COMNOVA WB-TS298SD Style Nerf Bars Running Boards
Specifications
- Product: S6 Running Boards
- Compatibility: 2022-2024 Toyota Tundra Crewmax
- Part Numbers: WB-TS298SD (Driver/Left), WB-TS298BD (Passenger/Right)
- Cleaning Instructions: Use mild soap only, avoid abrasive polishes or waxes
Product Usage Instructions
Installation Steps for Passenger/Right Side:
Front Mounting Location:
- Remove plastic plugs or hex bolts from threaded holes.
- Attach the Passenger/Right Front Mounting Bracket using provided hardware.
Center (2nd) Location:
- Attach one Passenger/Right Rear Mounting Bracket to the 2nd location.
Rear Location:
- Attach the remaining Passenger/Right Rear Mounting Brackets to the 3rd and rear locations.
- Secure the Passenger/Right Running Board to all four mounting brackets.
FAQ
Frequently Asked Questions
- Q: Can the running boards be installed on other vehicle models?
- A: These running boards are specifically designed for the 2022-2024 Toyota Tundra Crewmax and may not be compatible with other models.
- Q: What should I do if I encounter missing parts during installation?
- A: Contact customer support immediately to request replacement parts for a complete installation.
PARTS LIST
| 1 | Driver/Left S6 Running Board | 8 | 8mm x 35mm Double Bolt Plates |
| 1 | Passenger/Right S6 Running Board | 16 | 8mm x 30mm Hex Bolts |
| 1 | Driver/Left Front Mounting Bracket | 16 | 8mm Lock Washers |
| 1 | Passenger/Right Front Mounting Bracket | 32 | 8mm x 24mm OD x 2mm Flat Washers |
| 3 | Driver/Left Rear Mounting Brackets | 16 | 8mm Nylon Lock Nuts |
| 3 | Passenger/Right Rear Mounting Brackets |
Installation Instructions
PROCEDURE:
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS HIGHLY RECOMMENDED.
- Starting on the Passenger/Right side of the vehicle and remove the plastic plugs or hex bolts from the factory mounting location along the bottom of the body, (Figures 1 & 4).
- Select the Passenger/Right Front Mounting Bracket. Attach the Bracket to the front location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 2 & 3). Do not tighten hardware.
- Repeat Steps 2 & 3 to attach the (3) Rear Mounting Brackets, (Figures 4—8).
- Unwrap the Passenger/Right S6 Running Board. Select (4) 8mm Double Bolt Plates, (Figure 9). Insert the Bolt Plates into the channel in the bottom of the Running Board.
- Place the Running Board on top of the (4) Mounting Brackets. Lift the Running Board up and guide the studs down through the Brackets.
- IMPORTANT: Do not slide the Running Board on the Brackets, (front to back or rotate), or the finish on the Running Board may be damaged.
- Attach the Running Board to the Brackets with (8) 8mm Flat Washers and (8) 8mm Nylon Lock Nuts, (Figure 9). Do not tighten hardware.
- Level and adjust the Running Board and tighten all hardware.
- Repeat Steps 1—8 to attach the Driver/Left S6 Running Board.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment: Do not use any type of polish or wax that may contain abrasives that could damage the finish. Use only mild soap to clean the Running Boards.
Documents / Resources
 |
COMNOVA WB-TS298SD Style Nerf Bars Running Boards [pdf] Instruction Manual WB-TS298SD, WB-TS298BD, WB-TS298SD Style Nerf Bars Running Boards, WB-TS298SD, Style Nerf Bars Running Boards, Nerf Bars Running Boards, Running Boards, Boards |