CVTE Ax 2T2R USB WiFi Module
Introduction
- SKI.WB921AU.1 module is based on MediaTek MT7921AU solution.
- MT7921A is a highly integrated single chip which features a low power 2×2 lla/b/g/n/ac/ax dual-band Wi-Fi subsystem and a Bluetooth vS.2 subsystem, offering feature-rich wireless connectivity at high standards ,and delivering reliable ,cost-effective throughput from an extended distance.
- MT7921AUN data rate up to 800Mbps with USB3.0.Optimized RF architecture and baseband algorithms provide superb performance and low power consumption. Intelligent MAC design deploys a high efficient offload engine ,and hardware data processing accelerators which fully offloads Wi-Fi task of the host processor, MT7921A is designed to support standard based features in the areas of security, quality of service and international regulations, giving end users the greatest performance any time and in any circumstance. This documentation describes the engineering requirements specification.
Features
Reserving System | IEEE Std. 802.lla |
IEEE Std. 802.llb | |
IEEE Std. 802.llg | |
IEEE Std. 802.lln IEEE Std. 802.llac
IEEE Std. 802.llax(SGHz) |
|
IEEE Std. 802.11ax(6GHz) | |
BT 2.l+EDR | |
BT4.2 |
BT 5.2 with BLE (BT low energy) | |
Chip Solution | MT7921AU |
Band & occupied band widthilt |
BT: 2400-2483.SMHz@:;c;3MHz WiFi:2400-2483.SMHz@:;c;4QMHz
5150-5350MHz@:;c;8QMHz 5725-5850MHz@:;c;8QMHz |
Modulation system |
WiFi: DBPSK/DQPS K/CCK/BPS K/QPSK/ 16QAM/64QAM/256QAM/1024Q AM
BT:GFSK, n/4-DQPSK, 8-DPSK |
Dimensions R-r | 30mmx23mmx2.6mm |
Model | Installation Mode | Protocol I | Frequency | Antenna | Remark |
SKI.WB921AU.1 | SMD | IEEE 802.1la/b/g/n/ac/ax
BT 2.l+EDR/4.2/5.2 |
2.4GHz/5GHz
/6GHz |
WiFi & BT: Ipex | 30mmx23mm
X2.6mm |
Block Diagram
Figure 1 SKI.WB921AU.1 Block Diagram
Package Outline and Mounting
Pin Definition
![]() |
||
PIN | SYMBOL | DESCRIPTION |
1 | GND | GND |
2 | NC | Not connect |
3 | NC | Not connect |
4 | GND | GND |
5 | RESET | PMU RESET |
6 | GND | GND |
7 | GND | GND |
8 | 3.3V | 3.3V |
9 | 3.3V | 3.3V |
10 | GND | GND |
11 | NC | Not connect |
12 | NC | Not connect |
13 | GPI013 | DEBUG,WL FW LOG |
14 | GPI04 | DEBUG,BT FW LOG |
15 | GND | GND |
16 | WIFI_WAKE | WIFI |
17 | GPIO12 | ICE DEBUG |
18 | Gili | ICE DEBUG |
19 | NC | Not connect |
20 | GND | GND |
21 | U3-TXN | USB3.0 TXN, |
22 | U3-TXP | USB3.0 TXP,; |
23 | GND | GND |
24 | NC | Not connect |
25 | NC | Not connect |
26 | GND | GND |
27 | U3-RXN | USB3.0 |
28 | U3-RXP | USB3.0 |
29 | GND | GND |
30 | U2-DP | USB2.0 DP, |
31 | U2-DM | USB2.0 DM, |
32 | GND | GND |
33 | NC | Not connect |
34 | BT_WAKE | BT |
35 | NC/BT_Stereo | Not connect/BT_Stereo |
36 | NC | Not connect |
37 | GND | GND |
38 | NC | Not connect |
39 | NC | Not connect |
40 | NC | Not connect |
41 | NC | Not connect |
42 | GND | GND |
43 | GND | GND |
44 | GND | GND |
45 | WiFi1 | Not connect (ipex) |
46 | GND | GND |
47 | GND | GND |
48 | WiFi0 | Not connect(ipex) |
49 | GND | GND |
50 | GND | GND |
51 | BT! | Not connect( ipex) |
52 | GND | GND |
53 | GND | GND |
54 | BT0 | Not connect(ipex) |
55 | GND | GND |
Product Pictures
(top view)
CVTE
CVTE ‘l4 | ||
SKLWB921AU,1 | 1: 002.029.0000435 | IPEX 1: 4 . 2WiFi+2 BT USB3,0-5G |
2: 002,029.0000436 | IPEX : 3 . 2WiFi+1BT. BT0, ± BT) , USB3,0-5G | |
‘ 3: 002.029.0000874 | : 4 t . 2WiFi+2 BT USB3.0-5G | |
4, 002.029.0000969 | IPEX 1: 4 . 2WiFi+2 BT , USB3,0-2.5G | |
5, 002.029.0000995 | IPEX 1\: 4 . 2WiFi+2 BT ‘, USB3,0-5G(xt.\’ BT_Stereo) |
(bottom view)
(information view)
Key Materials
1 | MT7921AU | 109-DRQFN | ||
2 | PCB | SKI.WB921AU.1 | FR-4,4LAY | |
3 | CF4040M00006T2115218 | 40MHz |
The device is restricted to indoor use when operating in 5150-5350MHz frequency range.
