DapLok 2BGM6-TX11 Portable Locator Device
Overview introduction
FINDER integrates with Apple’s Find My network, providing a secure and user-friendly solution for tracking belongings. It effortlessly locates keys, wallets, and more using Apple Find My Network, prioritizing security. Designed for user convenience, FINDER simplifies daily life. Say goodbye to lost items with FINDER and Apple’s Find My network, experiencing a future of enhanced item tracking and peace of mind. Trust FINDER to redefine how you manage essentials effortlessly
Power On
Hold the button (approximately 25) and release until a single beep
heard, indicating the device is powering on.
Power Off
Hold the button until you hear a single beep, followed by two consecutive beeps, and then three continuous beeps. Release the button after hearing the continuous three beeps (approximately 6 seconds), indicating the device is powering off.
HOW TO PAIR
Note: iOS or macOS with the latest version.
- Place the FINDER next to your Apple device like an iPhone.
- Turn on Bluetooth on your iPhone and connect to the Internet.
- Press the finder side button, and hear one beep to power on.
- Open the ‘Find My’ app as shown in Figure 1
- In the ‘Find My’ app, click on Add Item – Other Support Items. As shown in Figure 2
- Click ‘Continue’. As shown in Figure 3
- Name your Finder and click ‘Continue’. As shown in Figure 4
- Select emoticons.
- Click ‘Continue’, then click ‘Finish’ to complete.
Battery
FINDER Contains a coin-shaped battery. During the product’s lifespan, it may be necessary to replace the battery. By observing the correct negative and positive connections, only replace batteries of the same type (CR2032) and rating.
Battery replacement
- Buckle open to open the battery cover (as shown in the figure);
- Replace the battery with a new one;
- Close the battery cover tightly.
ADDITIONAL TIPS
- To switch from active mode to Disable mode (Airplane mode), simply remove the battery.
- To switch from Disable mode (Airplane mode) to working mode, reinstall the battery. The FINDER will be successfully paired after this.
- Press and hold the button until you hear 1 prompt tone, followed by 2 consecutive prompt tones, and then 3 consecutive indicator tones. Continue to press for 5 seconds. When you hear a long indicator tone, release the button to restore the device to its factory settings..
- To remove the FINDER from your Apple devices, open the Find My app, select ‘items,’ find the device, and scroll down to click on ‘Remove this device.
- If the FINDER fails to connect to the Find My app, follow the instructions in section 3.3 to perform a factory reset, and then restart the pairing process.
The FINDER contains delicate electronic parts, including a battery. To avoid damage, loss of function, or potential harm, please refrain from dropping, hitting, puncturing, crushing, disassembling, exposing it to extreme heat or liquids, or placing it in areas with a high concentration of industrial chemicals.
WARNING: Do not swallow the battery; there is a chemical bum hazard
Choking Hazard Warning
The FINDER, its battery compartment door, the battery itself, and the case may pose a choking hazard or cause injury to small children. Please keep these items out of reach of young children
Medical Device Interference
The FINDER contains components and radios that emit electromagnetic fields, as well as magnets. These elements may potentially interfere with pacemakers, defibrillators, or other medical devices. To ensure safety, maintain a safe distance between your medical device and the FINDER. We strongly advise consulting your physician and the manufacturer of your medical device for information that is specific to your situation. If you suspect that the FINDER is interfering with your pacemaker, defibrillator, or any other medical device, discontinue its use immediately.It’s normal for the FINDER to show discoloration with regular use. To clean it, use a soft, dry, lint-free cloth. Avoid applying pressure with sharp objects on the rubber seal or the battery terminal contacts inside the device. Do not allow moisture to enter any openings or use aerosol sprays, solvents, or abrasive materials to clean the device.
Legal notice
Use of the Works with Apple badge means that a product has been designed to work specifically with the technology identified in the badge and has been certified by the product manufacturer to meet Apple Find My Network product specifications and requirements. Apple is not responsible for the operation of this device or use of this product or its compliance with safety and regulatory standards. Apple, Apple Find My, Apple Watch, Find My, iPhone, iPad, iPadOS, Mac, macOS and watchOS are trademarks of Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
Important matters
FCC Warnning
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. Suppose this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.
Specifications
- Compliance: Part 15 of FCC Rules
- Radiation Exposure Limits: FCC approved for uncontrolled environment
- Minimum Distance: 0cm between radiator and body
Product Usage Instructions
Installation
- Place the device on a stable surface.
- Ensure there is a minimum distance of 0cm between the radiator of the device and your body.
- Connect the device to a power source as per the provided instructions.
Operation
- Turn on the device using the designated power button.
- Follow the user manual for specific instructions on operating the device.
- Do not attempt to modify or change the device in any way that is not approved by the manufacturer.
Maintenance
- Clean the device regularly with a soft, dry cloth to prevent dust build-up.
- Avoid exposing the device to extreme temperatures or moisture.
- Keep the device away from direct sunlight to prevent damage.
Frequently Asked Questions (FAQ)
Q: Can I modify the device without voiding the warranty?
A: No, any modifications not explicitly approved by the manufacturer can void the warranty.
Q: What should I do if the device causes interference?
A: Ensure that the device is not causing harmful interference to other devices. If interference persists, contact customer support for assistance.
Documents / Resources
 |
DapLok 2BGM6-TX11 Portable Locator Device [pdf] User Manual 2BGM6-TX11 Portable Locator Device, 2BGM6-TX11, Portable Locator Device, Locator Device, Device |