Conic > RIB1940Z
ZOOM and Rotation
19pcs 40W 4-in-1
User Manual
KEEP THIS MANUAL FOR FUTURE NEEDS
1. Unpacking
Thank you for choosing our fixture. For your own safety, please read this manual before installing the device. This manual covers the important information on installation and applications. Please install and operate the fixture with following instructions. Meanwhile, please keep this manual well for future needs.
This fixture is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theater, studio, nightclubs and discos.
4-IN-1 LEDs(RGBW) which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation. And please check whether the following items are included inside the box:
Moving Head———One Signal Cable—-One
Hanging Bracket—–Two Power Cable—-One
Safety Cable———one User Manual—-One
2. Product dimension
3. Safety Instructions
CAUTION!
Be careful with your operations.With a dangerous voltage you can Suffer a dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
4. Operation Instructions
-The fixture is for beam wash and effect use.
-Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
-This light should be keep away from strong shaking during any transportation or movement.
-Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
-Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the fixture.
-Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.
-Make sure the lens are in good condition. It’s recommended to replace the units if there are any damages or severe scratch.
-Make sure the fixture is operated by qualified personnel who knows the fixture before using.
-Keep the original packages if any second shipment is needed.
-Don’t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies.
-It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
5. Mounting and Installation
Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture from a periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.
Clamp Mounting: The product provides a unique mounting bracket assembly that integrates the bottom of the base, the included “Omega Bracket,” and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the “omega bracket”. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly
(1) Omega Bracket
(2) Safety Clamp
(3) Safety Cable
(4) 1/4 Turn Quick-Lock Fastoners
a) Turn around
Regardless of the rigging option you choose for our fixture, always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.
6. DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving heads be connected together through serial linking. The cable needed should be two core, screened cable with XLR input and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator
- DMX IN
- POWER IN
DMX Output DMX Input
3-pin XLR Socket 3-pin XLR Socket
1: Ground
2: Data (-)
3: Data (+)
1=GND
2=DMX”-”
3=DMX”+”
a) DMX IN
b) DMX OUT
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.
| 7 2
|
. DMX Channels 2 channels mode |
||||
| CH | Function | DMX | Details | ||
| 1 | Pan | Pan movement control | |||
| 2 | Pan fine | 0-255 | Pan fine control | ||
| 3 | Tilt | 0-255 | Tilt movement control | ||
| 4 | Tilt fine | 0-255 | Pan fine control | ||
| 5 | Pan/Tilt speed | 0-255 | Speed from fast to slow | ||
| 6 | ZOOM | 0-255 | Zoom | ||
| 7 | LENS rotation | 0-127 | 0 to 60 degree | ||
| 128-191 | Unlimited clockwise rotation from fast to slow | ||||
| 192-255 | Unlimited anticlockwise rotation from fast to slow | ||||
| 8 | Dimmer | 0-255 | 0-100 linear dimmer from dark to bright | ||
| 9 | Strobe | 0-3 | No function, Light off | ||
| 4-200 | Strobe with the same step from slow to fast | ||||
| 201-255 | Random strobe from slow to fast | ||||
| 10 | R | 0-255 | 1-100% Red linear dimmer from dark to bright | ||
| 11 | G | 0-255 | 1-100% Green linear dimmer from dark to bright | ||
| 12 | B | 0-255 | 1-100% Blue linear dimmer from dark to bright | ||
| 13 | W | 0-255 | 1-100% White linear dimmer from dark to bright | ||
| 14 | Color temperature | 0-255 | Linear color temperature control | ||
| 15 | Marco | 0-255 | Marco color change | ||
| 16 | Static effect | 0-9 | No function | ||
| 10-84 | Each 5 DMX value is a kind of static effect(15 kinds) | ||||
| 85-255 | 16th kind of effect | ||||
| 17 | Dynamic effect | 0-9 | No function | ||
| 10-199 | Each 5 DMX value is a kind of dynamic effect(38 kinds) | ||||
