CommScope C1004 10G Epon Bridging Onu User Manual
CommScope’s C1004 Bridging ONU (Optical Network Unit) provides user interfaces to an EPON or 10G EPON optical network. User interfaces include 4ea GE ports, each capable of independent full 1GE throughput, in a package suitable
for wall, desk, or flat surface mounting.
FEATURES
- Supports all EPON rates:
- 10Gbps / 10Gbps
- 10Gbps / 1Gbps
- 2Gbps / 1Gbps (Turbo mode)
- 1Gbps / 1Gbps
- CableLabs DPoE 1.0 and 2.0 compliant
- Service policy enforcement per LLID with 16 bidirectional LLIDs
- 32 upstream queues / 64 downstream queues (16 queues per UNI port)
- IEEE 802.1p with up to eight priority queues per LLID
- IEEE 802.1D bridging
- IEEE 802.1Q VLAN mapping to LLIDs
- L2/L3/L4 line-rate packet processing supporting classification, modification, filtering, and custom rule-table processing
- 44 programmables ins per ling or bill port with 16 priority levels
- VLAN tag translation, Q-in-Q, tag addition/deletion, and modifications for 4K VANS
- Unicast, broadcast, and multicast traffic support
- IGMP v2/MLD v1 and IGMP v3/MLD v2 snooping
- IPv4 and IPv6 support
- Selectable encryption mode per LLID:
- IEEE 802. 1ae (128-bit AES) bidirectional
- IEEE OAM, DPOE 1.0 OAM, and Operator OAM
- Selectable encryption mode per LLID:
- IEEE 802.1ae (128-bit AES) bidirectional
- IEEE 802.1X authentication
- IEEE 802.3ah frame-based FEC and IEEE 802.3av stream-based 10G FEC
- 4K MAC address learning table for 802.1D bridging
HARDWARE
| ITEM | DESCRIPTION | |
| Mounting | Wall, desktop, under desk, flat surface mounting | |
| Physical Dimensions | Dimensions | 288.50(W) x 186.60(D) x 52.50(H) mm |
| Weight | 700g | |
|
Interface |
PON | IEEE 802.3av |
| LAN | 10/100/1000BaseTx (RJ-45: 4 ports), MDI/MDIX Auto-Negotiation | |
| Power Switch | On/Off | |
| Power | DC 12V | |
| Reset Switch | Reset to factory defaults | |
|
Front Panel LED |
Power | Power On/Off status |
| PON | Logical Link status of PON, Loss Of Signal | |
| DATA | PON Link and Data Transmission status | |
| LAN 1/2/3/4 | LAN Link and Data Transmission status | |
PHYSICAL INTERFACES
| NAME | CONNECTION | DESCRIPTION | ||
| ON/OFF switch | Power On / Off | |||
| Power Jack | DC 12V | Input terminal for power adaptor connection | ||
| LAN 1/2/3/4 | RJ-45 | Connected through a LAN port UTP cable | ||
| Line | SC/UPC | EPON port | ||
OPTICAL SPECIFICATIONS, RX
| PARAMETER | SPECIFICATION | COMMENTS | ||
| PON Input Power, maximum | -3.0 dBm | |||
| PON Input Power, maximum | -26.5 dBm | |||
| PON Wavelength, nominal | 1577.00 nm (10G) or 1490.00 nm (1G) | |||
OPTICAL SPECIFICATIONS, TX
| PARAMETER | SPECIFICATION | COMMENTS | ||
| Bit Error Ratio, maximum | 10-10 | |||
| Laser Type | Distributed feedback (DFB) Class 1 | |||
| Output Power Range | 0–4 dBm | |||
| Wavelength, nominal | 1270.00 nm (10G) or 1310.00 nm (1G) | |||
ELECTRICAL SPECIFICATIONS
| PARAMETER | SPECIFICATION | COMMENTS | ||
|
Electromagnetic Compatibility/Interference |
ANSI C63.4 | AS/NZS 4771/Amdt 1 | C-Tick | CAN/CSA 22.2 no. 60065 | EN 300 328
V1.7.1 | EN 301 489-1 V1.9.2 | EN 55022 Class B | EN 60950-1 | IC RSS-210, Issue 8 | IRAM | UL 60065 | US FCC Part 15 Subpart C |
|||
| Power Consumption, maximum | 18.5 W | |||
| Voltage | 12.0 Vdc | |||
| Power Adapter | Input Voltage: 100-220VAC, 50/60Hz
Output: 12VDC, 3A |
|||
ENVIRONMENTAL SPECIFICATIONS
| PARAMETER | SPECIFICATION | COMMENTS | ||
| Operating Temperature |
0 °C to +50 °C (+32 °F to +122 °F) |
|||
| Relative Humidity | 20%–80%, non-condensing | |||