General Requirements
No. | Feature | Description |
7-1 | Operation Voltage | 3.3V+/-0.3 |
7-2 | Current Consumption | 900mA 2A) |
7-3 | Ripple | ,S120mV |
7-4 | Operation Temperature | -10°C to + 70°C |
7-5 | Antenna Type | External antenna |
7-6 | USB | High Speed USB 3.0 Interface
High Speed USB 2.0 Interface) |
7-7 | Storage Temperature Zf.1it1llli.& | -40°C to +125°C |
Interface Timing Specification
Ps:
- After 3.3V power supply is stabilized, PMU_EN can be pulled up again (Delta 1>0);
- It is recommended that the main chip be pulled down again PMU _ EN after the WIFI power is stabilized.
Electrical Characteristics
The Test for electrical specification was performed under the following condition unless otherwise specified:
- Ambient condition Temperature :25’C ± S’C;
- Power supply voltages, 3.3V+/-0.3 input power at the Module;
IEEE 802.llb Section(2.4GHz)
Items | Contents | ||||
Specification | IEEE802.11b | ||||
Mode | CCK | ||||
Channel | CH1 to CH13 | ||||
TX Characteristics | Min. | Typ. | Max. | Unit | Remark |
1. Power Levels(Calibrated) | |||||
1) For antenna port ( CCK 11 M) | 15 | 17 | 19 | dBm | |
2. Spectrum Mask @ target power | |||||
1) fc +/-11MHz to +/-22MHz | -30 | dBr | |||
2) fc > +/-22MHz | -50 | dBr | |||
3 Constellation Error(EVM)@ target power | |||||
1) !Mbps | -10 | dB | |||
2) 2Mbps | -10 | dB | |||
3) 5.5Mbps | -10 | dB | |||
4) 11Mbps | -10 | dB | |||
4. Frequency Error | -20 | 20 | ppm | ||
RX Characteristics | Min. | Typ. | Max. | Unit | |
5 Minimum Input Level Sensitivity
(each chain) |
|||||
1) !Mbps (FER ;£8%) | -83 | dBm | |||
2) 2Mbps (FER ;£8%) | -80 | dBm | |||
3) 5.5Mbps (FER ;£8%) | -79 | dBm | |||
4) 11Mbps (FER ;£8%) | -76 | dBm | |||
6 Maximum Input Level (FER ;£8%) | -10 | dBm |
IEEE 802.llg Section(2.4GHz)
Items | Contents | ||||
Specification | IEEE802.11g | ||||
Mode | OFDM | ||||
Channel | CH1 to CH13 | ||||
TX Characteristics | Min. | Typ. | Max. | Unit | Remark |
1. Power Levels | |||||
1) For antenna port ( 54M) | 14 | 16 | 18 | dBm | |
2. Spectrum Mask @ target power | |||||
1) at fc +/-11MHz | -20 | dBr | |||
2) at fc +/-20MHz | -28 | dBr | |||
3) at fc > +/-30MHz | -40 | dBr | |||
3 Constellation Error(EVM)@ target power | |||||
1) 6Mbps | -5 | dB | |||
2) 9Mbps | -8 | dB |
3) 12Mbps | -10 | dB | |||
4) 18Mbps | -13 | dB | |||
5) 24Mbps | -16 | dB | |||
6) 36Mbps | -19 | dB | |||
7) 48Mbps | -22 | dB | |||
8) 54Mbps | -25 | dB | |||
4 Frequency Error | -20 | 20 | ppm | ||
RX Characteristics | Min. | Typ. | Max. | Unit | |
5 Minimum Input Level Sensitivity
(each chain) |
|||||
1) 6Mbps (PER ;£10%) | -85 | dBm | |||
2) 9Mbps (PER ;£10%) | -84 | dBm | |||
3) 12Mbps (PER ;£10%) | -82 | dBm | |||
