JBL Stage 2 200P aktiv subwoofer brugermanual

1. Introduktion

JBL Stage 2 200P is a 300W powered subwoofer designed to enhance the low-frequency performance of your home audio system. Engineered at JBL's Acoustic Engineering Center of Excellence in Northridge, California, this subwoofer is part of the Stage series, delivering deep and powerful bass. It features a front-firing 10-inch (250mm) Polycellulose low-frequency woofer and dual rear-firing tuned ports for optimal bass response. A comprehensive set of controls allows for seamless integration into various audio setups.

2. Nøglefunktioner

• 10-tommer (250 mm) ribbet konisk lavfrekvenswoofer af polycellulose: Delivers robust and accurate bass.
• 150W RMS (300W dynamisk) Amplivligere: Giver ample power for dynamic low-frequency reproduction.
• Dobbelte bagudrettede tunede porte: Enhances bass output and extension.
• Delefilter, niveau og fasekontrol: Allows for precise adjustment and integration with main speakers.

3. Pakkens indhold

Sørg for, at alle varer er til stede ved udpakning:

• JBL Stage 2 200P Powered Subwoofer
• Strømledning
• Brugervejledning (dette dokument)

4. Opsætning

4.1. Placering

The placement of your subwoofer significantly impacts its performance. Experiment with different locations to find the best bass response in your listening area. Generally, placing the subwoofer in a corner can enhance bass output, while placing it along a wall can provide a more balanced sound. Avoid placing it directly against a wall or in a cabinet without proper ventilation.

Figur 1: Forside view af JBL Stage 2 200P Subwoofer. This image shows the subwoofer's front grille, which can be removed to reveal the woofer cone.

Figur 2: Forside view af JBL Stage 2 200P Subwoofer with the grille removed, highlighting the 10-inch Polycellulose ribbed cone woofer.

4.2. Forbindelser

Tilslut subwooferen til din lydmodtager eller amplifier using an LFE (Low-Frequency Effects) output or stereo RCA outputs. For optimal performance, use a dedicated subwoofer output from your receiver.

1. LFE-input: If your receiver has an LFE output, connect a single RCA cable from the receiver's LFE output to the subwoofer's LFE input.
2. Line-Level Inputs: If your receiver does not have an LFE output, connect RCA cables from the receiver's stereo pre-out (left and right) to the subwoofer's Line-Level inputs.

Figur 3: Bagside view af JBL Stage 2 200P Subwoofer, displaying the control panel, input/output connections, and dual rear-firing tuned ports.

Figur 4: Detaljeret view of the rear control panel, illustrating the Crossover, Volume, Phase, and Power Mode settings for system integration.

4.3. Strømtilslutning

Once audio connections are made, connect the supplied power cord to the subwoofer's power input and then to a suitable AC wall outlet. The subwoofer features a power mode switch (On/Auto/Normal/Reverse) for convenient operation.

5. Betjening

5.1. Kontroller overview

The rear panel of the JBL Stage 2 200P subwoofer provides several controls for fine-tuning its performance:

• Lydstyrke (niveau) kontrol: Justerer subwooferens samlede udgangsniveau. Start med en lav indstilling og øg gradvist, indtil bassen blandes problemfrit med dine hovedhøjttalere.
• Crossover kontrol: Sets the upper frequency limit for the subwoofer. Frequencies above this setting will be sent to your main speakers. Adjust this to match the low-frequency capabilities of your main speakers. A common starting point is 80 Hz.
• Fasekontrol (0°/180°): Adjusts the phase of the subwoofer's output relative to your main speakers. Experiment with both settings to find the one that provides the most impactful and coherent bass.
• Power Mode Switch (On/Auto/Normal/Reverse):
  • På: Subwooferen forbliver tændt konstant.
  • Auto: Subwooferen tænder automatisk, når der registreres et lydsignal, og går i standbytilstand efter en periode med inaktivitet.
  • Normal/Reverse: These settings might refer to specific phase adjustments or power-saving modes. Refer to the detailed manual for specific model functionality.

5.2. Initial Adjustment

1. Indstil Bind control to its minimum position.
2. Indstil Crossover control to approximately 80 Hz, or as recommended by your main speaker manufacturer.
3. Indstil Fase switch to 0°.
4. Indstil Strømtilstand to "Auto" for convenience.
5. Play some audio with significant bass content.
6. Øg gradvist Bind control until the bass output is balanced with your main speakers.
7. Eksperimenter med Fase switch (0° vs. 180°) to determine which setting provides the most natural and impactful bass in your listening position.
8. Further fine-tune the Crossover og Bind controls to achieve optimal integration and desired bass response.

6. Vedligeholdelse

• Rensning: Use a soft, dry cloth to clean the subwoofer cabinet. Avoid using abrasive cleaners, waxes, or solvents.
• Ventilation: Ensure adequate ventilation around the subwoofer to prevent overheating. Do not block the rear ports or place the unit in an enclosed space without airflow.
• Håndtering: When moving the subwoofer, lift it carefully from the base. Avoid dropping or subjecting it to strong impacts.

7. Fejlfinding

8. Specifikationer

Figur 5: Side view of the subwoofer illustrating its physical dimensions.

9. Garanti og support

JBL Stage 2 200P Powered Subwoofer comes with a limited warranty. For detailed information regarding warranty terms, conditions, and duration, please refer to the warranty card included in your product packaging or visit the official JBL webwebsted. For teknisk support, hjælp til fejlfinding eller serviceforespørgsler, kontakt venligst JBLs kundesupport via deres officielle kanaler.

Du kan besøge den officielle JBL-butik for at få flere oplysninger: JBL-butik på Amazon