 2.52"H (for 18-24 inch tank)
- Material: Acrylic, Aluminum, Glass
- Lichtquellentyp: LED (6500K white, 450nm blue, TRUE 660nm deep red, green)
- Kontrollmethode: Wired Controller with Timer
- Energiequelle: Kabelgebunden (20V Gleichstrom)
- Wasserbeständigkeit: Not Water Resistant (Do not immerse)
9. Garantie und Support
NICREW products are designed for ease of use and enjoyment. This product comes with a hassle-free 12-month warranty. For any questions, concerns, or technical support, please contact NICREW customer service. We are dedicated to providing quality products and support to ensure a better fish keeping experience.
For further assistance, please visit the official NICREW Store: NICREW Store on Amazon
