HOBBYWING JUSTOCK G2.1 Brushless Motor Instruction Manual

Zavedení

This manual provides essential information for the proper installation, operation, and maintenance of your HOBBYWING JUSTOCK G2.1 brushless motor. Designed for 1/10 and 1/12 scale RC vehicles, this motor is compliant with ROAR and IFMAR rules, featuring zero timing for spec racing.

Key features include a heat-resistant magnet attached aluminum case, double insulated windings, high precision bearings, and a robust rotor structure for durability and performance. The built-in Hall sensor and non-adjustable end bell ensure smooth and linear power delivery.

Bezpečnostní informace

Varování: This item is not a toy. It contains small parts and electrical components. Adult supervision is recommended during assembly and operation, especially for users under 16 years of age.

• Před jakoukoli údržbou nebo instalací vždy odpojte baterii.
• Zajistěte řádné větrání během provozu, aby nedošlo k přehřátí.
• Zabraňte kontaktu s pohyblivými částmi během provozu.
• Do not expose the motor to water or excessive moisture unless specifically designed for such conditions.
• Use only compatible electronic speed controllers (ESCs) and batteries.

Nastavení a instalace

Proper installation is crucial for optimal performance and longevity of your motor.

1. Montáž motoru

Securely mount the motor to your vehicle's motor mount using appropriate screws. Ensure the motor is aligned correctly with the pinion gear to prevent excessive wear and friction.

Obrázek 1: Strana view of the HOBBYWING JUSTOCK G2.1 Brushless Motor, showing the sensor port and mounting holes.

2. Připojení vodičů

Connect the motor to your Electronic Speed Controller (ESC) according to the ESC's instructions. Typically, the three motor wires (A, B, C) connect to the corresponding output terminals on the ESC. Ensure correct polarity and secure connections.

• Senzorový kabel: Connect the sensor cable from the motor to the sensor port on your ESC. This is essential for sensored operation and smooth low-speed performance.
• Připojení baterie: Connect your battery to the ESC, ensuring correct polarity. The motor supports 2S-3S LiPo batteries.

Obrázek 2: Nahoře view of the HOBBYWING JUSTOCK G2.1 Brushless Motor, indicating the A, B, C terminals for ESC connection and the fixed timing end bell.

3. Gear Ratio Selection

Select an appropriate gear ratio for your vehicle and track conditions. Refer to your vehicle's manual or consult experienced users for recommendations. Incorrect gearing can lead to overheating and reduced performance.

Návod k obsluze

Once installed and connected, the HOBBYWING JUSTOCK G2.1 motor is ready for operation. This motor is designed for zero timing spec racing.

• Počáteční zapnutí: Turn on your transmitter first, then connect the battery to the ESC.
• Kalibrace: If necessary, calibrate your ESC with the motor and transmitter according to your ESC's manual.
• Běh: Operate your RC vehicle as usual. Monitor motor temperature during initial runs to ensure proper gearing and setup.
• Vypnutí: Nejprve odpojte baterii od regulátoru (ESC) a poté vypněte vysílač.

This motor is perfectly matched with the HOBBYWING XR10-JUSTOCK ESC for all zero timing spec racing and is also compatible with other HOBBYWING electronic speed controllers and other brands.

Údržba

Regular maintenance will prolong the service life and improve the operating efficiency of your JUSTOCK motor.

• Čištění: The motor features a detachable structure design for daily cleaning. Carefully disassemble the motor (if comfortable) to clean out dirt, dust, and debris from the internal components. Use compressed air or a soft brush.
• Kontrola ložisek: Periodically check the motor bearings for smooth operation. Replace worn or noisy bearings to maintain efficiency.
• O-Ring Seal: The silicone O-ring seal between the end bell and stator helps conduct inner heat and prevent dust. Ensure it is clean and properly seated.
• Kontrola připojení: Pravidelně kontrolujte všechna kabelová spojení, zda nevykazují známky opotřebení, koroze nebo uvolnění.

Odstraňování problémů

If you encounter issues with your motor, consider the following common troubleshooting steps:

• Motor neběží:
  • Zkontrolujte všechna zapojení mezi motorem, ESC a baterií.
  • Ujistěte se, že je baterie nabitá a správně připojená.
  • Verify ESC calibration with the transmitter.
  • Inspect the sensor cable for damage or improper connection.
• Přehřívání:
  • Check your gear ratio; it might be too aggressive.
  • Ensure there is adequate airflow to the motor.
  • Verify that the motor is not binding or experiencing excessive friction.
• Irregular Performance / Cogging:
  • Re-check sensor cable connection and ensure it's not damaged.
  • Ensure all motor phase wires are securely connected.
  • Zkontrolujte, zda uvnitř motoru nejsou nečistoty.

If problems persist, contact HOBBYWING customer support or consult with an experienced RC hobbyist.

Specifikace

Záruka a podpora

Legal Disclaimer and Warranty Information

Because HOBBYWING has no control over the use, installation, or maintenance of this product, no liability may be assumed for any damage or losses resulting from the use of the product. HOBBYWING does not assume responsibility for any losses caused by unauthorized modifications to its products. HOBBYWING reserves the right to modify product design, appearance, features, and usage requirements without prior notification.

HOBBYWING is only responsible for the product cost. Products purchased from Hong Kong / Chinese retailers may not conform to CE / North America regulations, and such products are deemed non-warranty. Discount / auction stores such as eBay are considered "non-authorized sales channels" in North America, and products purchased from these channels are also deemed non-warranty.

Zákaznická podpora

For technical assistance or further inquiries, please visit the official HOBBYWING website or contact your local authorized dealer. Ensure you have your product model number (30408013) and purchase details available when seeking support.