ACCESS Electrified Latch Retraction Kit
Instruction Manual
Electrified Latch Retraction Kit
MLRK1-KAWP
INSERT Instructions
The Command Access MLRK1-KAWP is a field-installable motorized latch-retraction kit for the Kawneer Paneling series exit devices.
Kit Includes
A. 60417 – MLRK1 motor
B. 50944 – Molex pigtail
C. 50030 – 6’ power cable
D. 60708/51186 – MM4T REMOTE MODULE
E. 51198 – Remote Module Cable
F. 40059 – (x2) CABLE MOUNTING PAD
G. 40060 – (x2) CABLE TIES
H. 40306 – Philips SCREWS (x4)
INSTALLATION VIDEO
https://l.ead.me/bc4djT
SPECIFICATIONS
- Input Voltage: 24-25.3VDC
- AVERAGE low Torque LATCH RETRACTION CURRENT: 900 mA
- Average high torque latch retraction current: 2A
- Average holding current: 215 ma
- Wire gauge: Minimum 18 gauge
- Direct wire run – no relays or access control units in-between power supply & module
Optional built-in rex
- SPDT – Rated .5a @24V
- green= Common (C)
- Blue = normally open (NO)
- grey = normally closed (NC)
REQUIRED COMMAND Power Supplies: Use a PS210/220/440B
All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. If you plan on using a non-Command power supply it must be a filtered & regulated linear power supply.
REMOVING AND DISASSEMBLING PUSH PAD INSTRUCTIONS
- Using a flat screw driver or putty knife, gently pry at top and bottom on Filler Plater on each side of device until they come out
- Once exposed remove (4) Philips head mounting screws and remove push pad from pocket in door
- Remove (4) Philips head screws attaching Push Pad to chassis
Remove Push Pad from chassis by pulling in opposite directions, if it proves difficult to separate, a rubber mallet can be used to get it past any stubborn points. Watch for bearings that may fall out during removal. 
Installation Instructions
- With the Push Pad removed, flip it over and locate the Rear Activating Bracket.
- Locate the Opening in the Rear Activating Bracket, this is where the kits head link will slide through.
- Flip the Motor Kit over so the underside is facing you, next slide the Head Link of the motor kit through the Rear Activating Bracket Opening.
- Fit the Hole on the end of the Head Link over the Rear Post of the Rear Mounting Bracket as shown.
- Then fit the Hole on the Motor Bracket over the Side Post of the Rear Mounting Bracket as shown.
- Once kit is in place connect 3-Pin and 4 -Pin Connectors on the Remote Module Cable to 3-pin and 4-Pin Connectors from Motor and Sensor. Apply Strain Relief as shown below or to installers best judgement.
- Guide wire to rear of device and feed through Back Activating Bracket. Ensure nothing is being pinched or strained by depressing the Back Activating Bracket.
- Before re-installing the Push Pad, ensure the bearings are still on the Activating Brackets!
- Re-install the Base Rail, making sure the Front Activating Bracket and Bearings slide into their Slots.
- The Two Tabs on the Motor Bracket, Rear Activating Bracket and Bearings must also slide into the Slots on the Base Rail.
- Re-secure the Biserial & re-mount the items that were removed in Step 4.
- Re-install Device back into the door.
- Connect 3-Pin and 4-Pin Connectors from RM Cable to Remote MM4 Module, mount Module in empty pocket using double sided tape. Hook incoming power to 2-Pin Connector using provided power lead.
- If mechanical adjustment of Retraction Arm is needed please follow instructions below
LIFT LEVER ADJUSTMENT
- Lubricate lever as indicated.
- Loosen the binder fastener on axle bracket.
- Rotate the axle bracket until the lever arm contacts the bottom of the traveler roller. Tighten the binder fastener to allow for operation testing.
- Stand the door up with a spacer between the door and the floor to allow for bolt operation and check for proper operation.
- After testing unit thoroughly, drill a hole at location “A” using a #23 (0.154 dia.) drill bit.
- Lock adjustment in place using extra binder fastener 028747.
PUSH TO SET (PTS)
Setting PUSH TO SET (PTS)
**Important Info** 
Make sure to set PTS before finishing installation
Step 1 – Select your preferred torque mode (ships in standard torque). Press the device push pad to the desired setting. (We recommend to fully depress and release 5%, giving the device room for changing door conditions.)
Step 2 – While depressing the push pad, apply power.
Step 3 – Continue to keep the pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and the adjustment is now set. Test the adjustment 4 to 5 times and if not to your liking repeat the above steps.
*Once you found your preferred adjustment, we recommend turning off the PTS programming switch.
Troubleshooting & Diagnostics
| Beeps | Explanation | Solution |
| 2 Beeps | Over Voltage | > 30V unit will shut down. Check voltage & adjust to 24 V. |
| 3 Beeps | Under Voltage | < 20V unit will shut down. Check voltage & adjust to 24 V. |
| 4 Beeps | Failed Sensor | Verify all 3 sensor wires are installed correctly. Replace sensor if problem persists by contacting office. |
| 5 Beeps | Retraction or dogging failure | After 1st fail: 5 beeps then immediately attempts to retract again. After 2nd fail: 5 beeps with pause in-between for 30 seconds then device attempts to retract again. After 3rd fail: 5 beeps every 7 minutes, device will not attempt to retract. To Reset: Depress bar for 5 seconds at any time. |
| 6 Beeps | PUSH TO SET | Device is recording it’s new position and power mode after the 6th beep. |
*TRIM POT ADJUSTMENT ONLY REQUIRED WHEN PTS PROGRAMMING IS NOT SETTING TO THE CORRECT LOCATION
*Latch bolt adjustment- If the latch bolt is not retracting far enough, turn the dial clockwise with a small flat blade screw driver. If the latch bolt is retracting too far causing the device to chatter and drop-out, turn the dial counter-clockwise until the chatter and drop-outs stop and the desired location is achieved.
US customer support
1-888-622-2377
www.commandaccess.com
Canada customer support 1-855-823-3002
Documents / Resources
 |
COMMAND ACCESS Electrified Latch Retraction Kit [pdf] Instruction Manual MLRK1-KAWP Electrified Latch Retraction Kit, MLRK1-KAWP, Electrified Latch Retraction Kit, Latch Retraction Kit, Retraction Kit, Kit |