4) 18Mbps (PER ;£10%) | -80 | dBm | |||
5) 24Mbps (PER ;£10%) | -77 | dBm | |||
6) 36Mbps (PER ;£10%) | -73 | dBm | |||
7) 48Mbps (PER ;£10%) | -69 | dBm | |||
8) 54Mbps (PER ;£10%) | -65 | dBm | |||
6 Maximum Input Level (PER ;£10%) | -20 | dBm |
IEEE 802.lln HT20 Section(2.4GHz)
Items | Contents | ||||
Specification | IEEE802.lln HT20@ 2.4GHz | ||||
Mode | OFDM | ||||
Channel | CHl to CH13 | ||||
TX Characteristics | Min. | Typ. | Max. | Unit | |
1. Power Levels | |||||
1) For antenna port ( MCS7) | 13 | 15 | 17 | dBm | |
2. Spectrum Mask @ target power | |||||
1) at fc +/-llMHz | -20 | dBr | |||
2) at fc +/-20MHz | -28 | dBr | |||
3) at fc > +/-30MHz | -45 | dBr | |||
3. Constellation Error(EVM)@ target power | |||||
1) MCS0 | -5 | dB | |||
2) MCSl | -10 | dB | |||
3) MCS2 | -13 | dB | |||
4) MCS3 | -16 | dB | |||
5) MCS4 | -19 | dB | |||
6) MCS5 | -22 | dB | |||
7) MCS6 | -25 | dB | |||
8) MCS7 | -28 | dB |
4. Frequency Error | -20 | 20 | ppm | ||
RX Characteristics | Min. | Typ. | Max. | Unit | |
5.Minimum Input Level Sensitivity
(each chain) |
|||||
1) MCS0 (PER10%) | -82 | dBm | |||
2)MCSl (PER10%) | -79 | dBm | |||
3)MCS2 (PER10%) | -77 | dBm | |||
4)MCS3 (PER10%) | -74 | dBm | |||
5)MCS4 (PER10%) | -70 | dBm | |||
6)MCS5 (PER10%) | -66 | dBm | |||
7)MCS6 (PER10%) | -65 | dBm | |||
8)MCS7 (PER10%) | -64 | dBm | |||
7.Maximum Input Level (PER10%) | -20 | dBm |
IEEE 802.lln HT40 Section(2.4GHZ)
Items | Contents | ||||
Specification | IEEE802.lln HT40@ 2.4GHz | ||||
Mode | OFDM | ||||
Channel | CH3 to CHll | ||||
TX Characteristics | Min. | Typ. | Max. | Unit | |
1. Power Levels (Calibrated) | |||||
1) For antenna port ( MCS7) | 13 | 15 | 17 | dBm | |
2. Spectrum Mask @target power | |||||
1) at fc +/-22MHz | -20 | dBr | |||
2) at fc +/-40MHz | -28 | dBr | |||
3) at fc > +/-60MHz | -45 | dBr | |||
3. Constellation Error(EVM)@ target power | |||||
1) MCS0 | -5 | dB | |||
2) MCSl | -10 | dB | |||
3) MCS2 | -13 | dB | |||
4) MCS3 | -16 | dB | |||
5) MCS4 | -19 | dB | |||
6) MCS5 | -22 | dB | |||
7) MCS6 | -25 | dB | |||
8) MCS7 | -28 | dB | |||
4. Frequency Error | -20 | 20 | ppm | ||
RX Characteristics | Min. | Typ. | Max. | Unit | |
5. Minimum Input Level Sensitivity
(each chain) |
|||||
1) MCS0 (PER10%) | -79 | dBm | |||
2)MCSl (PER10%) | -76 | dBm | |||
3)MCS2 (PER10%) | -74 | dBm |
4) MCS3 (PER ;£10%) | -71 | dBm | |||
5) MCS4 (PER ;£10%) | -67 | dBm | |||
6) MCS5 (PER ;£10%) | -63 | dBm | |||
7) MCS6 (PER ;£10%) | -62 | dBm | |||
8) MCS7 (PER ;£10%) | -61 | dBm | |||
6. Maximum Input Level (PER ;£10%) | -20 | dBm |
IEEE 802.llax Section(2.4GHz)
Items | Contents | ||||||
Specification | IEEE802. l lax | ||||||
Mode |
BPSK, QPSK, 16QAM, 64QAM,256QAM,
1024QAM and OFDMA |
