Coomotech Ice Maker Instruction Manual

Coomotech Ice Maker

INSTRUCTION MANUAL

This ice maker produces ice cubes and temporarily stores ice in the unit’s storage tank. Follow safety and installation requirements, connect potable water and a properly routed drain line (so melted ice can flow out), then use the control panel buttons for power, cleaning, and light/interval settings.

Support Email: help@coomotech.com

It is important that you read these instructions carefully and keep it for future reference.The picture is for reference only. Please be subject to the actual products.

Quick Setup & Use

1. Unpack the unit and remove all exterior/interior packaging materials; check package contents.
2. Recommended: leave the ice maker for 24 hours after unpacking.
3. Clean the interior with lukewarm water and a soft cloth, or run the Self-Clean function.
4. Place the ice maker on an even, flat surface in a well-ventilated indoor location, away from direct sunlight and heat sources, with at least 15 inches clearance to the walls.
5. Connect water using a potable/drinking-water source meeting local standards; ensure water pressure is 0.1–0.4 Mpa (use a pressure reducing valve if above 0.4 Mpa).
6. Connect the drainage pipe before using: connect one end to the machine and route the other end to a container/sewer; keep the other drain port lower than the machine’s drain port.
7. Allow 1 hour for the refrigerant to settle before initial use; position the unit so the plug is accessible.
8. To start: in standby mode, press the ON/OFF button briefly.
9. To clean before use or after long downtime: run Self-Clean using water + vinegar or lemon juice (1:1), then hold ON/OFF for ~3 seconds to start; when finished, unplug and drain, then dry; repeat once to rinse out residue.
10. To take ice cubes: wash hands, use the provided plastic ice scoop, close the door after taking ice, and avoid putting anything else in the machine.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock , and injury to persons or property. Read all instructions before operating the machine for the first time.

CAUTION: ICE CAN’T BE STORED IN THE ICE BIN DURING NIGHT-TIME, IT’S NOT FRIDGE, ICE WILL BE MELTED TO WATER AND FLOW OUT OF THE MACHINE.

1. If connect with water supply, CAUTION: must connect the potable water supply;
2. The machine is intended to be used in household and similar applications such as:
– staff kitchen areas in shops, offices, and other working environments;
– farmhouses
– by clients in hotels, motels, and other residential type environments;
– Catering industry and similar industries.
3. The machine should be used indoors and without obstacles surrounded good ventilation place. There is must be 15 inches at least between the four sides of the machine with the wall.
4. When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock , and injury to persons or property. Read all instructions before using any appliance.

5. Don’t operate this or any other appliance with a damaged cord.
6. Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the socket.
7. Don’t place the machine and power cord near flammable material. Do not cover the cord. Do not submerge it in water.
8. We do not recommend the use of an extension cord, as it may overheat and become a risk of fire.
9. Unplug the ice maker before cleaning or making any repairs or servicing.
10. Exercise caution and supervision when the appliance is used near children.
11. Don’t use your ice maker outdoors. Avoid direct sunlight and make sure that there is at least 15 inches of space between the back and sides of your unit and the wall.
12. Don’t use any liquid other than water in the unit to make the ice.
13. Do not clean your ice maker with flammable detergents.The fumes can create a fire hazard or explosion.
14. Do not tip the machine over.
15. If the ice maker is brought indoors from outdoors during the wintertime, give it a few hours to warm up to room temperature before plugging into the power source.
16. This unit should be properly grounded for your safety. The power cord is equipped with a three-prong plug mated with standard three-prong wall outlets to minimize the possibility of electric shock.
17. Plug your appliance into a dedicated, properly installed, and grounded wall outlet. Do not, under any circumstance power and /or grounding should be directed toward a certified electrician.

18. The foaming materials inside are combustible which must be kept away from fire.
19. It’s forbidden to pull the cable to unplug the plug, pull the plug is a must.

IMPORTANCE: To avoid hazards due to instability,the unit must be placed on an even and flat surface.

WARNING: This appliance must be grounded.

