
CreatBot PEEK-250
User manual
English V1.0
Henan Creatbot Technology Limited
PEEK-300 3D Printer
Icon conventions
Tip icon to remind users to have a good method or technique.
Note icon, to remind the user must be given adequate attention.
Prohibition icons, prevents users from unauthorized operation.
Notice
Read First
Thank you for choosing CreatBot 3D printer!
This manual contains important information about the installation, use, maintenance and common problems of CreatBot 3D printer. Please read this manual carefully before using 3D printer. All losses caused by the breach of the notes and the operation process of the operation process will be borne by the user.
Please use the filament provided by CreatBot, or high quality filament by third manufacturers. Due to the use of third party inferior material caused by the failure of the printer, the loss will be borne by the user.
Software running environment, 2G or above processors, at least 1G memory, compatible with Windows, MAC, or Linux, please use memory as much as possible.
I wish you have fun with CreatBot 3D printer!
Danger Warning
The nozzle’s temperature will reach 420 degrees, don’t touch.
The platform’s temperature will reach 100 degrees, don’t touch.
Please make sure that the printer connected to the ground.
Do not attempt to open the case, be careful of electric shock.
Working Environment
The 3D printer can work in the indoor environment of 5 ℃ to 30 ℃.
Long-term not use of the printer, be sure to keep off dust, moisture.
Long-term not use of the filament, please be sealed to prevent deterioration.
Machine Diagram



Printer Operation

- Turn on printer.
- Click “Move” > “All home” on the screen.
- Move the extruder by hand to 4 corners of bed, and check the distance between nozzle and bed. Tighten or loosen 4 adjusting nuts below the bed to make sure the distance between nozzle and bed is around 0.1mm with feeler blade or approximately the thickness of one business card in all corners to ensure the bed is Leveled.
Printer Operation

- Preheat nozzle.
- Straighted filament and check the filament do not self-winding.
- Thread the filament through the filament sensor and manually load the filament until it into the extruder.
- Click “Load”, until the filament come out from the nozzle.
- Click “Done”.

- Enter “ Filament” menu, click “Unload” .
- Wait for the nozzle heated to the suitable temperature.
- After reaching temperature, extruder will extrude a little filament, then unload the filament from extruder.
- Pull the filament out of the tube.
Main Menu
Touch screen

| Touch and set up the temp of the nozzle. 210°C Preset nozzle temperature 25°C Current nozzle temperature |
|
![]() |
Touch and set up the temp of the hotbed .110°C Current platform temperature 45°C Preset platform temperature |
![]() |
Touch and set up the temp of the Chamber. 70°C Current Chamber temperature 25°C Preset Chamber temperature |
Main Menu
Touch screen
Detail page

Axis operation
Filament menu
SD Card/U-disk

Info. page
Setting menu

The values in the picture are not real values, the real values refer to the printer default values
Setting menu

sink fan speed (range:1-100)
cooling fan speed (range:1-100)
head temperature (range:0-420)
hotbed temperature (range:0-100)
Setting menu

Enter the WiFi name and password, and click Connect. The printer will automatically connect to WiFi.
Only supports 2.4GHz Wi-Fi.
Frequently Asked Questions
Hardware Troubleshoot
The environment is too low, or temperature sensor is damaged, please keep the room temperature above 0℃ . 3. USB connection problems ? 4. Nozzle heats up too slowly ? 5. Print head stuck ? 6. Print head can not move ? 7. Print head hit the framework ? 8. Unable to power on ?
Printing Troubleshoot
1. How to set the temperature of the nozzle ? 2. How to set the temperature of the hot bed ? 3. The model not stick on the platform ? 4. No or less silk coming on the first layer ? 5. Why nozzle is not spit silk ? 6. How to prevent model become warped ? 7. How far from nozzle to platform appropriate ? 8. How to determine whether the temperature is too high ? 9. What reasons will causing nozzle blocked ? 10. Model surface is loose with crack ? 11. How to print a small model ? 12. Dual color model not aligned ? 13. Dual color model color interference ? 14. There is too much silk drag on the model ?
Henan Creatbot Technology Limited
Website: www.CreatBot.com
Email: sales@creatbot.com
Address: No.150 Lamei Road,
Zhongyuan District,
Zhengzhou City, Henan Province, China
Documents / Resources
![]() | PEEK-300 3D Printer |
References
- Large-scale & High performance 3D printers | CreatBotwww.creatbot.com
- User Manualmanual.tools