| 200-255 | 39th kind of effect | ||||
| 18 | Dynamic effect speed | 0-127 | Anti-clockwise rotate from fast to slow, operate against 17 CH | ||
| 128-255 | Clockwise rotate from slow to fast, operate against 17 CH | ||||
| 19 | LED ring strobe | 0-3 | No function, Light off | ||
| 4-250 | LED ring strobe | ||||
| 251-255 | No function, Light on | ||||
| 20 | LED ring macro | 0-51 | Macro color | ||
| 52-255 | Dynamic effect, every 4 DMX channel is one kind of effect, totally 51 kinds | ||||
| 21 | Macro speed | 0-255 | LED ring macro effect from slow to fast | ||
| 22 | Reset | 0-239 | No function | ||
| 240-255 | Reset with 5 seconds | ||||
| 2 6
|
channels mode |
||||
| CH | Function | DMX | Details | ||
| 1 | Pan | Pan movement control | |||
| 2 | Pan fine | 0-255 | Pan fine control | ||
| 3 | Tilt | 0-255 | Tilt movement control | ||
| 4 | Tilt fine | 0-255 | Pan fine control | ||
| 5 | Pan/Tilt speed | 0-255 | Speed from fast to slow | ||
| 6 | ZOOM | 0-255 | Zoom | ||
| 7 | LENS rotation | 0-127 | 0 to 60 degree | ||
| 128-191 | Unlimited clockwise rotation from fast to slow | ||||
| 192-255 | Unlimited anticlockwise rotation from fast to slow | ||||
| 8 | Dimmer | 0-255 | 0-100 linear dimmer from dark to bright | ||
| 9 | Strobe | 0-3 | No function, Light off | ||
| 4-200 | Strobe with the same step from slow to fast | ||||
| 201-255 | Random strobe from slow to fast | ||||
| 10 | R | 0-255 | 1-100% Red linear dimmer from dark to bright | ||
| 11 | G | 0-255 | 1-100% Green linear dimmer from dark to bright | ||
| 12 | B | 0-255 | 1-100% Blue linear dimmer from dark to bright | ||
| 13 | W | 0-255 | 1-100% White linear dimmer from dark to bright | ||
| 14 | Color temperature | 0-255 | Linear color temperature control | ||
| 15 | Marco Color | 0-255 | Marco color change | ||
| 16 | Static effect | 0-9 | No function | ||
| 10-84 | Each 5 DMX value is a kind of static effect(15 kinds) | ||||
| 85-255 | 16th kind of effect | ||||
| 17 | Dynamic effect | 0-9 | No function | ||
| 10-199 | Each 5 DMX value is a kind of dynamic effect(38 kinds) | ||||
| 200-255 | 39th kind of effect | ||||
| 18 | Dynamic effect speed | 0-127 | Anti-clockwise rotate from fast to slow, operate against 17 CH | ||
| 128-255 | Clockwise rotate from slow to fast, operate against 17 CH | ||||
| 19 | Background R | 0-255 | Background color Red dimmer | ||
| 20 | Background G | 0-255 | Background color Green dimmer | ||
| 21 | Background B | 0-255 | Background color Blue dimmer | ||
| 22 | Background W | 0-255 | Background color White dimmer | ||
| 23 | LED ring strobe | 0-3 | No function, Light off | ||
| 4-250 | LED ring strobe | ||||
| 251-255 | No function, Light on | ||||
| 24 | LED ring macro | 0-51 | Macro color | ||
| 52-255 | Dynamic effect, every 4 DMX channel is one kind of effect, totally 51 kinds | ||||
| 25 | Macro speed | 0-255 | LED ring macro effect from slow to fast | ||
| 26 | Reset | 0-239 | No function | ||
| 240-255 | Reset with 5 seconds | ||||
| 36
|
Channels mode |
||||
| CH | Function | DMX | Details | ||
| 1 | Red | 0-255 | Red dimmer | ||
| 2 | Red Fine | 0-255 | Red fine control | ||
| 3 | Green | 0-255 | Green dimmer | ||
| 4 | Green Fine | 0-255 | Green fine control | ||
| 5 | Blue | 0-255 | Blue dimmer | ||
| 6 | Blue Fine | 0-255 | Blue fine control | ||
| 7 | White | 0-255 | White dimmer | ||
| 8 | White Fine | 0-255 | White fine control | ||
| 9 | CTO | 0-255 | Color temperature linear control | ||
| 10 | Macro color | 0-255 | Marco color effect | ||
| 11 | strobe | 0-3 | No function, Light off | ||
| 4-103 | Strobe with the same step from slow to fast | ||||
| 104-107 | No function, light up | ||||
| 108-207 | Pulse strobe from slow to fast | ||||
| 208-212 | No function, light up | ||||
| 213-251 | Random strobe from slow to fast | ||||
| 252-255 | No function, light up | ||||
| 12 | Dimmer | 0-255 | 0-100 linear dimmer from dark to bright | ||
| 13 | Dimmer Fine | 0-255 | Dimmer fine control | ||
| 14 | Pan | 0-255 | Pan movement control | ||
| 15 | Pan Fine | 0-255 | Pan fine control | ||
| 16 | Tilt | 0-255 | Tilt movement control | ||
| 17 | Tilt Fine | 0-255 | Pan fine control | ||
| 18 | Function | 0-255 | |||
| 19 | Reset | 0-250 | No function | ||
| 251-255 | Reset with 5 seconds | ||||