ENVIRONMENTAL SPECIFICATIONS
| PARAMETER | SPECIFICATION | COMMENTS | ||
| Ethernet Ports, UNI |
IEEE 802.3 (10/100/1000 Base-TX) |
|||
| Ethernet Ports, UNI, quantity | 4 | |||
| PON Interface | SC/UPC Female | |||
| PON Interface Standard (as
shipped) |
PX20, single-mode fiber | |||
| PON Interface, quantity | 1 | |||
| Power Supply | Required; 12VAC | External power adapter | ||
NETWORK PARAMETERS
- Wire-speed LAN
- Full-duplex mode LAN
- Auto MDI/MDIX (Medium Dependent Interface Cross) LAN
- IEEE 802.1q VLAN (tagged, untagged by port)
- 16 Active VLANs (max)
- VLAN ID range: 1 – 4094
- Up to 64 MAC addresses
- 32 Multicast Group entries
- Multicast throughput: 1Gbps
DHCP
- DHCP Client
- DHCP Server
- In NAT mode, the IP will be assigned from the IP the pool of the device; in Bridge mode, the IP will be assigned from the network DHCP server
- DNS/DNS Proxy
MULTICAST PARAMETERS
- IGMP v1/v2/v3
- IGMP Snooping
- IGMP Immediate Leave on/off
- IGMP Proxy
NAT/NAPT
- Selectable between NAT and bridge modes
- Dynamic/static private IP in NAT mode
- Port Forwarding and DMZ Host functions
- 8,000 bi-directional concurrent sessions (maximum, full-wire-speed)
QOS
| PARAMETER | SPECIFICATION | COMMENTS | ||
|
Classification |
Physical port 802.1p
SRC/DST IP address TOS/DSCP TCP/UDP SRC/DST port |
Layer 1, 2, 3, 4 |
||
| Marking | 802.1p DSCP | Layer 2, 3 | ||
| Scheduling | SPQ | 3 Queues per interface | ||
- Rate limiting (±10%)
- QoS for both upstream and downstream
MANAGEMENT
- TR-069 compliant
- System or module LED
- Local and remote Firmware Upgrade (The existing Image should be kept when the upgrade fails).
- A normal session for a system management event with CPU overload
- Remote Management
- Remote access through Telnet (RFC 854, 855)
- CPE Management Server
- Device Reset
- Setting and changing Config
- Firmware download via Web Server
- Time sync via NTP server
- Device status and performance management
SECURITY
- Broadcast storm control
- MAC filtering
- IP filtering
IPV6
- Dual-stack
- ICMPv6
- DHCP Server and IPv6 addressing (stateful/stateless address)
FUNCTIONAL SPECIFICATIONS
| PARAMETER | SPECIFICATION | COMMENTS | ||
| PON Standards | IEEE 802.3
IEEE 802.3av (10G) |
Layer 1, 2, 3, 4 | ||
| Technology Types | EPON
10G UPON |
Layer 2, 3 | ||
GENERAL SPECIFICATIONS
| PARAMETER | SPECIFICATION | COMMENTS | ||
| Installation | Desktop, Wall, Under Desk, Flat Surface | |||
| Location | Indoor | |||
| Warranty | One year | |||
LED INDICATORS
| LABEL | DESCRIPTION | STATUS | INDICATION | |||
|
PWR |
Power supply LED |
Green On | Power is fed. | |||
| Yellow On | When the fed power is either over (i.e. above 13.2V) Or under (i.e. below 9.6V) the voltage limit. | |||||
| OFF | No power is fed. | |||||
|
PON |
Authentication LED |
Green On | 10G Link On | |||
| Blue On | 1G Link On | |||||
| OFF | Link Off | |||||
|
LOS |
Loss of Signal |
Red On | PON Link is NOT established properly.
Or, the continuous optic signal is detected. |
|||
| OFF | PON Link is established properly. I.e. in normal status. | |||||
| DATA | Data port LED | Blue Blink | Packets are being transmitted between OLT and ONU. | |||
| OFF | No packets are being transmitted between OLT and ONU. | |||||
| LAN 1-4 | LAN port LED | Blue Blink | Packets are being transmitted | |||
OPTICAL FIBER CLAMP / SECURITY
2014 CommScope, Inc. All rights reserved. All trademarks indentified by or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information.
Download PDF: CommScope C1004 10G Epon Bridging Onu User Manual
