1. Úvod
This manual provides detailed instructions for the installation, programming, and operation of your Scimagic-RC SCS SENTINEL 433MHz Universal Garage Door Receiver. This 2-channel receiver is designed to work with a wide range of 433.92MHz remote controls, including fixed, learning, and rolling codes, making it a versatile solution for controlling garage doors, gates, and other automation systems.
2. Specifikace
| Funkce | Specifikace |
|---|---|
| Napájení | 12V-24V DC |
| Frekvence | 433.92 MHz (433 MHz) |
| Kompatibilita kódu | Fixed code (2262, 2260, 2264, 5326, M1E, M5E etc.), Learning code (1527, 2240, 6P20B, 6P20D etc.), Rolling code (HCS301, HCS300, HCS200, HCS201, HSC100, HCS1O1 etc.) |
| Kanály | 2 kanál |
| Pracovní teplota | -40 ℃ až +80 ℃ |
| Rozsah recepce | 10-100m (Built-in Aerial antenna) |
| Rozměry | 8.8 cm x 5.5 cm x 2.8 cm (přibližně) |
| Materiál | Kov a PVC |
2.1. Remote Control Specifications (Example)
| Funkce | Specifikace |
|---|---|
| Provozní frekvence | 433 MHz |
| Moc | 23A 12V Battery (Not included) |
| Materiál | PVC |
| Tlačítka | 4 tlačítek |
| Typ kódování | Kód učení |
| Přenosová vzdálenost | 20-50 m |
3. Obsah balení
Po otevření balíčku se prosím ujistěte, že jsou všechny položky přítomny a v dobrém stavu:
- 1 x Universal 433MHz Garage Door Receiver
- 1 x Návod k obsluze v angličtině
4. Nastavení a zapojení
The receiver features two channels (CH1 and CH2) for controlling two separate devices. Ensure the power supply is disconnected before making any wiring connections.
4.1. Popis Pinout
- MRAVENEC: přijímač Anténa
- CH1: Relay Output 1 (Connects to the device to be controlled by channel 1)
- CH2: Relay Output 2 (Connects to the device to be controlled by channel 2)
- V+: Pozitivní svtage Input (12V-24V DC)
- GND: Země
4.2. Schéma zapojení
Connect the receiver to your motor or controller as shown in the diagram below. The CH1 and CH2 relay outputs will activate the connected devices.
5. Programování a provoz
The receiver operates in a momentary working model, meaning the relay activates only while the remote button is pressed.
5.1. Learning Transmitter Codes
To program a new remote control to the receiver:
- Press either the "learn 1" or "learn 2" button on the receiver board for approximately 1 second. The "learn_led" light on the receiver will illuminate.
- While the "learn_led" is lit, press the desired button on your remote control.
- Continue holding the remote button until the "learn_led" on the receiver flashes and then turns off. This indicates that the transmitter's code has been successfully stored.
- Repeat these steps for any other remote controls you wish to program.
5.2. Ermasing Transmitter Codes
To clear all stored remote control codes from the receiver:
- Press and hold either the "learn 1" or "learn 2" button on the receiver board.
- Continue holding the button until the "learn_led" light illuminates and then goes out. All previously stored transmitter codes will now be erased.
6. Uživatelské tipy
- Vzdálená kompatibilita: This receiver is highly compatible. It can learn both fixed and rolling code 433.92MHz remote controls simultaneously.
- Duální ovládání: Utilize the two independent channels to control two different gate automations or alarm systems with a single receiver.
- Rozsah signálu: For optimal reception, ensure the receiver's antenna is not obstructed and is positioned for best line-of-sight to the remote control. The reception range is typically 10-100m.
- Napájení: Always use a stable 12V-24V DC power supply to ensure reliable operation.
7. Řešení problémů
- Receiver not responding: Check the power supply connections (V+ and GND) to ensure they are secure and providing the correct voltage (12V-24V DC).
- Remote not programming: Ensure the remote control is operating at 433.92MHz and is compatible (fixed, learning, or rolling code). Make sure to press and hold the remote button until the "learn_led" on the receiver flashes and turns off. Try clearing all existing codes and reprogramming.
- Snížený rozsah: Check the receiver's antenna for any damage or obstructions. Ensure there are no major metallic objects or strong interference sources between the remote and the receiver.
- Přerušovaný provoz: Verify all wiring connections are tight and free from corrosion. Ensure the power supply is stable.
8. Údržba
The SCS SENTINEL receiver is designed for low maintenance. Keep the unit clean and free from dust and moisture. Periodically check wiring connections for security and integrity. Avoid exposing the unit to extreme temperatures or direct water contact.
9. Záruka a podpora
For any issues or support needs, please contact the manufacturer or your point of purchase. Refer to the original packaging or product documentation for specific warranty terms and contact information.
Výrobce: ShenZhen Scimagic Development Technology Co.,Ltd
Adresa: Gebu Building 1406, Songgang, Baoan Shenzhen, China.
A PDF version of this user manual is available for download. View Uživatelská příručka (PDF)