CoolGeek M1 Music Frame User Manual

Do not install near any heat source, such as radiator, heat accumulator, stove or other heating device.
Equipment (including power amplifier).
Prevent the power cord from being cut off. Do not touch the connecting wire at will.

Use only the accessories/fittings specified by the manufacturer.
All maintenance shall be carried out by qualified maintenance personnel.

Any damage to the equipment, such as damage to the circuit board, splashing of liquid, falling of objects, Maintenance is required in the equipment, when the equipment is exposed to rain or damp, or when it fails to operate normally or falls.
Repair.
Do not expose the equipment to water leaks or splashes. .

Do not place any source of danger on this equipment (for example, An object with a liquid, a lighted candle).
The battery (battery pack or combined battery) shall not be exposed to excessive heat such as sunlight, fire or the like.

In the environment.

The battery (battery pack or combined battery) shall be charged with the original compatible charger.

Warning

Do not lubricate any part of the machine. .

Do not place the device on top of other electrical equipment.
To prevent damage to the circuit board IC by static electricity, do not touch the circuit board with your hands.

Class | Laser Products

This product contains a low-power laser device. To ensure safe use, do not disassemble any Cover, or attempt to disassemble the inside of the product. Refer to qualified personnel for repair.

Enclosure

Host : 1
Remote control : 1

18650 battery : 1
Battery Charging : 1

Case: 1
Picture frame support bar : 2

Operating Manual : 1
Picture frame hook : 2

Picture frame hook screws : 4
Phillips screwdriver : 1

Host overview

Display screen
POWER – Switch button
PAIR – Bluetooth reset button
3.5MM audio output interface
Remote control induction probe
CD movement
Battery compartment
Acrylic transparent baffle
Front bezel notch
Embedded nut of support rod of photo frame
Photo frame hook
Picture frame support rod
Power
Pause/Play

Out of stock to chang disc
Volume
Part one-song

Bluetooth reset
Volume +
Next-song

Playback mode switch

Source

Removing battery
This machine has a removable rechargeable battery for operation.

In the boot state, if the battery power is low, on the display screen

Take the battery capacity grid as a reference.
Charge with a special charging case,
During charging, the charging box indicator light is on.

Fully charged, the charging case indicator is green

Note: It is recommended to use the attached battery charging box to charge the local battery.

battery status

Full rate : 75%-100%
3 case : 50% -75% of foot state
2 grids : 25%-50%

1 Grid : represents below 25% (low electric state

The screen battery logo is blank (space: indicates serious low power state, shut down at any time)

Turn on / off

Shutdown state, long press the POWER button on the local device for 3 seconds or click the power button on the remote control, boot the machine, the screen shows “OPEN” and the last selected sound source before shutdown first power up in CD Bluetooth mode
press and hold the local POWER button for 3 seconds or click the remote POWER button again the machine will switch to the shut down state and the display is off.
Shut down the machine automatically.
In any mode, without any operation for 5 minutes,

Disc operation

Supported disc format is as follows:

CD-DA/CD-R/CD-RW
MP3: Maximum sampling rate 48 KHz, bit rate 320 kbps
WMA: the highest sampling rate of 48 KHz, with a bit rate of 192 kbps

Play the disc

Displacement (outbound setting)
Click the local POWER key or long press the stop key 3S of the remote control, the screen shows “OPEN”, the movement stops the disc, then the disc can be replaced.

Change the disc

Click the local POWER key or long press the pause button for the remote control
There is a disc
After starting on, automatically start to enter the disc, the screen displays “CD–” means that the disc is being read, and the progress bar indicates the start of the disc;
No disc
When reading the disc, the screen displays “NODISC”, you need to put the disc, and then click the local POWER key or the pause key of the remote control to start the reading disc;

If the disc format is not supported, the machine stops turning the,
disc after the disc is in compatible, and needs to change the disc
When reading the disc until the last song of the disc plays, if the normal cycle mode is set, the disc stops reading,

Pick a track

last song.
Click the previous track button on the remote control and each time you do so, the track is decremented by |

next song.
Click the next track button on the remote control ,and increment the track by | for each action

Play/Pause

Click the pause button on the remote control to pause the playback and the track progress bar on the screen will stop;
When playback is restarted, the progress bar starts running again.

Fast forward/rewind

Press and hold the previous button on the remote control to rewind the play progress bar
Press and hold the Next button on the remote control to fast forward the playback progress bar

Volume adjustment.

