Návod k použití

1. Úvod

This manual provides detailed instructions for the installation, setup, and operation of your Scimagic-RC Tuya WiFi 433MHZ Receiver, 1527 Remote Control, and Wireless Numeric Keypad. This system is designed to provide secure and convenient access control for automatic garage doors, swing gates, and sliding gate openers, integrating with smart home platforms like Tuya, Smart Life, Google Assistant, and Amazon Alexa.

2. Bezpečnostní informace

• Před zahájením jakýchkoli zapojení nebo instalačních postupů se ujistěte, že je odpojeno veškeré napájení.
• Installation should be performed by qualified personnel if you are unsure about electrical connections.
• Udržujte zařízení mimo dosah vody a extrémních teplot.
• Do not attempt to repair the device yourself; contact support for assistance.
• This device is intended for use with automatic door/gate systems only.

3. Obsah balení

V závislosti na vašem nákupu může váš balíček obsahovat:

• Bezdrátová numerická klávesnice
• 433MHZ Receiver
• 433MHZ Remote Control (may be sold separately or in combinations)
• Montážní materiál (šrouby, hmoždinky)

4. Specifikace

4.1. Wireless Numeric Keypad

Moc	6V DC (2x CR2032 Li battery)
Životnost baterie	Approx. 2 years (based on 4 operations/day)
Frekvence	433.92MHz +/- 75KHz
Výkon vysílače	1 mW
Formát dat	Norma
Provozní teplota	-20°C až +55°C
Password Number	0-8 číslic
Vodotěsná úroveň	IP54
Rozměry	85 x 75 x 35 mm
Hmotnost	150 g

4.2. 433MHZ Receiver

Napájení	12V-24V DC
Frekvence	433.92 MHz
Kódy	Fixed/Learning/Rolling codes compatible
Kanály	2 kanál
Provozní teplota	-40°C až +80°C
Rozsah recepce	10-50m (Built-in Aerial antenna)

4.3. 433MHZ Remote Control

Materiál	Plast + kov
Provozní frekvence	433.92 MHz
Používání	For 433Mhz RF receiver 1527 decode
Kompatibilita	Supports learning code (1527) receivers only. Not a clone remote.

5. Nastavení

5.1. Keypad Battery Installation

The keypad requires two CR2032 Li batteries. To install or replace them:

1. Vyhledejte přihrádku na baterie na zadní straně klávesnice.
2. Open the battery rear cover.
3. Insert two CR2032 batteries, ensuring correct polarity.
4. Close the battery rear cover securely.

5.2. Zapojení přijímače

Connect the receiver to your automatic door/gate opener system according to the following terminal definitions:

• MRAVENEC: přijímač Anténa
• CH1: Reléový výstup 1
• CH2: Reléový výstup 2
• V+: svtage + (12V-24V DC power supply)
• GND: Země

5.3. Pairing Remote Control with Receiver

To program a new remote control to operate your garage door or gate:

1. Press and release the yellow round button on the opener (or the 'LEARN' button on the receiver board). The learn indicator light (blue LED) will glow steadily for approximately 30 seconds.
2. Within these 30 seconds, press and hold the desired button on the hand-held remote that you wish to use to operate your garage door/gate.
3. Release the button on the remote when the opener light blinks once, or the blue LED on the receiver goes out. The new remote is now programmed.

5.4. Pairing Keypad with Receiver

To program the wireless numeric keypad with the receiver:

1. Long press the 'LEARN' button on the receiver board until the blue LED lights up.
2. On the keypad, enter the original password (e.g., '11' for left channel or '22' for right channel, as indicated in the video demonstration).
3. The blue LED on the receiver will go out, indicating a successful match.

Note: Refer to the video demonstration for a visual guide on the pairing process.

6. Návod k obsluze

6.1. Pomocí dálkového ovládání

Once paired, press the programmed button on your remote control to activate the connected garage door or gate opener.

6.2. Using the Wireless Numeric Keypad

To operate the connected device using the keypad:

1. Zadejte naprogramované heslo na klávesnici.
2. Press the appropriate channel button (e.g., 'left arrow' or 'right arrow' depending on the channel programmed) to activate the opener.

The keypad is a dual-channel transmitter, meaning it can control two separate devices or functions with different combinations.

7. Údržba

7.1. Keypad Battery Replacement

If the keypad's performance degrades or it stops responding, the CR2032 batteries may need replacement. Follow the steps in Section 5.1 for battery installation.

7.2. Čištění

Otřete zařízení měkkým, suchým hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla.

8. Řešení problémů

• Zařízení nereaguje: Check battery levels in the keypad/remote. Ensure the receiver is powered correctly. Re-attempt the pairing process.
• Omezený dosah: Ensure the receiver's antenna is unobstructed. Check for sources of interference (e.g., other wireless devices, metal structures).
• Chyba párování: Ensure you are following the pairing steps precisely. The timing for pressing buttons during the learning phase is crucial.

9. Uživatelské tipy

• For optimal performance, ensure the keypad is mounted in a location with good line-of-sight to the receiver, especially for outdoor installations.
• The keypad is suitable for 95% of garage door openers worldwide.
• The keypad's estimated transmission range is 200m in open space and 35m indoors.
• The system is compatible with various smart home platforms, including Tuya, Smart Life, Google Assistant, and Amazon Alexa, allowing for integrated control.
• The keypad is designed for utmost security, with transmitted codes changing at each session.
• This system is compatible with Nice OXI poa1 portals.

10. Záruka a podpora

All products come with a 1-year warranty from the store. For technical support or warranty claims, please contact the seller directly. Ensure you retain your purchase receipt as proof of purchase.

For additional information, you may refer to the Uživatelská příručka (PDF).

11. Certifikace

This product is certified with:

• CE
• RoHS