eletechsup DDEN12MA+DDEN12MB DC-DC Boost Converter Module User Manual

1. Einleitung

This manual provides detailed instructions for the eletechsup DDEN12MA+DDEN12MB DC-DC Boost Converter Module. This module is designed to step up an input voltage from 2.6V-5.5V to a selectable fixed output voltage of 5V, 6V, 9V, or 12V. It features high efficiency and multiple protection mechanisms, making it suitable for various electronic applications.

2. Sicherheit und Warnungen

Wichtige Sicherheitshinweise:

• Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
• Keep the device and its cord out of reach of children under 3 years old.
• Keep away from children unless supervised by an adult.
• Verwenden Sie dieses Produkt nicht für andere als die vorgesehenen Zwecke.
• Inspect the product before each use; do not use if damaged.
• Nicht Wasser oder Feuchtigkeit aussetzen.
• Handle with care to avoid cuts or injuries (if applicable to sharp components).
• Follow installation and operation guidelines to avoid injury.

3. Produktmerkmale

• Typ: DC/DC Converter (Step-up Boost Module)
• Eingangslautstärketage: Gleichstrom 2.6 V - 5.5 V
• Ausgangsvolumentage Optionen: Selectable DC 5V, 6V, 9V, or 12V
• Ausgangsstrom: <1.3A (varies by output voltage, refer to specifications)
• Ausgangsleistung: 1 - 50 W
• Ausgabefrequenz: 1 MHz
• Effizienz: Up to 94% (typically 75%-91%)
• Ruhestrom: 210uA (output on), 5uA (output off)
• Betriebstemperatur: -40°C bis +85°C
• Lagertemperatur: -65°C bis +150°C
• Dimensions (without pins): 20 x 15 x 6 mm
• Gewicht: 1.8g (with pins), 1.5g (no pins)
• Schutzfunktionen:
  • Überstromschutz (OCP)
  • Über Voltage-Schutz (OVP)
  • Kurzschlussschutz (SCP)
  • Übertemperaturschutz (OTP)
• Enable Pin (En): Allows external control to turn output on/off.

4. Packungsinhalt

Ihr Paket sollte Folgendes enthalten:

• 1 PCS 6W DDEN12MB DC-DC Boost Converter Module (with your selected fixed output voltage)

Note: The module may come with or without pins, as selected during purchase.

5. Technische Daten

Performance Tables (Reference Only)

The following tables provide typical input/output current measurements for different output voltage variants. Actual performance may vary.

5V Output Performance

6V Output Performance

9V Output Performance

12V Output Performance

6. Einrichtung und Installation

The module has four main connection points: Input Positive (Vi), Ground (G), Output Enable (En), and Output Positive (Vo).

• Wie: Input positive (+) terminal. Connect your DC input voltage (2.6V - 5.5V) here.
• G: Ground (-) terminal. This is common for both input and output.
• De: Output Enable pin. This pin controls whether the output is active.
• Stimme: Output positive (+) terminal. The boosted DC output voltage (5V, 6V, 9V, or 12V) is available here.

Ausgangsvolumentage Auswahl

Das Ausgangsvolumentage of the module is selectable by bridging the corresponding pads on the back of the module. Ensure only one voltage pad is bridged at a time to set the desired output (5V, 6V, 9V, or 12V).

Enable Pin Operation

• To turn on the output: Connect the 'En' pin to Ground (GND).
• To turn off the output: Leave the 'En' pin not connected (floating) or connect it to the input voltage (Vi).
• The 'En' pin can also be controlled by a microcontroller (MCU): low level (GND) turns on output, high level (Vi or logic high) turns off output.

Schaltpläne

Application 1: With External Switch Control

In this configuration, an external switch is connected between the 'En' pin and Ground (GND). Closing the switch connects 'En' to GND, turning the output ON. Opening the switch disconnects 'En' from GND, turning the output OFF.

Application 2: No External Switch Required (Always ON)

For continuous operation where the output is always ON when input power is supplied, connect the 'En' pin directly to Ground (GND).

