CONQUER HKBTLEDMLD01 Wireless Speaker LED Lamp
Product Specifications:
- Model: HKBTLEDMLD01
- Type: Wireless Speaker LED Lamp
- Power Source: Type-C USB cable (5V/1A MAX 2A adaptor not included)
- Bluetooth Range: Up to 33 feet
- Lighting: LED Light
- Safety: Not suitable for children, keep away from water/heat
Product Usage Instructions:
Caution: This device is not a toy. Keep away from small children and water/heat sources.
Instruction Manual (Read before proceeding)
Power the Speaker
- Using a Type-C USB cable (included), insert the jack into the hole on the bottom part of units and then plug the USB connector in to the USB port on a computer or 5V/1A （MAX 2A）adaptor (not included)
- The LED indicator will light up RED while connect to power and turn off when disconnect to power.
Powering ON/OFF the Speaker
- Connect the power source
- Long press the button to power on the speaker. A tone will be heard and the speaker will enter Bluetooth paring mode. The speaker will automatically re-pair to any nearby previously paired devices.
- Long press the function button again to power off the speaker to power off the speaker.
Playing Music via Bluetooth
- Turn your Bluetooth speaker on by sliding the power switch located on the back of the speaker to ON position and long press the function button to activate the Bluetooth function.
- A tone will be heard and the speaker will enter Bluetooth pairing mode.
- Make sure the Bluetooth function on your device is turned on.
- Search the speaker named,” HKBTLEDMLD01”.
- The Bluetooth device does not find the Bluetooth device automatically After 5 minutes, the Bluetooth light is off, if you want to use Bluetooth, you must restart the boot.
- The lighting work is not affected when the Bluetooth is asleep.
- Start playing music on your device. Make sure that you keep your device within a 33 feet range of your Bluetooth speaker.
- Adjust the volume of your device to a comfortable level.
- Turn off the unit when not in use.
Using the Light
- short short-press the button to turn on the LED light
- Short-press the button again to turn off the light
Caution:
- This is not a toy. Please keep away from small children.
- Please keep away from water/heat.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet the general RF exposure requirement. The device can be used in portable exposure conditions without restriction
FAQs
Q: How do I reset the Bluetooth pairing on the speaker?
A: To reset Bluetooth pairing, power off the speaker, then power it back on and ensure your device’s Bluetooth is discoverable.
Q: What should I do if the LED light does not turn on?
A: Make sure the speaker is powered correctly and try pressing the light button again. If issues persist, contact customer support.
Documents / Resources
 |
CONQUER HKBTLEDMLD01 Wireless Speaker LED Lamp [pdf] Instruction Manual HKBTLEDMLD01, HKBTLEDMLD01 Wireless Speaker LED Lamp, Wireless Speaker LED Lamp, Speaker LED Lamp, LED Lamp |