IB518183ML HLA4 4 Inch Round and Square LED Directional Fixture Fitting
HLA4 – 4” Round & Square LED Directional Fixture Fitting
Packaging Contents
ITEMS REQUIRED
(Purchase separately)
• Gloves
Selector Switch (2700K, 3000K, 3500K, 4000K, 5000K)
Choose your favorite correlated color temperature
(CCT) from 5 options using the switch
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
- Heed all warnings, including below warnings AND those included on product.
- HALO® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.
Risk of Fire – MINIMUM
90°C SUPPLY CONDUCTORS.
If uncertain, consult an
electrician.
Risk of Electric Shock
– To avoid possible electrical
shock, be sure that power
supply is turned off at
fuse box or circuit breaker
before installing or servicing
luminaire.
Risk of Fire/Electric
Shock – LED DM fixture
installation requires
knowledge of luminaires
electrical systems. If not
qualified, do not attempt
installation. Contact
a qualified electrician.
Luminaire wiring and
electrical parts may be
damaged when drilling
for installation of LED DM
fixture. Check for enclosed
wiring and components.
• Install this kit only in the luminaires that have the construction
features shown in the photographs and/or drawings.
• To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
Edges may be Sharp – Wear gloves while handling.
- Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
- Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
- This device is not intended for use with emergency exits.
- For Canada only per CSA C22.2 No. 250.1-16, retrofits for luminaire conversion: The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations.
DIMMING
Halo HLA is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information. Note some dimmers require a neutral in the wallbox.) For the latest Halo HLA product information, please refer to specifications online at www.cooperlighting.com.
DETERMINING WHICH INSTALLATION METHOD TO USE
The HLA models can be installed directly into a ceiling without requiring separate JBOX or recessed housings. boxes
1. Cut an opening in the ceiling by using the provided template to trace the module opening (see Figure 1). Make sure the opening is not larger than the outer flange of the LED module. A hole saw is recommended.
Risk of Electric Shock –
• To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.
WIRING
2. Open the cover of the provided jbox and insert the supply wires through the preferred strain reliefs in the provided jbox (Fig. 2a). Connect the bare copper (ground) wire from the jbox to the ground wire of the supply connection using the provided wire nut (see Fig. 2b).
3. Connect the black/white leads from the input of the driver to the appropriate supply side wiring using the provided wire nuts.
4. Close the cover after properly securing the supply wire to the provided jbox on the rear of the LED module.
5. Module is ready to install into ceiling. (See MOUNTING section for specific instructions).
MOUNTING
- Connect the remote driver box to the light fixture. (Fig. 3a)
- Place remote driver box thru the cut-out hole and mount according to local code as required. (Fig. 3b)
- Bundle any excess wire and place into ceiling above the module according to local code as required.
- Rotate both mousetrap springs upward to allow passage through the cutout in the ceiling (Fig.4).
- Continue to press the module through the cutout in the ceiling until the perimeter flange of the module is flush against the ceiling.
- The springs will rotate back into position and hold the LED module tight to the ceiling.
Note: For use with new construction mounting frame, insert jbox into ceiling hole and slide box into position (see Fig. 3C).
AIMING
1. Tilt the fixture towards a desired target (Fig. 5).
Risk of pinching –
Do not place hands or fingers under springs during removal of the LED module.
- Simply and slowly pull down firmly on LED module until mousetrap springs release from the ceiling. Reach through the ceiling to hold mousetrap springs up and away from the ceiling as you continue to pull the module from it’s opening.
- Disconnect wiring.
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
5-YEAR LIMITED WARRANTY
Limited warranty for five years, based on up to 6 hours of usage per day.
Additional terms and conditions apply.
For more details, please visit:
www.cooperlighting.com/warranty
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2024 Cooper Lighting Solutions
All Rights Reserved
Printed in China
Imprimé en Chine
Impreso en China
Publication No. IB518183ML
Cooper Lighting Solutions is a registered trademark. All trademarks are property of their respective owners. Product availability, specifications, and compliances are subject to change without notice.
HLA Series Instructions
www.halolighting.com
Documents / Resources
 |
COOPER IB518183ML HLA4 4 Inch Round and Square LED Directional Fixture Fitting [pdf] Instructions IB518183ML, IB518183ML HLA4 4 Inch Round and Square LED Directional Fixture Fitting, IB518183ML, HLA4 4 Inch Round and Square LED Directional Fixture Fitting, Inch Round and Square LED Directional Fixture Fitting, Round and Square LED Directional Fixture Fitting, Square LED Directional Fixture Fitting, LED Directional Fixture Fitting, Directional Fixture Fitting, Fixture Fitting, Fitting |
