connect2go Envisalink 4 C2GIP Internet Module

Product Information

• Product Name: Envisalink 4 (C2GIP)
• Power Draw: 70mA

Product Usage Instructions

Connect2Go Account Setup

1. Go to https://www.connect2go.com and select Dealer Signup to create a dealer account.
2. Log in to your dealer account.
3. Create a client.
4. Add the device to the client’s account using the 12-digit ID on the device.

Module Connection to Control Panel

1. Record the 12-digit ID from the sticker on the module.
2. Connect the module to the Tip/Ring terminals.
3. Connect an 8-conductor UTP cable with an RJ-45 connector to an available router, switch, or hub port with a DHCP server available.
4. Restore power to the system.

Panel Programming (Vista Panels)

For Vista panels, navigate to the Support page in your dealer account and follow the Instructions For Enrolling Honeywell Panels option.

Envisalink Local Access

1. To access the web interface on the module, from a browser on the same internal network, type ‘envisalink’ or the IP address of the module.
2. The default username is ‘user,’ and the default password is the last 6 digits of the MAC ID.

Expansion

To avail of additional ports, follow the LED descriptions provided in Table 1.

NOTE: For Honeywell users, it is important that you create the user’s Connect2Go account and activate the module on the account before you connect it to the panel. Connect2Go Account For Website & Mobile Access

INSTALLATION

1. Go to https://www.connect2go.com, navigate to the bottom of the and select Dealer Signup to create a dealer account.
2. Log in to your dealer account.
3. Create client.
4. Add the device to the client’s account using the 12-digit ID on the device.
5. For more detailed instructions, from inside your dealer account, navigate to the Support page and select Start with this Step-by-Step Dealer setup guide at the

To Connect The Module To The Control Panel
Note: Before installing record the 12 digit ID from the sticker on the module. You will need it during activation.

1. Disconnect power from the panel.
2. Connect the module to the Keypad bus terminals of the panel. Caution: Do not connect the module to the Tip/Ring terminals, or you may damage the device.
3. Connect an 8-conductor (not supplied) UTP cable with an RJ-45 connector to an available router, switch, or hub port with a DHCP server available.

Restore power to the system.
NOTE: On DSC systems, the Envisalink 3 automatically enrolls with the security system as PC5400/DVACS module Panel Programming (Only for Vista panels. Not required for DSC panels)

1. From inside your dealer account, navigate to the Support page and choose the Instructions For Enrolling Honeywell Panels option. Envisalink Local Access
2. To access the web interface on the module, from a browser on the same internal network type “envisalink” or the IP address of the module.
3. The default username is “user”, and the default password is the last 6 digits of the MAC ID

LED Descriptions

Table 1 : LED Descriptions

Name	Description
OPER	SOLID GREEN – Power and functioning. OFF – Not functioning or not powered properly.
KEYB	SOLID GREEN – Panel connected correctly FLASHING – Panel not connected (DSC firmware installed) OFF – Panel not connected (Honeywell firmware installed)
NET	SOLID GREEN – IP obtained through DHCP FLASHING – Module programmed to static IP OFF – Module cannot obtain IP from DHCP server (router)
ONLINE	SOLID GREEN – The Module is communicating with servers and the account Is properly set up. FLASHING – Module is communicating with servers but no account _exists.
	OFF – The Module is not communicating with servers.
LINK	SOLID GREEN – Ethernet link established. It will flicker with RX/TX activity. OFF – No ethernet link.

FAQ

• Q: How do I enroll Envisalink 3 with DSC systems?
  • A: Envisalink 3 automatically enrolls with DSC systems as PC5400/DVACS module.
• Q: What should I do for Honeywell systems before connecting Envisalink?
  • A: Create the user’s Connect2Go account and activate the module on the account before connecting it to the panel.

Documents / Resources

connect2go Envisalink 4 C2GIP Internet Module [pdf] Installation Guide Envisalink 4 C2GIP Internet Module, Envisalink 4 C2GIP, Internet Module, Module

References

• User Manual