Warning: Combustible materials

1) The fuse on the PCB is 15A,if change,must be operated by a technician.
2) voltage fluctuation can’t be exceeded ±10% than the rated voltage,or a Voltage stabilizer is needed.
3) In addition to the method recommended by the manufacturer, mechanical equipment or other methods must not be used to accelerate the defrosting process, and the refrigeration system must not be damaged.
4) The refrigeration system contains high-pressure refrigerant, and the refrigeration system must not be damaged. Be especially careful when installing and moving. Installation and maintenance must be performed by the manufacturer or professional. Scrap must be disposed of by the designated recycling department.
5) There are heat insulation materials in the appliance, which are combustible materials, and must be kept away from fire sources. Repairs must be performed by the manufacturer or professionals. Scrap must be disposed of by the designated recycling department.

IMPORTANCE: To avoid hazards due toinstability, the unit must be placed on an even and flat surface.

Installation and connection

Note: The installation must be carried out by professionals according to the instructions.

UNPACKING YOUR ICE MAKER

1. Remove all exterior and interior packaging materials. Check whether all the below accessories are included or not. If any parts are missing, please contact our customer service. After you unpack the machine, we recommend you to leaving it for 24 hours before turning it on.
2. Clean the interior with lukewarm water and a soft cloth or clean the unit using the Self-Clean function.
3. Find a location for your ice maker where it’s protected from direct sunlight and other sources of heat (i.e. stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at least 15 inches of space between the back and sides of your ice maker and the wall.
4. Allow one hour for the refrigerant to settle before plugging the unit for initial use.
5. The appliance must be positioned where the plug is accessible.

Package Contents

• Ice maker machine x 1

Warm Tips：.Check whether all below accessories are included.

INSTRUCTION STEPS

1. Place the machine on a flat place

2. Ways of adding water

Use bucketed water as a source of water

2.Ways of adding water

Use bucketed water as a source of water

3.Ways of adding water

Use water faucet as water source

3.Ways of adding water

Use water faucet as water source

4. Connect to drain pipe plug into the socket

5. Make Ice

Press ON/OFF button, the machine will workautomatically.

The place of installation

a) The appliance should be placed in a clean place with good ventilation, which should be kept from sunlight and rain.
b) The machine cannot be placed near any heat source.
c) The ambient temperature around should not be lower than 3C, not higher than 40°C, and there is must be 15 inches at least between the four sides of the machine with the wall.
d) The machine should be placed in a flat place.
e) Do not place anything on top of the appliance.

Connect drainage pipe and water intake pipe

Warning:

1)The machine can only connect with drinking water sources,and must meet local drinking water standards
2)The water pressure must be in 0.1-0.4Mpa,if exceed 0.4Mpa, a pressure reducing valve must be connected.
3) Drainage:The outlet of the drainage pipe must be lower than the outlet on the machine

CONNECTING WITH WATER

Please connect your ice maker with other parts by referring the diagram below.

Water Hose Connecting Guide

Step 1: Insert the water hose as much as you can, otherwise you might experience water leaking.

Step 2: Water hose successfully connected.

Drain:

Warning: Because the ice in the inner tank will melt, drain pipe must be connected before using, and insert the drain pipe into a container or into the sewer.

Note: Connect one end of the drain pipe to the machine, and the other end to a container or sewer. The other port of the drain pipe must be lower than the drain port of the machine.

MACHINE OPERATIONS

ON/OFF button:

In standby mode, press this button briefly (display”_”) to make the machine work, press for a long time to enter the cleaning state; during, press the button briefly to cut off the power of the machine, press for a long time to enter the defrost maintenance.

Reservation button:

In standby mode, press scheduled start, press again to set the cycle time; when the machine is on, press scheduled shutdown, press again to set the cycle.

Light button:

Press this button to turn off the blue light,press again to turn it on.

Notes:
The surrounding environmental temperature will influence the time needed for ice making.

Warning:

1. The appliance is used to make ice cubes and store ice temporarily . please follow the following principles to keep the ice cubes clean:

• Wash your hands before taking out the ice cubes and use the plastic ice scoop provided to take ice.
• Except ice cubes, please do not put anything else in the machine.
• Clean the storage tank before use. Keep the ice scoop clean and use a neutral detergent to clean it. Close the door after taking ice to prevent dust.

2. The use of any electrical appliances must follow basic guidelines, especially:

• A high humidity environment will increase the risk of short circuit or electric shock. If in doubt, please cut off the power of the machine.
• Please do not pull the power cord directly to turn off the machine.
• Without adult supervision, the ice maker cannot be used alone by children or the elderly.