||||||
Channel |
HE20: CHl to CH13
HE40: CH3 to CHll |
||||||
TX Characteristics | Min. | Typ. | Max. | Unit | |||
1. Power Levels (Calibrated) | |||||||
1) For antenna port ( MCSll) | 11 | 13 | 15 | dBm | |||
2. Spectrum Mask @VHT20/VHT40/VHT80
target power |
|||||||
1) at fc +/-11MHz/21MHz/41MHz | -20 | dBr | |||||
2) at fc +/-20MHz/40MHz/80MHz | -28 | dBr | |||||
3) at fc +/-30MHz/60MHz/120MHz | -40 | dBr | |||||
3. Constellation Error(EVM)@ target power | |||||||
1) MCS0 | -5 | dB | |||||
2) MCSl | -10 | dB | |||||
3) MCS2 | -13 | dB | |||||
4) MCS3 | -16 | dB | |||||
5) MCS4 | -19 | dB | |||||
6) MCS5 | -22 | dB | |||||
7) MCS6 | -25 | dB | |||||
8) MCS7 | -27 | dB | |||||
9) MCS8 | -30 | dB | |||||
10) MCS9 | -32 | dB | |||||
11) MCSl0 | -34 | dB | |||||
12) MCSll | -35 | dB | |||||
4. Frequency Error | -20 | 20 | ppm | ||||
RX Characteristics | Min. | Typ. | Max. | Unit | |||
5.Minimum Input Level Sensitivity
(each chain) |
HE
20 |
HE
40 |
|||||
1) MCS0 (PER ;£10%) | -82 | -79 | dBm | ||||
2) MCSl (PER ;£10%) | -79 | -76 | dBm |
3) MCS2 (PER ;£10%) | -77 | -74 | dBm | ||||
4) MCS3 (PER ;£10%) | -74 | -71 | dBm | ||||
5) MCS4 (PER ;£10%) | -70 | -67 | dBm | ||||
6) MCS5 (PER ;£10%) | -66 | -63 | dBm | ||||
7) MCS6 (PER ;£10%) | -65 | -62 | dBm | ||||
8) MCS7 (PER ;£10%) | -64 | -61 | dBm | ||||
9) MCS8(PER ;£10%) | -59 | -56 | dBm | ||||
10) MCS9(PER ;£10%) | -57 | -54 | dBm | ||||
11) MCSl0(PER ;£10%) | -54 | -51 | dBm | ||||
12) MCSll(PER ;£10%) | -52 | -49 | dBm | ||||
6. Maximum Input Level (PER ;£10%) | -30 | dBm |
IEEE 802.11a Section(SGHz)
Items | Contents | ||||
Specification | IEEE802. l la | ||||
Mode | OFDM | ||||
Channel | CH36 to CH165 | ||||
TX Characteristics | Min. | Typ. | Max. | Unit | |
1. Power Levels (Calibrated) | |||||
1) For antenna port ( 54M) | 14 | 16 | 18 | dBm | |
2. Spectrum Mask @target power | |||||
1) at fc +/-llMHz | -20 | dBr | |||
2) at fc +/-20MHz | -28 | dBr | |||
3) at fc > +/-30MHz | -40 | dBr | |||
3. Constellation Error(EVM)@ target power | |||||
1) 6Mbps | -5 | dB | |||
2) 9Mbps | -8 | dB | |||
3) 12Mbps | -10 | dB | |||
4) 18Mbps | -13 | dB | |||
5) 24Mbps | -16 | dB | |||
6) 36Mbps | -19 | dB | |||
7) 48Mbps | -22 | dB | |||
8) 54Mbps | -25 | dB | |||
4 Frequency Error | -20 | 20 | ppm | ||
RX Characteristics | Min. | Typ. | Max. | Unit | |
5 Minimum Input Level Sensitivity
(each chain) |
|||||
1) 6Mbps (PER ::;; 10%) | -82 | dBm | |||
2) 9Mbps (PER ::;; 10%) | -81 | dBm | |||
3) 12Mbps (PER ::;; 10%) | -79 | dBm | |||
4) 18Mbps (PER ::;; 10%) | -77 | dBm |
Documents / Resources
![]() |
CVTE Ax 2T2R USB WiFi Module [pdf] Owner's Manual Ax 2T2R, Ax 2T2R USB WiFi Module, USB WiFi Module, WiFi Module, Module |