WLW7000E2 WiFi 7 Single Band Module
“
Specifications:
- Power Requirements: DC Power 5V
- Power Consumption: 12.3W (Max)
Product Usage Instructions:
Component Map:
The hardware consists of CH0, CH1, CH2, and CH3 components,
along with Ground Pin and 5V External Power Pin.
M.2 E Key Edge Connector:
The M.2 E Key Edge Connector has specific pin assignments on the
top and bottom sides, each serving different functions.
Power Pin Assignments:
Ensure proper connection of VDD_5V pins and avoid connecting
pins 15, 17, 19, 21, and 23 with your board when using the 5V
External Power Pin.
Voltage Options:
Pins 52, 53, and 55 support either 1.8V or 3.3V. It’s crucial to
select only one voltage option for these pins. The default voltage
for these pins is 1.8V.
Mechanical Key E:
Pin assignments for the M.2 Edge Connector vary on the top and
bottom sides, with each pin serving a specific function. Ensure
correct connections for proper functionality.
FAQ:
Q: Can I use a different voltage option for pins 52, 53, and
55?
A: Pins 52, 53, and 55 support either 1.8V or 3.3V. However,
it’s important to note that you can only select one voltage option
for these pins to avoid any damage to the hardware.
Q: What is the default voltage for pins 52, 53, and 55?
A: The default voltage for pins 52, 53, and 55 is set to 1.8V.
Ensure to adhere to this default setting unless specifically
required to change it based on your setup’s specifications.
“`
Hardware Guideh-aWrdLwWa7re00gu0iEd2e
Component Map
CH0 CH1 CH2 CH3
Ground Pin
5V External Power Pin
M.2 E Key Edge Connector
Power Requirements
DC Power
5V
Power Consumption 12.3W (Max)
*For the customer who want to use 5V External Power Pin, please make sure pins 15, 17, 19, 21 and 23 were not connected with your board.
*For pins 52, 53 and 55 support either 1.8V or 3.3V. However, it’s important to note that you can only select one voltage option for these pins.
*Default voltage for pins 52, 53 and 55 is 1.8V.
M.2 Edge Connector Pin Assignment
M.2 edge connector pin assignment
Top side
Bottom side
1
GND
2
VDD_3V3
3
REFCLK_IO_P0
4
VDD_3V3
5
REFCLK_IO_N0
6
PCIE_LED0(GPIO25)
7
GND
8
NC
9
PTA2_BT_ACT
10
NC
11
PTA2_BT_PRIO
12
NC
13
PTA2_WL_ACT
14
WSI_DAT_OUT(GPIO48)
15
VDD_5V
16
NC
17
VDD_5V
18
GND
19
VDD_5V
20
WSI_CLK_OUT(GPIO49)
21
VDD_5V
22
NC
23
VDD_5V
Mechanical key E
33
GND
32
WSI_DAT_IN(GPIO50)
35
PCIE0_RX0_P
34
GND
37
PCIE0_RX0_N
36
WSI_CLK_IN(GPIO51)
39
GND
38
NC
41
PCIE0_TX0_P
40
NC
43
PCIE0_TX0_N
42
NC
45
GND
44
PTA1_BT_PRIO
47
PCIE0_REFCLK_P
46
PTA1_WL_ACT
49
PCIE0_REFCLK_N
48
PTA1_BT_ACT
51
GND
50
NC
53
PCIE0_CLKREQ_N
52
PCIE0_RST_N
55
PCIE0_WAKE_N
54
NC
57
GND
56
WLAN_DISABLE
59
NC
58
NC
61
NC
60
NC
63
GND
62
NC
65
NC
64
NC
67
NC
66
NC
69
GND
68
NC
71
REFCLK_IO_N1
70
NC
73
REFCLK_IO_P1
72
VDD_3V3
75
GND
74
VDD_3V3
Copyright © Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of Compex Systems Pte. Ltd. While every effort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise.
hardware guide All specifications are subject to change without notice.
Compex Systems Pte Ltd | www.compex.com.sg | (+65) 6288 8220 | sales@compex.com.sg | Last Updated: 21/11/2024 MW, YX, GS, HJ
Documents / Resources
 |
COMPEX WLW7000E2 WiFi 7 Single Band Module [pdf] Instructions QCN6224, QCN6274, QCN9274, WLW7000E2 WiFi 7 Single Band Module, WLW7000E2, WiFi 7 Single Band Module, Single Band Module, Band Module |