CreatBot PEEK-250 High Performance Printer User Manual

CreatBot-logo

CreatBot PEEK-250 High-Performance Printer

CreatBot-PEEK-250-High-Performance-Printer-fig-1

Product Specifications

  • Model: CreatBot PEEK-250
  • Manufacturer: Henan Creatbot Technology Limited
  • Working Temperature: Nozzle – up to 420 degrees, Platform – up to 100 degrees
  • Working Environment: 5 to 30 degrees Celsius

Product Usage Instructions

Working Environment
The 3D printer can operate in an indoor environment with a temperature range of 5 to 30 degrees Celsius. Ensure to keep the printer away from dust and moisture when not in use for an extended period. Seal filament properly when not in use to prevent deterioration.

Printer Operation – Leveling Platform

  1. Turn on the printer.
  2. Click on Move > All Home on the screen.
  3. Manually move the extruder to the four corners of the bed and adjust the distance between the nozzle and bed by tightening or loosening the adjusting nuts below the bed. The distance should be around 0.1mm or approximately the thickness of one business card in all corners.

Printer Operation – Load Filament

  1. Preheat the nozzle.
  2. Straighten the filament and ensure it is not self-winding.
  3. Thread the filament through the filament sensor and manually load it into the extruder.
  4. Click Load until the filament comes out from the nozzle, then click Done.

Printer Operation – Unload/Change Filament

  1. Enter the Filament menu and click Unload.
  2. Wait for the nozzle to heat to a suitable temperature.
  3. After reaching temperature, extrude a little filament and then unload it from the extruder.
  4. Pull out the filament from the tube.

Printer Operation – Main Menu
In the main menu on the touch screen, you can set up various functionalities including preheating, cooling down, filament management, axis movement, and other settings.

Frequently Asked Questions

  • Hardware Troubleshoot
    If you encounter hardware issues, please refer to the troubleshooting section in the manual or contact customer support for assistance.
  • Printing Troubleshoot
    If you face difficulties during printing, check for common issues like filament jams, bed leveling problems, or software settings. Refer to the troubleshooting guide or contact customer support for help.

Notice

Read First
Thank you for choosing the CreatBot 3D printer!

  • This manual contains important information about the installation, use, maintenance, and common problems of the CreatBot 3D printer. Please read this manual carefully before using a 3D printer. All losses caused by the breach of the notes and the operation process of the operation process will be borne by the user. Please use the filament provided by CreatBot, or high-quality filament by third manufacturers. Due to the use of third-party inferior material caused by the failure of the printer, the loss will be borne by the user.
  • Software running environment, 2G or above processors, at least 1G memory, compatible with Windows, MAC, or Linux, please use memory as much as possible.
  • I hope you have fun with the CreatBot 3D printer!

Danger Warning

  • The nozzle’s temperature will reach 420 degrees, don’t touch it.
  • The platform’s temperature will reach 100 degrees, don’t touch.
  • Please make sure that the printer is connected to the ground.
  • Do not attempt to open the case, be careful of electric shock.

Working Environment

  • The 3D printer can work in the indoor environment of 5 ℃ to 30 ℃.
  • Long-term not use of the printer, be sure to keep off dust, and moisture.
  • Long-term not use of the filament, please be sealed to prevent deterioration.

Machine Diagram

Front

CreatBot-PEEK-250-High-Performance-Printer-fig-2

Rear

CreatBot-PEEK-250-High-Performance-Printer-fig-3

Extruder

CreatBot-PEEK-250-High-Performance-Printer-fig-4

Printer Operation

Leveling Platform

  1. Turn on the printer.
  2. Click “Move” > “All home” on the screen.
  3. Move the extruder by hand to the 4 corners of the bed, and check the distance between the nozzle and the bed. Tighten or loosen 4 adjusting nuts below the bed to make sure the distance between the nozzle and the bed is around 0.1mm with a feeler blade or approximately the thickness of one business card in all corners to ensure the bed is Leveled.CreatBot-PEEK-250-High-Performance-Printer-fig-5

Load Filament

  1. Preheat nozzle.
  2. Straight filament and check the filament does not self-winding.
  3. Thread the filament through the filament sensor and manually load the filament until it into the extruder.
  4. Click “Load”, until the filament comes out from the nozzle.
  5. Click “Done”.CreatBot-PEEK-250-High-Performance-Printer-fig-6

Unload/Change Filament

  1. Enter the “ Filament” menu, and click “Unload”.
  2. Wait for the nozzle heated to the suitable temperature.
  3. After reaching temperature, the extruder will extrude a little filament, and then unload the filament from the extruder.
  4. Pull the filament out of the tube.CreatBot-PEEK-250-High-Performance-Printer-fig-7
Touch screen

Main Menu

CreatBot-PEEK-250-High-Performance-Printer-fig-8
CreatBot-PEEK-250-High-Performance-Printer-fig-9
CreatBot-PEEK-250-High-Performance-Printer-fig-10

