DWR-2000M 5G Router With ONT Modem
Product Information
Specifications:
- Product Name: DWR-2000M 5G Router with ONT Modem
- Internet Connectivity: 5G
- Interface: Web GUI
Product Usage Instructions:
Installation and Setup of Internet Connection:
- If you can browse the internet right away, no further setup is
needed. - If not, follow these steps to configure your internet
settings:
Configuration via Web GUI:
1. Open a web browser on a device connected to the DWR-2000M 5G
Router.
2. Enter the router’s IP address in the browser’s address bar
(e.g., 192.168.0.1).
3. Log in using the default credentials provided in the user
manual.
4. Navigate to the internet settings section in the Web GUI.
5. Configure the required settings such as IP address, DNS,
etc., based on your internet service provider’s specifications.
6. Save the changes and restart the router if necessary.
Frequently Asked Questions (FAQ):
Q: What should I do if I cannot access the internet after
setting up the DWR-2000M 5G Router?
A: Check the internet settings configured on the router and
ensure they match your ISP’s requirements. You may also try
restarting both the router and the modem.
Technical Support Setup Procedure
How do I install & set up internet on my DWR-2000M 5G Router with ONT Modem
For ISPs that use Dynamic (DHCP), PPPoE, or Static IP 1 Before you begin · Ask your ISP for your Internet connection type, Dynamic (DHCP), PPPoE (Username and Password), or Static IP · Some ISPs in Singapore (like Singtel, StarHub) may also require VLAN ID configuration in the router for internet to work. · Connect your computer directly to the ISP’s modem/ONT via Ethernet. If you can browse the internet, the connection is active 2 Physical Set up · Plug one end of an Ethernet cable into the WAN/LAN port of your router, and the other end into the LAN port of your ONT/modem.
· Power up the ONT first, wait until its PON/LOS lights are normal, then power on your DWR-2000M router.
· Checked LED light on the router (Power and Wi-Fi LEDs should be solid green) · Connect your phone, tablet, or laptop, find the router’s default Wi-Fi name (SSID)
and password printed on the label at the back of the router. · Test your connection:
o If you can browse the internet right away, no further setup is needed. o If not, follow the steps below to configure your internet settings. 3 Configuration via Web GUI
Technical Support Setup Procedure
· Connect your PC / Laptop to DWR-BE7200G either Wi-Fi or Ethernet. The default Wi-Fi network name (SSID) is DLink2G-XXXX and DLink5G-XXXX, with the password printed on the product label
· Once connected, open a web browser and type in https://192.168.0.1 on the address bar and hit enter.
· You will be prompted to enter the Username and Password to access the router’s settings. Note: The default Username and Password are printed on the router’s label at the bottom
· Click Login to proceed.
Note: If you have changed the password and cannot remember it, you will need to perform a hard reset on the router 4 Choosing Your Internet Connection Type · Go to Internet Settings, then select your Access type from the drop-down menu
Technical Support Setup Procedure
o Dynamic (DHCP) Used by most cable or fiber setups. Simply select Dynamic, then click Save.
o PPPoE Common for DSL or fiber connections. Select PPPoE. Enter your username and password from your ISP. Input the VLAN ID only if your ISP requires it; otherwise, keep it set to Disabled Click Save.
o Static IP If your ISP gave you a fixed IP address. Enter your IP address, Subnet Mask, Gateway, and DNS details exactly as provided. Click Save.
o LAN If the router will use a SIM card (mobile data) as the internet source, select this option.
5 Failover Feature DWR-2000M supports failover, meaning if your primary connection lost connection, it will automatically switch to your backup connection, if not required, keep this option disable. · Primary: Mobile Network Select Ethernet for backup. · Primary: Fixed ISP Connection Select Mobile for backup.
Once saved, the router should connect to the internet within a few seconds. If it doesn’t: · Reboot your ONT Modem by plugging it in for 10 seconds, then plugging it back in. · Double-check your connection type and credentials with your ISP.
—END—
Documents / Resources
 |
D-Link DWR-2000M 5G Router With ONT Modem [pdf] User Guide DWR-2000M, DWR-2000M 5G Router With ONT Modem, 5G Router With ONT Modem, Router With ONT Modem, ONT Modem |