Philips 24675-1 40W lysstofrør Lamp Instruktionsmanual

Vigtige sikkerhedsoplysninger

Read all instructions carefully before installing or using the Philips 24675-1 fluorescent lamp. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• ADVARSEL: Risiko for elektrisk stød. Afbryd strømmen før installation eller service.
• Sørg for at lamp is compatible with your fixture's ballast and voltage-krav (50 volt).
• Do not use with dimmers unless specifically rated for fluorescent lamps and compatible with the ballast.
• Håndtag lamps carefully. Avoid dropping or subjecting them to impact.
• Dispose of fluorescent lamps according to local regulations, as they contain mercury.
• Do not operate in wet locations or where directly exposed to water.

Opsætning og installation

This section provides instructions for safely installing your Philips 24675-1 fluorescent lamp.

Nødvendigt værktøj og materialer:

• Philips 24675-1 Fluorescent Lamp
• Compatible fluorescent fixture
• Stepladder (if necessary)
• Sikkerhedshandsker og øjenbeskyttelse

Installationstrin:

1. Trin 1: Afbryd strømmen. Locate the circuit breaker or fuse box that controls the power to the light fixture. Turn off the power completely. Bekræft, at strømmen er slukket, ved hjælp af en lydstyrkeindikator.tage-tester, hvis tilgængelig.
2. Trin 2: Fjern gammel Lamp (hvis relevant). Hvis du udskifter en eksisterende lamp, carefully twist the old fluorescent tube 90 degrees and gently pull it out of the lampholders. Dispose of the old lamp ordentligt.
3. Step 3: Insert New Lamp. Align the pins on both ends of the Philips 24675-1 fluorescent lamp med rillerne i l'etampholders of your fixture. Gently push the lamp ind i lampholderne, indtil stifterne sidder helt fast.
4. Step 4: Rotate Lamp. Once seated, rotate the lamp 90 degrees until it locks securely into place. Ensure both ends are firmly connected and the lamp er stabil.
5. Trin 5: Genopret strømmen. Når den lamp er sikkert installeret, skal du genoprette strømmen til armaturet fra afbryderen eller sikringsskabet.
6. Trin 6: Testdrift. Tænd lyskontakten for at bekræfteamp lyser.

Figur 1: Philips 24675-1 40W lysstofrør Lamp. This image shows the tubular shape and standard pins of the fluorescent lamp, ready for installation into a compatible fixture.

Betjeningsvejledning

Philips 24675-1 lysstofrøramp is designed for straightforward operation within a compatible fixture.

1. Tænd/sluk: Use the wall switch or fixture switch to turn the lamp til eller fra.
2. Opvarmningstid: Fluorescerende lamps may require a brief warm-up period (a few seconds) to reach full brightness, especially in colder environments.
3. Normal drift: Lamp will provide consistent illumination once fully warmed up.

Note: Frequent switching on and off can reduce the lifespan of fluorescent lamps. For optimal longevity, avoid rapid cycling.

Opretholdelse

Proper maintenance ensures optimal performance and extends the life of your Philips 24675-1 fluorescent lamp.

• Rensning: Ensure power is off before cleaning. Gently wipe the lamp with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials.
• Inspektion: Efterse lamp and fixture for any signs of damage, loose connections, or discoloration. If any issues are found, disconnect power and consult a qualified electrician.
• Udskiftning: Udskift lamp when it reaches the end of its average rated life (2000 hours) or if it begins to flicker excessively, dims significantly, or fails to illuminate.
• Bortskaffelse: Fluorescerende lamps contain small amounts of mercury. Do not dispose of them in regular household trash. Consult your local waste management authority for proper recycling or disposal procedures.

Fejlfinding

If you experience issues with your Philips 24675-1 fluorescent lamp, se følgende almindelige problemer og løsninger:

Produktspecifikationer

Detailed technical specifications for the Philips 24675-1 40W Fluorescent Lamp.

• Modelnummer: 24675-1
• Mærke: Philips
• Lystype: Fluorescerende
• Wattage: 40 watt
• Voltage: 50 volt
• Form: Rørformet (T)
• Lysstyrke: 140 lumen
• Farvetemperatur: 2700 Kelvin
• farvegengivelsesindeks (CRI): 80
• Gennemsnitlig levetid: 2000 timer
• Produktdimensioner: 1.75 x 1.75 x 24.5 tommer
• Varens vægt: 6.4 ounce
• Specifikke anvendelser: Lamp

Garanti og support

For warranty information or technical support regarding your Philips 24675-1 fluorescent lamp, please refer to the official Philips webhjemmeside eller kontakt deres kundeservice direkte.

Note: Warranty terms and conditions may vary by region and retailer. Keep your purchase receipt for warranty claims.