Detail page

CreatBot-PEEK-250-High-Performance-Printer-fig-11

Axis operation

CreatBot-PEEK-250-High-Performance-Printer-fig-12

Filament menu

CreatBot-PEEK-250-High-Performance-Printer-fig-13

SD Card/U-disk

CreatBot-PEEK-250-High-Performance-Printer-fig-14

Info. page

CreatBot-PEEK-250-High-Performance-Printer-fig-15

Setting menu

  • The values in the picture are not real values, the real values refer to the printer’s default values.CreatBot-PEEK-250-High-Performance-Printer-fig-16
  • sink fan speed (range:1-100)
    cooling fan speed (range:1-100)CreatBot-PEEK-250-High-Performance-Printer-fig-17
  • head temperature (range:0-420)
    hotbed temperature (range:0-100)CreatBot-PEEK-250-High-Performance-Printer-fig-18
  • Enter the WiFi name and password, and click Connect. The printer will automatically connect to WiFi.
    Only supports 2.4GHz Wi-Fi.CreatBot-PEEK-250-High-Performance-Printer-fig-19

Frequently Asked Questions

Hardware Troubleshoot

  1. Display “MINTEMP”?
    If the environment is too low, or the temperature sensor is damaged, please keep the room temperature above 0℃.
  2. Display “MAXTEM P” temperature ofofof the nozzle or bed is too high, temperatureseure sensor is damaged, please keep their temperature within a suitable range.
  3. USB connection problems?
    Please specify the correct port and baud rate (250000), or change a shorter USB cable.
  4. Nozzle heats up too slowly?
    Temperature in the door is too low, use a fan duct, or turn up the output voltage (24.5v).
  5. Print head stuck?
    Clean the guide rail and add lubricating oil.
  6. PriThe printad can not move?
    Stepper motor chipset burned, belt damaged, or belt wheel screw loose.
  7. Print head hit the framework?
    Corresponding axis stop limit or circuit fault.
  8. Unable to power oit n?
    Power switch is damaged or fusthe e is burnanddase check whether the power adapter is working properly or how the er check board is damaged.

Printing Troubleshoot

  1. How to set the temperature of the nozzle?
    Different filament temperatures are different, generally as follows:
    • PLA temperature 190℃~210℃, bed 45-60℃.
    • ABS temperature 230℃~250℃, bed 80-100 ℃.
      You must leave enough time for filament heating, so the faster the printing speed the temperature, 60the mm/s temperature needs to rise about 10℃. In the same way, larger thicknesses need higher temperatures.
  2. How to set the temperature of the hotbed?
    The main purpose of the hotbed is to prevent model wrapped, PLA needs about 45℃ and 70℃ for ABS is enough, but due to the environment and filament, we often need to increase the temperature, the highest temperature not over 120℃, and you can close the bed above 100mm except printing ABS or other high-temperature required filaments.
  3. Does the model not stick on the platform?
    Please paste masking paper or Kapton tape on the platform, or the nozzle is too far away from the platform, or the bottom of the model is not flat.
  4. No or less silk coming on the first layer?
    The distance between the nozzle and the platform is too small, or the filament has not been sent to the nozzle.
  5. Why nozzle is not spit silk?
    The filament is not pressed or too tight, or the print temperature is too low, or the filament feeder not working.
  6. How to prevent the model become warped?
    Increase hot bed temperature using Kapton, change platform adhesion type to Raft, cover the baffle, or reduce indoor ventilation.
  7. How far from the nozzle to the platform is appropriate?
    Distance should be 0 in theory, but there is no flat platform, so the distance should be +-0.1mm. Finally, with the actual printing effect as the standard, too close will lead to a silk blocked, and too far will cause the model not to stick on the platform.
  8. How to determine whether the temperature is too high?
    PLA temperature is too high will appear liquefaction, ABS will be the carbide, that will block the nozzle.
  9. What reasons will cause the nozzle blocked?
    Filaments are impurities or print environment dust too mucandand d thermal conductivity between the nozzle and the heating block.
  10. The model surface is loose with a crack?
    The layer is too high the printing speed is too fast, the nozzltemperatuiss urisoo low, or filament press nut is too loose, or the filament is wrapped.
  11. How to print a small model?
    Multiple the model, and print them at a time.
  12. Is the dual-color model not aligned?
    Adjust the offset of the second nozzle in machine settings.
  13. Dual color model color interference?
    Align two nozzle in the vertical direction
  14. The..re is too much silk drag on the model?
    Please enable filament retraction, and specify the retract speed and distance, the retract distance shobenbe less e  than 4mm, and the speed not less than 10mm/s.

ABOUT COMPANY

Documents / Resources

PDF thumbnailPEEK-250 High Performance Printer
User Manual · PEEK-250 High Performance Printer, PEEK-250, High Performance Printer, Performance Printer, Printer

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.