ADATA Fusion 1600W Titanium Power Supply Unit User Manual

1. Úvod

This manual provides essential information for the proper installation, operation, and maintenance of your ADATA Fusion 1600W Titanium Power Supply Unit (PSU). Designed for high-performance computing systems, this 80 Plus Titanium certified PSU features ATX 3.0 and PCIe 5.0 compatibility, ensuring stable and efficient power delivery. Please read this manual thoroughly before proceeding with installation or use.

2. Bezpečnostní informace

• Elektrické nebezpečí: Power supplies contain high voltage components. Do not open the PSU casing. Servicing should only be performed by qualified personnel.
• Odpojení napájení: Always disconnect the AC power cord from the wall outlet before installing, removing, or cleaning the PSU or any other computer components.
• Správné uzemnění: Ensure your computer system and the wall outlet are properly grounded to prevent electrical shock.
• Větrání: Do not block the ventilation openings of the PSU. Ensure adequate airflow within your computer case to prevent overheating.
• vlhkost: Keep the PSU away from water, humidity, and other liquids.
• Teplota: Operate the PSU within the specified temperature range. Avoid extreme heat or cold.
• Správa kabelů: Route cables carefully to avoid pinching or damage, which can lead to short circuits or fire hazards.

3. Obsah balení

Ověřte, zda jsou v balení přítomny všechny položky:

• ADATA Fusion 1600W Titanium Power Supply Unit
• Modular Cable Set (including Motherboard, CPU, PCIe/GPU, SATA, and Molex cables)
• AC napájecí kabel
• Montážní šrouby
• Uživatelská příručka (tento dokument)

4. Nastavení

4.1. Fyzická instalace

1. Ensure your computer is powered off and the AC power cord is disconnected from the wall outlet.
2. Otevřete skříň počítače.
3. Locate the PSU mounting area, typically at the bottom or top rear of the case.
4. Carefully slide the ADATA Fusion PSU into the designated slot.
5. Připevněte zdroj k skříni pomocí dodaných montážních šroubů.

4.2. Připojení kabelů

The ADATA Fusion 1600W PSU is fully modular, allowing you to connect only the cables required for your system. Refer to the image below for port identification.

This image displays the ADATA Fusion 1600W Titanium Power Supply Unit from an angled top-down perspective. The modular cable connection panel is visible on the left side, labeled for SATA & Molex, Prime Port - Motherboard, CPU & VGA, and 12VHPWR. The top features a fan grill with a geometric pattern, revealing the cooling fan beneath. The side of the unit shows the 'FUSION' branding.

1. Napájení základní desky: Connect the 24-pin ATX cable from the PSU to the corresponding port on your motherboard.
2. Výkon CPU: Connect the 4+4-pin or 8-pin EPS/CPU cable(s) from the PSU to the CPU power connector(s) on your motherboard.
3. PCIe/GPU Power: Connect the appropriate 6+2-pin or 12VHPWR PCIe 5.0 cables from the PSU to your graphics card(s). Ensure all required power connectors on your GPU are utilized.
4. SATA/Molex Power: Connect SATA power cables to your storage drives (HDDs, SSDs) and optical drives. Use Molex cables for other peripherals as needed.
5. Periferní připojení: Connect any other necessary cables for case fans, RGB controllers, or other components.
6. Napájení střídavým proudem: Once all internal connections are made, connect the AC power cord to the PSU and then to a grounded wall outlet.

5. Provoz

After completing the installation and cable connections:

1. Ensure the power switch on the back of the PSU is in the 'ON' position.
2. Power on your computer system.
3. The ADATA Fusion PSU is designed for efficient and stable operation. Its 80 Plus Titanium certification indicates high power efficiency, reducing heat generation and energy consumption.
4. This PSU supports Prime Ecosystem Management Software. Refer to the ADATA website for software download and instructions on monitoring and controlling PSU performance, fan speeds, and other features.

6. Údržba

• Čištění: Periodically clean the exterior of the PSU and the fan grill to prevent dust buildup. Use compressed air to gently remove dust from the fan and internal components (ensure the PSU is powered off and unplugged).
• Kontrola kabelů: Pravidelně kontrolujte všechny kabelové spoje, zda jsou bezpečné a nepoškozené.
• Podmínky prostředí: Maintain a clean, dry, and well-ventilated environment for your computer system to optimize PSU lifespan and performance.

7. Řešení problémů

If you encounter issues with your ADATA Fusion PSU, consider the following common troubleshooting steps:

• Bez napájení:
  • Ujistěte se, že je napájecí kabel bezpečně připojen k napájecímu zdroji i k elektrické zásuvce.
  • Verify the PSU power switch is in the 'ON' position.
  • Zkontrolujte zásuvku pomocí jiného zařízení, abyste se ujistili, že je pod napětím.
  • Ensure all modular cables are firmly seated in both the PSU and the respective components.
• Nestabilita/pády systému:
  • Confirm that your PSU wattage is sufficient for all installed components.
  • Zkontrolujte, zda nejsou uvolněné kabelové spoje.
  • Sledujte teplotu systému, abyste se ujistili, že se jeho komponenty nepřehřívají.
• Hlučnost ventilátoru:
  • Ensure the PSU fan is not obstructed by cables or dust.
  • If using Prime Ecosystem Management Software, check fan speed settings.

If problems persist after attempting these steps, contact ADATA customer support for further assistance.

8. Specifikace

9. Záruka a podpora

ADATA provides a limited warranty for the Fusion 1600W Titanium Power Supply Unit. For detailed warranty terms, conditions, and registration information, please visit the official ADATA webwebu nebo se podívejte na záruční list dodaný s vaším produktem.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact ADATA customer service through their official webwebu nebo kontaktních informací uvedených na obalu produktu.

ADATA Official Webmísto: www.adata.com