TCP ISREMOTE Remote Control
Specifikace produktu
- Značka: TCP
- Produkt: Dálkové ovládání
- Model: ISREMOTE
- Works with any IS Motion Sensor
- Customization of luminaires
The TCP IS Remote works with any IS Motion Sensor to allow easy customization of any of your luminaires.
Remote Usage Instructions
Jas LED
Set the brightness level when occupancy is sensed and luminaire is switched on.
Citlivost
Adjust the occupancy sensing sensitivity of the sensor.
Hold Time
Set the duration the sensor remains at full brightness before turning off or entering standby mode.
Senzor denního světla
Preset threshold levels for the daylight sensing functions.
*In applicable sensors only
Pohotovostní ztlumení
Adjust the lux value to act as the daylight threshold. This feature enables daylight sensor functionality in all applications. (Only applicable in certain sensors)
Pohotovostní doba
To set the bi-level dimming after the initial hold time. Setting standby dim level at 0% means the device will turn off after the initial hold time (Standard mode). Setting standby dim level to the other provided options will place the device in bi-level mode.
Set the current lux value as the daylight threshold. This feature enables the daylight sensor to function in all applications.
*In applicable sensors only
The daylight sensor is turned off and the sensor functions in standard or bi-level dimming mode.
Tlačítko ON/OFF
Press the ON/OFF button, the light goes to permanent on or permanent off mode, and the sensor is disabled (Must press the AUTO button to quit this mode for setting).
Display the current/latest setting parameters in LED indicators (the LED indicators will turn on for showing the setting parameters).
Tlačítko RESET
Press RESET button, all settings go back the settings of the dip switch in sensor.
Tlačítko SELECT
Select active parameter for editing after pressing DISP. The selected function will flash.
Tlačítko OK
Select OK to save the selected settings to the remote.
Settings will be saved to the remote but will still need sent to the device
SEND Button
Press the SEND button to upload the current settings to the fixture (Press DISP to see current settings.) The fixture will flash on/off to confirm the settings have been received.
4 scénické režimy s přednastavenými parametry, které lze v režimech měnit a ukládat.
Tlačítko AUTO
Press AUTO button, the sensor starts to function and all settings remain the same as the latest status before the light is switched on/off.
TEST 2s Button
The button TEST 2s is for testing purpose sensitivity only after you choose sensitivity thresholds, then you press the TEST 2s button.
The sensor goes to test mode (hold time is only 2s) automatically, meanwhile the standby period and daylight sensor are disabled. Press AUTO button to quit from this mode.
LEFT/RIGHT Buttons
Navigate to LEFT and RIGHT to choose between options of the selected parameters in LED indicators
Tlačítka NAHORU/DOLŮ
Open and close smart daylight sensor. Press UP or DOWN, enter in the setting condition, the parameter LEDs of remote control will flash to be selected, press this button to open or close smart daylight sensor.
*In applicable sensors only
TECHNOLOGIE ODLIZENÁ V KRÁSNÉM SVĚTLE
Společnost TCP již více než 30 let navrhuje, vyvíjí a dodává energeticky účinné osvětlení na trh. Díky naší špičkové technologii a výrobním znalostem jsme dodali miliardy vysoce kvalitních světelných produktů. S TCP se můžete spolehnout na osvětlovací produkt, který je navržen tak, aby vyhovoval potřebám trhu – který promění vaše okolí a zahalí vás do tepla – osvětlení, které vytváří krásu s každým přepnutím vypínače.
Pro více informací o kvalitě a péči, kterou může TCP poskytnout, nám zavolejte na číslo 800.324.1496 nebo navštivte tcpi.com
325 Campnás Dr. | Aurora, Ohio 44202 | P: 800.324.1496 877.487.0516 XNUMX | F: XNUMX XNUMX XNUMX
Často kladené otázky
Q: How do I know if my sensor is compatible with the TCP IS Remote?
A: The TCP IS Remote works with any IS Motion Sensor, ensuring compatibility for customization of luminaires.
Q: Can I adjust the daylight sensing functionality of my luminaire?
A: Yes, you can set threshold levels and adjust the sensitivity of the daylight sensor in applicable sensors.
Dokumenty / zdroje
 |
TCP ISREMOTE Remote Control [pdfNávod k obsluze ISREMOTE, ISREMOTE Remote Control, ISREMOTE, Remote Control, Control |