1. Introduktion
This manual provides essential information for the safe and efficient operation of your InFocus IN112a SVGA DLP Projector. Please read it thoroughly before using the projector and retain it for future reference. The InFocus IN112a is designed to deliver clear and bright projections for various applications, featuring SVGA resolution, HDMI connectivity, and 3D support.
2. Sikkerhedsoplysninger
Overhold følgende sikkerhedsforanstaltninger for at forhindre skader på projektoren og sikre brugerens sikkerhed:
- Do not look directly into the projector lens når lamp er tændt. Det intense lys kan forårsage øjenskader.
- Sørg for tilstrækkelig ventilation. Bloker ikke ventilationsåbningerne.
- Only qualified service personnel should open the projector casing. Der er ingen dele indeni, som kan serviceres af brugeren.
- Brug kun den netledning, der følger med projektoren.
- Hold projektoren væk fra vand eller fugtige omgivelser.
- Projektoren lamp contains mercury. Dispose of lamps according to local regulations. Visit www.lamprecycle.org for mere information.
Billede: Bund view of the InFocus IN112a projector, displaying various warning labels, regulatory compliance marks (like CE, FCC), and information regarding the mercury content in the lamp and recycling instructions.
3. Produktet er slutview
3.1. Projektorens dimensioner
Billede: Forside view of the InFocus IN112a projector, illustrating its physical dimensions. The projector measures approximately 292 mm in width, 220 mm in depth, and 108 mm in height.
3.2. Betjeningselementer på øverste panel
Billede: Top view of the InFocus IN112a projector, highlighting the control panel. This panel includes buttons for power, menu access, source selection, and directional navigation for menu adjustments.
The top panel features buttons for power on/off, menu access, input source selection, and navigation arrows for adjusting settings within the on-screen display (OSD) menu. The focus and zoom rings are located near the lens.
3.3. Bagpaneltilslutninger
Billede: Bagside view of the InFocus IN112a projector, displaying its comprehensive array of connectivity ports. These include HDMI 1.4, two VGA inputs (Computer 1, Computer 2), a VGA monitor output, S-Video, Composite video, two 3.5mm stereo audio inputs, one 3.5mm stereo audio output, an RS232C control port, and a USB-B port.
The rear panel provides a variety of connection options:
- HDMI 1.4: Til digital video- og lydindgang.
- VGA (Computer 1, Computer 2): Two inputs for analog computer signals.
- VGA Monitor Out: For connecting an external monitor.
- Sammensat video: Til standardopløsningsvideoindgang.
- S-video: For enhanced standard definition video input.
- Audio In (3.5mm x 2): For stereo audio input.
- Lydudgang (3.5 mm): For stereo audio output to external speakers.
- RS232C: Til projektorstyring via en computer eller et styresystem.
- USB-B: Til service eller firmwareopdateringer.
4. Opsætning
4.1. Placering
Position the projector on a stable, flat surface or mount it securely to a ceiling. Ensure there is adequate space around the projector for ventilation. The distance from the screen will determine the image size. Refer to the specifications section for throw ratio details.
4.2. Tilslutning af strøm
Connect the supplied power cord to the projector's power inlet and then to a grounded electrical outlet. The power LED will illuminate, indicating standby mode.
4.3. Tilslutning af videokilder
Connect your video source (e.g., computer, Blu-ray player, cable box) to the appropriate input port on the projector's rear panel using a compatible cable. For best quality, use the HDMI input.
- HDMI: Connect an HDMI cable from your source to the projector's HDMI port.
- VGA: Connect a VGA cable from your computer to either the Computer 1 or Computer 2 port.
- Composite/S-Video: Connect the respective cable for older video sources.
4.4. Tilslutning af lyd
If using VGA, Composite, or S-Video inputs, connect an audio cable from your source's audio output to one of the projector's 3.5mm Audio In ports. HDMI carries both video and audio, so a separate audio connection is not typically needed for HDMI sources.
4.5. Adjusting Focus and Zoom
After powering on the projector and displaying an image, rotate the Fokusring around the lens until the image is sharp and clear. Use the Zoomring to adjust the image size to fit your screen.
5. Betjening
5.1. Tænd/sluk
- For at tænde: Press the Power button on the projector's top panel or the remote control. The power indicator will turn green.
- For at slukke: Press the Power button twice. The projector will enter a cooling cycle, and the power indicator will turn red (standby) once complete.
5.2. Valg af inputkilde
Press the "Source" button on the projector or remote control repeatedly to cycle through available input sources (HDMI, VGA1, VGA2, S-Video, Video). The projector will automatically detect an active signal if "Auto Source" is enabled in the menu.
5.3. Menu navigation
Press the "Menu" button to access the On-Screen Display (OSD) menu. Use the directional arrows to navigate through menu options and the "Enter" button to select. Press "Menu" again to exit.
5.4. 3D Content Playback
The IN112a supports 3D content from Blu-ray players, cable boxes, dish services (over HDMI), and PC-based 3D content at 120Hz. To view 3D content, you will need 144 Hz DLP Link 3D glasses (sold separately).
- Ensure your 3D source is connected via HDMI.
- Play 3D content from your source.
- Turn on your 144 Hz DLP Link 3D glasses. The projector should automatically detect the 3D signal.
6. Vedligeholdelse
6.1. Cleaning the Projector Lens
Gently wipe the lens with a soft, lint-free cloth specifically designed for optical surfaces. Do not use abrasive cleaners or excessive force, as this can scratch the lens.
6.2. Lamp Udskiftning
Projektoren lamp has a lifespan of up to 10,000 hours. When the lamp livet nærmer sig sin ende, kan der vises en advarselsmeddelelse, eller lamp indicator LED may illuminate. Refer to the full service manual for detailed lamp udskiftningsvejledning. Advarsel: Den lamp indeholder kviksølv. Bortskaf brugt lampi henhold til lokale miljøforskrifter.
6.3. Rengøring af luftfiltre
Regularly clean the air filters to ensure proper ventilation and prevent overheating. Dust and debris can accumulate, reducing cooling efficiency. Gently remove the filter cover and clean the filter with a soft brush or vacuum cleaner. Replace the filter cover securely.
7. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Intet billede vises |
|
|
| Billedet er sløret |
|
|
| Ingen lyd |
|
|
| Projektoren overopheder og slukker |
|
|
8. Specifikationer
| Feature | Detalje |
|---|---|
| Modelnummer | IN112X |
| Displayteknologi | DLP |
| Indfødt opløsning | SVGA (800x600) |
| Lysstyrke | Op til 3200 Lumens |
| Kontrastforhold | 15,000:1 |
| Lamp Liv | Op til 10,000 timer |
| Forbindelse | HDMI 1.4, VGA x 2, Composite video, S-Video, 3.5 mm stereo in x 2, 3.5mm stereo out, VGA monitor out, RS232C, USB-B |
| 3D-understøttelse | Yes (requires 144 Hz DLP Link 3D glasses) |
| Kasteforhold | 1.9 - 2.09 |
| Produktdimensioner | 14.25 x 12 x 7.75 tommer (ca. 36.2 x 30.5 x 19.7 cm) |
| Varens vægt | 5.4 pund (ca. 2.45 kg) |
| Anbefalet brug | Indendørs/Udendørs |
| Speciel funktion | Indbyggede højtalere |
9. Garanti og support
For warranty information and technical support, please refer to the documentation included with your purchase or visit the official InFocus webwebsted. Gem din købsbevis til garantikrav.
