Concept R CP-RB-090 Heater Railing Bracket Set
About this instruction manual
Read these instructions for installation carefully and keep them within reach of the product. This ensures that you can refer to information regarding your safety and regarding installation at any time.
Symbols
In these installation instructions, symbols and signal words are used which have the following meanings:
ATTENTION!
This keyword is a warning that damage to property can occur.
This symbol indicates tips and useful information.
Important information for your safety
Intended use
The bracket set CP-R-HSR enables the attachment of a wooden railing to all Concept R sauna heaters.
Any use exceeding this scope is considered improper use. Improper use can result in damage to the product and injuries.
The bracket set CP-R-HSR is suitable for the following railing models:
| Article number | Description | Matching heater models |
| CP-R-L1 | Small linden wood railing | CP-RB-090 / CP-RB-105 |
| CP-R-L2 | Large linden wood railing | CP-RB-120 / CP-RB-150 CP-RCB-090 / CP-RCB-105 |
| CP-R-N1 | Small walnut wood railing | CP-RB-090 / CP-RB-105 |
| CP-R-N2 | Large walnut wood railing | CP-RB-120 / CP-RB-150 CP-RCB-090 / CP-RCB-105 |
General safety information
- Remove any packaging residue from the bracket. This could ignite during operation of the sauna heater.
- Mount the railing bracket and the finished railing with a normal screwdriver. The product can be damaged by a cordless drill.
- For your own safety, consult your supplier in the event of problems that are not described in sufficient detail in the operating instructions.
Scope of delivery
- 2 pcs railing bracket
- 4 pcs rounded head screws (A2 M 3 x 6 mm)
- 28 pcs wood screws (13 mm)
- 2 pcs mounting bracket
Optional accessories
Large wood railing (CP-R-L2 and CP-R-N2)
Small wood railing (CP-R-L1 and CP-R-N1) 
Installation
ATTENTION!
Damage to the product
The product can be damaged by a cordless drill.
Use a normal screwdriver to install the railing bracket.
Installing the railing bracket
- Step 1
Remove screws A and B from the sauna heater using a screwdriver. - Step 2
Screw the railing bracket 1 to the sauna heater. To do this, use screws A and B.
Install the second railing bracket in the same way on the opposite side of the heater.
Installing wooden parts on the mounting bracket
To do this, use the wood screws provided. - Step 3
Screw the side panels 3 to the mounting bracket 2. For each side panel, use 4 wood screws. - Step 4
Screw the short wooden panels 4 to the mounting bracket 2. For each wooden panel, use 2 wood screws.
- Step 5
Connect the two mounting brackets 2 with the medium or long wooden panels (5 or 6). For each wooden panel, use 4 wood screws.
Installing the railing
ATTENTION!
Damage to the product
The product can be damaged by a cordless drill.
Use a screwdriver to install the railing. - Step 6
Screw the railing from above to the railing brackets. To do this, use the rounded head screws provided.
Disposal
Please dispose of packaging materials in accordance with the applicable disposal regulations.- Used products contain reusable materials and hazardous substances. Therefore, do not dispose of your used product with household waste, but do so in accordance with the locally applicable regulations.
+43 (0) 7672/22900-50 | info@harvia.com www.harvia.com
FAQ
- Q: What railing models are compatible with the CP-R-HSR bracket set?
- A: The CP-R-HSR bracket set is suitable for small and large linden wood railings (CP-RB-090/105, CP-RB-120/150) and small and large walnut wood railings (CP-RCB-090/105, CP-RB-120/150).
- Q: Can I use a cordless drill to install the railing bracket?
- A: No, it is recommended to use a normal screwdriver to prevent damage to the product.
Documents / Resources
 | Concept R CP-RB-090 Heater Railing Bracket Set [pdf] Instruction Manual CP-RB-090, CP-RB-105, CP-RB-120, CP-RB-150, CP-RCB-090, CP-RCB-105, CP-RB-090 Heater Railing Bracket Set, CP-RB-090, Heater Railing Bracket Set, Railing Bracket Set, Bracket Set, Set |
