ComfortStar CCWC-100-WIFI Wireless Wi-Fi Touch Screen Control
Installation method
This product allows embedded installation. Please refer to the following requirements to complete the installation of this product.
- Pull out the plug-in terminal from the product, connect wires respectively
- Insert and fasten 2 mounting screws (attached randomly) from the back of with 12V, G, and A1 and B1 terminals the panel into the 2 mounting and of RS485 as required by the wiring fixing bores on the left and right sides standard, and then insert a small of the product’s mounting base plate, flat-blade screwdriver into the until the product is securely fastened mounting base plate to take down to the panel. Recommended torque this plate. value: 6.0+/-0.5 kgfcm.
- Plug the connected terminals into the 4. Power on the controller after the product, and then push the product product is installed. into the mounting base plate inside the mounting box to suck it directly.
Wiring guidance
- Wiring shall be carried out by professionals under the state of no electricity.
- Wiring shall be carried out in strict accordance with the wiring diagram. Be sure not to reverse the power cord and the communication cord; do not reverse the power supply terminals 12V and GND; and the A and B ports of RS485 should correspond one-to-one, and should not be reversed.
- The interior of the product shall be protected from water, mud, and other sundries, and it is necessary to pay attention to the orientation of the equipment to avoid installing it in the wrong direction.
Function Description
Startup and loading
The product enters the boot screen after being powered on, and then loads the interface. The loading process is relatively slow due to the limit of the Android system. Please hold on. The System Configuration interface is entered after
loading.
System Configuration interface
After entering the System Configuration interface, first input the account and password. The default account and password for the service personnel are “admin” and “8699”.
Note: Please correctly select the language, which will determine the initial naming of the device.
Verify whether the number of the indoor and outdoor units is correct after
searching. Click Next/Finish to enter the Home page if the number is correct
Otherwise, click Search Again in the Outdoor Unit Information interface.
if in the Indoor Unit Information interface, click Return in the upper left
orner of the interface to return to the Outdoor Unit Information interface)
3 Indoor Unit Master Control interface
The main interface displays a list of all Indoor Units, which includes the
name, set temperature/fault condition, on/off status, mode, and fan speed of the
Indoor Unit, and the date and time of the centralized controller at its upper right
corner. You can click any of the Indoor Units to view its set states and control it.You can choose the cooling, heating, dehumidification, fan mode, or auto mode
after clicking the mode setting in the Master Control interface.
Note: For VRF system, auto mode is cooling actually.
The fan speed can not be changed under the dehumidification mode. The
setting temperature can not be changed under the fan mode.After clicking Auxiliary Function in the Master Control interface, you will enter
he Auxiliary Function interface, and can set the on/off status of Lighting,
horizontal winging, vertical Swinging, Economy Operation, Mode Lock, Remote
Lock, and Electric Auxiliary heater.
Note: Please refer to the actual model for the presence of such additional
functions.
The economy operation and electric auxiliary heater control are currently
serve functions on VRF system. Mode Lock only exists in VRF system,and can
lock merely the cooling and heating modes at present. It will judge to lock the
ooling mode if clicked under non-heating modes. Its icon will change according
to the locked mode after the locking.
4 Other functions
Click the half circle in the main interface to pop up a setting interface, and
then you can use other functions.1. Zone function:
The Zone function means a grouping function, and after grouping, you
can set the Indoor Units of a group with one click. You will go to the
main Zone Function interface after clicking Zone.
Documents / Resources
 |
ComfortStar CCWC-100-WIFI Wireless Wi-Fi Touch Screen Control [pdf] Instruction Manual CCWC-100-WIFI Wireless Wi-Fi Touch Screen Control, CCWC-100-WIFI, Wireless Wi-Fi Touch Screen Control, Wi-Fi Touch Screen Control, Touch Screen Control, Screen Control, Control |