CLEANING & MAINTENANCE

Please thoroughly clean your ice maker before initial use.

1) Cleaning of internal and external parts

Note: Unplug the power plug before doing any cleaning or maintenance procedures.

Clean the condenser at least once a year, so that the ice maker can work better.
Do not use alcohol to clean the ice machine, as this may cause the plastic to crack.

a)External

Use a clean soft cloth to wipe the ice machine at least once a week, and then use a soft cloth with a neutral detergent to remove grease or other impurities.

b) Ice scoop cleaning (weekly)

Dip the ice scoop in a mixture of neutral detergent and water for at least 3 minutes, then rinse with water.

c) Storage tank cleaning (weekly)

Open the ice door and remove all ice cubes.

Use a neutral detergent to clean the inner wall of the tank, and then rinse with water.

Wipe the inner wall with a cloth with neutral detergent, rinse with water, and finally dry the inner surface with another clean cloth.

INTERIOR: please use the following Self-Clean function:

1. Add water and vinegar or lemon juice mix (1 :1 ratio)
2. Plug in unit,press and hold the ON/OFF button for approximately 3 seconds,then release.The unit will automatically enter Self­clean program. This process takes about 5-6 minutes.When the Self-Clean program is finished,unit will automatically power off.
3. The fan blade will be rotating.This process rinses the inside parts several times.
4. After the Self-Clean program is completed,unplug the power cord and drain out the water by unplugging the drain cap on the side.Replace drain cap.
5. Plug the unit and repeat the Self-Clean process by repeating steps 3 to 5. This will rinse out the vinegar/lemon residue.
6. After draining the water,replace and tighten drain cap.

7. Dry the interior and exterior with a clean,soft cloth.

NOTE: It is strongly recommended to clean the unit before initial use or after the unit has not been in use for a long period of time.

2) Long-term storage of the ice maker

a) Unplug the power plug to cut off the power supply;
b) Turn off the water supply and remove the water inlet pipe;
c) Remove all ice cubes and drain the water ;
d) Wash and dry the inner walls of the storage tank and water tank.

Common malfunction analysis

E1

Temperature sensor short circuit or open circuit

This fault can make ice normally, but only shows when powered on.

Replace the sensor

E2

Display anomaly

Ice maker motor not running or evaporator sensor damaged

Replace the faulty components

E3

The fan is not work

The condenser prob is not sensitive The fan is jammed

Unplug the prob or replace by a new one Adjust the fan

Fan is broken

Replace by a new fan

E4/6

Ice full

The infrared through-beam tube is blocked.

Remove obstructions, or wipe the infrared receiving and emitting port with a tissue.

Troubleshooting

• E1 (Temperature sensor short/circuit/open circuit): If the display shows E1 when powered on, replace the sensor circuit or sensor.
• E2 (Display anomaly / motor not running or evaporator sensor damaged): Replace the faulty components.
• E3 (Condenser/fan issue): If the condenser probe isn’t sensitive, check/resolve the probe sensitivity; if the fan is not working or jammed, unplug and then either adjust the fan or replace the faulty fan; if needed, replace the fan.
• E4/6 (Ice full): This indicates the ice bin is full; address related conditions and ensure normal operation (if the fan is broken, replace it; if the infrared through-beam tube is blocked, remove obstructions or wipe the infrared receiving/emitting port with a tissue).
• General note: If you suspect an electrical issue in a high-humidity environment, cut off power of the machine.

Specifications

Power/Protection (PCB fuse)	15A (replacement must be performed by a technician)
Input voltage fluctuation limit	Not to exceed 10% of rated voltage (otherwise a voltage stabilizer is needed)
Operating environment	Indoor use only; place with good ventilation
Clearance requirement	At least 15 inches between the four sides of the machine and the wall
Ambient temperature range	Not lower than 3°C; not higher than 40°C
Water source	Connect only to drinking water sources that meet local drinking water standards
Water pressure range	0.1–0.4 Mpa (if above 0.4 Mpa, use a pressure reducing valve)
Drain routing	Drain pipe outlet must be lower than the outlet on the machine; connect drain pipe before using
Self-Clean function time	About 5–6 minutes per run