Volume +: Click the + button on the remote control
Volume-: Click the-button on the remote control

Playback mode selection

Normal playback:
This machine defaults to this mode.
Single loop:
Click the A-B button on the remote control to select the single loop mode, and the screen will display the single loop Icon, the current song single is played in a loop.

All Cycles:
Click the A-B button on the remote control to select the full cycle mode, and the screen will display the full cycle
Icon, all the songs on the album are played in a loop.
Shuffle
Click the A-B button on the remote control to select the random mode, and the screen will display the random play image Mark, the song of the record is played randomly.

Disc song memory function

Original disc
When the machine plays the disc used last time and does not come out of the bin, when the machine is started to play again, The machine memorizes the last played track by default. (For example, after the fourth song is played last time, it is turned off, and when it is turned on again, At this time, the machine knows not to play the fourth song.)
new disc.
When the machine plays a new disc, the default is the first song.

Bluetooth & AUX Connection

Start the BT OUT mode automatically, and the blue light flashes, indicating entering the Bluetooth emission search state.

State, the Bluetooth indicator flashes, and the Bluetooth logo on the screen flashes.

Bluetooth pairing
Make sure that the Bluetooth device to be connected is in the Bluetooth-on state. When the Bluetooth connection is paired, The blue light is always on, the CD is played, the audio is output from the Bluetooth speaker device, and the Bluetooth indicator is always on After 5S, it will be turned off, and the Bluetooth logo on the screen will be always on.

Bluetooth back connection
The Bluetooth device has a connection record with the machine, and when the machine is powered on next time, the Bluetooth device is automatically connected back to the device;
The Bluetooth device has a connection record with the machine, but after the connection is disconnected beyond the distance, it is restored to a valid return connection
When the distance is short, the machine and the Bluetooth device will be connected again. If the connection fails after 5min, it will be automatic.
Shutdown.

Bluetooth reset
Click the PAIR button of the machine or the remote controller, the Bluetooth indicator light changes from normally on to flashing, and the screen is blue
The tooth logo changes from normally lit to flashing, and the Bluetooth disconnects the previously connected device and re-enters the search.
Pairing state of the cable.
AUX OUT connection
Connect the 3.5mm audio cable, and the audio is output from the 3.5 interface (synchronous output of Bluetooth audio signal)

Technical specifications

Lithium battery (internal) :3.7V/2600mAh (18650) xl
Distortion : ≤1% (IKHz, IW)
Product Dimensions : 318 (W) ×229 (H) x64 (D) mm
Encoder support : SBC
Disc supported formats : CD-DA/CD-R/CD-RW/MP3/ WMA

Bluetooth parameters
Bluetooth version : 5.0
The maximum communication distance is about : 10 meters.
Compatible with Bluetooth profiles : A2DP

If there is a problem with the system, please check the following items yourself before requesting a repair.
If the problem cannot be solved, please contact a qualified service station for repair.

No power

Make sure the battery is properly installed and connected to the system.

As a power-saving feature, when the track is at the end and no action is taken,
The system will automatically shut down after 5 minutes.

No disc detected

Put in the disc.

Check that the disc is facing out.
Wait for the condensation on the lens to dissipate.
Replace or clean disc.

Please use a closed disc or a disc of the correct format.

No sound

Adjust the volume.

Check whether it is in the suspended state.
In case of wireless output, make sure the Bluetooth device is connected;
In case of wired output, make sure that the cable functions properly and is in good contact with the socket.

The disc cannot be played

Place a readable disc with the printed side of the disc facing outward.
Check if the disc format is supported..

Check for scratches or smudges on the disc.
As a power-saving feature, when the track is at the end and no action is taken,
The system will automatically shut down after 5 minutes.

Music gets worse with a Bluetooth-enabled device
Bluetooth reception quality is poor. Move the equipment closer to the system or remove the equipment from the system
Any obstruction.

Unable to connect to this system

The device does not support the specification required by the system.
The Bluetooth device is too far away from the system to detect the signal.

The system is connected to another Bluetooth-enabled device.
Disconnect the device or all other connected
Device, and then try again.

COOLGEEK IS A REGISTERED TRADEMARK OF GEEKS TECH CO.,LTD
COOLGEEK SUBSCRIBES TO A PROGRAM OF CONTINUOUS IMPROVEMENT. AS A RESULT, SOME PRODUCT FEARURES AND CHARACTERISTICS MAY CHANGE WITHOUT PRIOR NOTICE.
Made in China

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.