7. Bedienungsanleitung

1. Erstinspektion: Before connecting power, visually inspect the module for any damage. Ensure all protective films are removed.
2. Wählen Sie die Ausgangslautstärketage: If not pre-configured, bridge the appropriate pads on the back of the module for your desired output voltage (5 V, 6 V, 9 V oder 12 V).
3. Eingangsstromversorgung anschließen: Connect your DC power source (2.6V-5.5V) to the Vi (+) and G (-) terminals.
4. Control Output (if using 'En' pin):
   • To activate the output, ensure the 'En' pin is connected to GND.
   • To deactivate the output, ensure the 'En' pin is disconnected from GND (or connected to Vi).
5. Last anschließen: Connect your load to the Vo (+) and G (-) terminals. Ensure your load's voltage and current requirements do not exceed the module's maximum output capabilities for the selected output voltage.
6. Einschalten: Apply power to the input terminals. The module will boost the voltage to your selected fixed output.
7. Ausschalten und Lagerung: After use, disconnect the input power. If not in use, store the module in a dry place, away from children.

8. Wartung

• Keep the module clean and dry. Avoid exposure to dust, dirt, and liquids.
• Regularly inspect the module for any signs of physical damage, loose connections, or overheating.
• Do not attempt to repair the module yourself. Refer to qualified personnel for any issues.

9. Fehlerbehebung

Problem: Ausgangslautstärketage is lower than the nominal (expected) voltage.

Lösung: The input power supply might be too low or unable to provide sufficient current. Ensure your input power source can deliver the necessary voltage and current for the desired output. Check the input voltage with a multimeter; if it drops significantly under load, the input source is insufficient.

Problem: Keine Ausgangslautstärketage.

Lösung:

• Check input power connections (Vi and G).
• Überprüfen Sie die Eingabelautstärketage liegt im Bereich von 2.6 V – 5.5 V.
• Ensure the 'En' (Enable) pin is correctly connected to GND to turn on the output. If it's floating or connected to Vi, the output will be off.
• Check for short circuits on the output (Vo and G). The module has Short Circuit Protection (SCP) which might temporarily shut down the output.
• The module might be in Over Temperature Protection (OTP) if it has been operating under heavy load in a high ambient temperature. Allow it to cool down.

Problem: Module gets excessively hot.

Lösung:

• The output load might be too high, exceeding the module's maximum current/power rating. Reduce the load.
• Sorgen Sie für ausreichende Belüftung rund um das Modul.
• Verify that the input power is greater than the output power, accounting for the module's own power consumption.

Aufmerksamkeit:

• Eingangsvolumentage cannot be greater than the maximum input range (5.5V).
• Output power cannot be greater than the maximum load for a long time.
• Input power must be greater than the output power, due to the module's own power consumption.

10. Benutzertipps

• Ausgangsvolumentage Auswahl: The module's output voltage (5V, 6V, 9V, or 12V) is set by bridging specific pads on the back of the board. Make sure to select only one output voltage.
• Enable Pin Control: For applications requiring an ON/OFF function, a latching switch or a microcontroller is recommended for the 'En' pin to maintain the desired state. A momentary switch would only activate the output while pressed.
• Power Source Quality: Use a stable and adequately powered input source to avoid output voltage drops, especially under load.
• Audioanwendungen: While not explicitly designed for audio, some users have reported concerns about potential sound interference when used with Bluetooth portable speakers. If using in sensitive audio applications, test thoroughly.

11. Garantie und Support

Für technischen Support, Garantieansprüche oder weitere Anfragen wenden Sie sich bitte an den Hersteller:

Hersteller: Guangzhou Keshen Electronic Technology Co., Ltd

Kontakt: eletechsup@163.com

This product is manufactured in Mainland China. For detailed compliance information and regulations, please refer to the official product documentation. A comprehensive user manual in PDF format is available for reference: Benutzerhandbuch (PDF).