Quick Installation Guide
Thank you so much for choosing Comfee’s appliances. We really appreciate your choice and would love to help you get started.
Unpacking
You’ll soon be enjoying your new appliance
This guide will help you get started, for full details, please refer to the instruction manual.
What’s in the box
Installation
Bringing it all together
Important: Before installing, please make sure there are rubber gaskets inside the fittings at both ends of the water supply hoses. Missing rubber gaskets can cause water leakage.
Install the Bottom Cover
Slide the bottom cover into the slots on the bottom surface of the unit as shown in the following figure. Fix it with two screws attached to the unit.
Connect the water hose
- Connect the ends of the water supply hoses to the HOT and COLD faucets. Use the Quick Connection Adaptor for connection to the COLD water faucet.
- Connect the ends of the water supply hoses to the water supply inlet connections at the back of the washer.
- Turn on the HOT and COLD water supplies and check all the water supply intake connections and the faucets for water leaks.
Connect the drain hose
The drain hose can be positioned in three different ways
Leveling your washer
See if the washer is level by checking the position of the tub or using a leveling gauge.
- Slide the washer into position.
- Open the lid of the washer, and pour water into the tub to just below the pulsator level.
- If the washer is level, the pulsator is positioned at the center of the washer as shown in the figure above right. If not, level your washer by turning the front leveling feet clockwise or counterclockwise as necessary.
Using your washing machine
Let’s get started
Running a test cycle
- Run a test cycle to check if your washer is properly installed.
The washer should not rock or vibrate excessively when water is supplied or when washing or spinning and should drain well during the spin cycle.
WARNING
If water leaks while water is being supplied or drained, check the water connections. If the washer rocks and vibrates excessively, level your washer again.
Troubleshooting
We are always here to help
If you require any technical guidance or find that your washing machine is not operating as intended, a simple solution can often be found in the Troubleshooting section of the Owner’s Manual.
Commonly seen error codes and solutions:
| Error Code | Description | Possible Cause | Solutions |
| El | Water is not supplied | 1. Water tap is not Check the water tap and open it fully | Check the water tap and open it fully |
| 2. Water inlet is blocked | Clean the valve filter with a brush | ||
| 3. Water inlet valve is broken | Replace the water inlet valve | ||
| E2 | Not draining | Drain-pipe is hung too high | Install the Drain-pipe as instructed |
| Drain valve is blocked | Unclog the drain valve | ||
| The drain pump filter is blocked | remove and unclog the drainage pump filter | ||
| E3 | Lid open alarm | The top lid is open | Close the lid and press the ON/OFF button |
| E4 | Unbalance alarm | The washing machine foot is not balanced | Check if the machine is level |
| Unbalanced load | Check if clothes are spread out evenly in the drum. Restart the machine when the load is redistributed. |
||
| XX | Others | Others | Restart the machine. call the service line if the problem still exists. |
For further assistance, feel free to contact us at 1-866-646-4332 with the following information ready:
| Model No. | CLV16N2AMG |
| Serial No. (You can find it on xxx) |
|
| Date of Purchase | |
| Problem |
Documents / Resources
 | Washing Machine |
References
- User Manualmanual.tools
I had no trouble setting it up! It seems very nice! Can you just give instructions like “if you only want spin cycle push this.” It’s so non intuitive and I’m tech literate!
How do I run a spin-only cycle on my Comfee washing machine?
To run a spin-only cycle on your Comfee washing machine, follow these steps using the control panel:
Please note that because specific button layouts can vary slightly by model, you should ensure the 'Spin' light is the only one active in the procedure sequence before starting.
Read the full Q&A page
洗濯が終わっても水がたらたらと垂れてきて気付いたら洗濯物がべちゃべちゃになります
対処法を教えてください
対処法を教えてください
How do I fix a Comfee washing machine that continues to drip water after the cycle ends, leaving clothes wet?
If water continues to drip into the drum after the cycle has finished, it usually indicates an issue with the water inlet valve or the drainage system. Based on the Comfee troubleshooting guide, please check the following:
If the dripping persists even when the machine is powered off, turn off the water supply faucets and contact Comfee customer service at 1-866-646-4332 for technical assistance.
Read the full Q&A page