| 20 | Zoom | 0-255 | ZOOM | ||
| 21 | LENS Rotation | 0-127 | 0 to 60 degree | ||
| 128-191 | Unlimited clockwise rotation from fast to slow | ||||
| 192-255 | Unlimited anticlockwise rotation from fast to slow | ||||
| 22 | Shape Selection | 0-255 | Selecting shape(0-70 workable) | ||
| 23 | Shape Speed | 0-255 | Shape speed control | ||
| 24 | Shape Fade | 0-255 | Shape fade | ||
| 25 | Shape R | 0-255 | Shape in Red color | ||
| 26 | Shape G | 0-255 | Shape in Green color | ||
| 27 | Shape B | 0-255 | Shape in Blue color | ||
| 28 | Shape W | 0-255 | Shape in White color | ||
| 29 | Shape Dimmer | 0-255 | Shape dimmer 0-100% | ||
| 30 | Background Dimmer | 0-255 | Background dimmer 0-100% | ||
| 31 | Shape Transition | 0-255 | Shape change | ||
| 32 | Shape Offset | 0-255 | Shape offset | ||
| 33 | Foreground strobe | 0-255 | Foreground strobe control | ||
| 34 | Background strobe | 0-255 | Background strobe control | ||
| 35 | Background selection | 0-255 | Background selection | ||
| 36 | Frequency | 0-255 | Shape and frequency selectable | ||
| 78
|
Channels mode |
||||
| CH | Function | DMX | Details | ||
| 1 | Red | 0-255 | Red dimmer | ||
| 2 | Red Fine | 0-255 | Red fine control | ||
| 3 | Green | 0-255 | Green dimmer | ||
| 4 | Green Fine | 0-255 | Green fine control | ||
| 5 | Blue | 0-255 | Blue dimmer | ||
| 6 | Blue Fine | 0-255 | Blue fine control | ||
| 7 | White | 0-255 | White dimmer | ||
| 8 | White Fine | 0-255 | White fine control | ||
| 9 | CTO | 0-255 | Color temperature linear control | ||
| 10 | Macro Color | 0-255 | Marco color | ||
| 11 | strobe | 0-3 | No function, Light off | ||
| 4-103 | Strobe with the same step from slow to fast | ||||
| 104-107 | No function, light up | ||||
| 108-207 | Pulse strobe from slow to fast | ||||
| 208-212 | No function, light up | ||||
| 213-251 | Random strobe from slow to fast | ||||
| 252-255 | No function, light up | ||||
| 12 | Dimmer | 0-255 | 0-100 linear dimmer from dark to bright | ||
| 13 | Dimmer Fine | 0-255 | Dimmer fine control | ||
| 14 | Pan | 0-255 | Pan movement control | ||
| 15 | Pan Fine | 0-255 | Pan fine control | ||
| 16 | Tilt | 0-255 | Tilt movement control | ||
| 17 | Tilt Fine | 0-255 | Pan fine control | ||
| 18 | Function | 0-255 | Revered channel, no function at this moment | ||
| 19 | Reset | 0-250 | No function | ||
| 251-255 | Reset with 5 seconds | ||||
| 20 | Zoom | 0-255 | Zoom | ||
| 21 | Zoom Rotation | 0-127 | 0 to 60 degree | ||
| 128-191 | Unlimited clockwise rotation from fast to slow | ||||
| 192-255 | Unlimited anticlockwise rotation from fast to slow | ||||
| 22 | Red dimmer 1 | 0-255 | LED 1 red dimmer | ||
| 23 | Green dimmer 1 | 0-255 | LED 1 green dimmer | ||
| 24 | Blue dimmer 1 | 0-255 | LED 1 blue dimmer | ||
| 25 | Red dimmer 2 | 0-255 | LED 2 red dimmer | ||
| 26 | Green dimmer 2 | 0-255 | LED 2 green dimmer | ||
| 27 | Blue dimmer 2 | 0-255 | LED 2 blue dimmer | ||
| …… | ……… | ……… | ……… | ||
| … | ……… | ……… | ……… | ||
| 76 | Red dimmer 19 | 0-255 | LED 19 red dimmer | ||
| 77 | Green dimmer 19 | 0-255 | LED 19 green dimmer | ||
| 78 | Blue dimmer 19 | 0-255 | LED 19 blue dimmer | ||
8. Display instruction
9. Key Features
Voltage: AC100V～240V 50-60HZ
Power: 320W
LED Source: 19x40W high power RGBW 4 in 1 LEDs
Zoom: 6-60°
Strobe: 0-25Hz
Control Mode: DMX512,Sound-actived,Master/slave
DMX Channels: 22/26/36/78 four channel mode
Dimmer: 0-100% linear dimmer
Pan: 540°+16 bit fine
Tilt: 220°+16 bit fine
Display: LCD colorful display
IP: IP20
Fixture dimension: 405*234*440mm
N.W:15.2 Kg
G.W: 18.7 Kg
Package dimension: 62*39*51 CM (1pc/ctn)
Special Points.
- Each LED can be controlled individually. With unique honeycomb designed lens
- The front lens can rotate without limitation in forward and reverse direction to create amazing effects
- Can be used as beam, wash or effect light use (Kaleido effects)
- With a extra LED ring for eye-candy effect, LED ring with macro effect
10. Maintenance and Cleaning
Documents / Resources
 |
CONIC DESIGN RIB1940Z Zoom and Rotation 19pcs 40W 4 In 1 Moving Head Light [pdf] User Manual RIB1940Z, Zoom and Rotation 19pcs 40W 4 In 1 Moving Head Light, RIB1940Z Zoom and Rotation 19pcs 40W 4 In 1 Moving Head Light, 19pcs 40W 4 In 1 Moving Head Light, 40W 4 In 1 Moving Head Light, Moving Head Light |
