2A88P-1005 Predictive Thermometer With WiFi Booster
“
Specifications
- Charging Type: USB-C
- Booster Charging Time: 60 minutes
- Thermometer Charging Time: 25 minutes
- Booster Battery Life/WiFi: 54 hours
- Thermometer Battery Life: 90+ hours
- Thermometer Battery Life (in Booster): Up to 9.5 months
Product Usage Instructions
Getting Started
- Charge your Combustion Booster for 60 minutes.
- Link your Booster to your Predictive Thermometer. Once linked,
the Booster will repeat the Thermometer’s Bluetooth signal.
Booster Modes
Portable Charger Mode: When unplugged, the
Booster’s onboard battery can recharge your Predictive Thermometer.
Press the button to check the thermometer’s charge level.
Wall Charger Mode: When plugged in, the Booster
will recharge itself and the Predictive Thermometer. The light will
be amber when either is charging and green when both are fully
charged.
Power Management
- If the Booster is not plugged in, it will search for linked
MeatNet-enabled Combustion tools to connect with. If no connection
is found, it will power down in 3 minutes. - To turn on the Booster, press the button. If connected,
indicated by a green blink, it will remain on. To turn it off, hold
the button for 1 second.
Firmware Update
Follow the instructions in the Combustion App to update the
Booster’s firmware, which is its internal operating system.
Setting up WiFi
Use the QR code or provided link for detailed instructions. In
summary:
- Download the app.
- Update all firmware.
- Charge all devices.
- In the app, navigate to ‘WiFi Devices’.
- Select your tool and ‘Join network’.
- Choose the network and enter the password.
FAQ
Q: What is the purpose of the Combustion Booster?
A: The Combustion Booster functions as a repeater for the
Predictive Thermometer’s Bluetooth signal and can also act as a
portable charger for the thermometer.
Q: How do I update the firmware of the Booster?
A: To update the Booster’s firmware, follow the instructions
provided in the Combustion App.
Q: How long does it take to charge the Booster and the
Predictive Thermometer?
A: The Booster charging time is 60 minutes, while the
Thermometer charging time is approximately 25 minutes.
“`
Getting started with your Combustion Booster
1
Charge your Booster 60 min.
· Use the included cable and any standard USB power supply (a phone charger works great)
· The light will be solid amber as the Booster charges
· When the Booster is charged, the light will turn green
2
Link your Booster to your Predictive Thermometer
· Unplug the Booster · The light will flash white 3 times in a
row to show it’s searching (this sequence repeats) · Hold a (fully charged) Predictive Thermometer near the Booster · A single white blink indicates the link has been established (it will blink every 5 seconds)
Congrats, your Booster is now repeating the Thermometer’s Bluetooth signal!
!
The Booster light–and what it’s trying to tell you:
Modes
Portable Charger Mode With the Booster unplugged, the onboard battery can recharge your Predictive Thermometer. Press the button (light) to check thermometer charge level.
NOTE: Booster will not act as a repeater while it’s recharging a thermometer.
Wall Charger Mode With the Booster plugged in, it will recharge itself and the Predictive Thermometer. If either is charging, the light will be amber. When both are charged, the light will turn green.
Power management
When the Booster is not plugged in, it will search for linked MeatNetenabled Combustion tools (Predictive Thermometer, Display) to connect with. If no connection is found, it will power itself down in 3 minutes.
To turn it back on, press the button (light). If connected (green blink), the Booster will remain on.
To turn it off, hold the button (light) for 1 second.
Firmware update
Follow the instructions in the Combustion App to update the Booster’s firmware (its internal operating system).
Light Solid Amber Amber Solid Green Green Blinking White x3 Single White Blink Quick Blue Blink Quick Red Blink
Power USB Battery USB Battery Battery Battery Any Battery
Status Charging Booster (and/or Thermometer) Charging Thermometer Everything is charged Thermometer is charged Searching for linked tools Connected + repeating Thermometer signal Booster is connected to WiFi Booster battery is low
combustion.inc/start
Setting up WiFi
Use the QR code or link for detailed instructions. Briefly: 1. Get the app 2. Update all the firmware 3. Charge everybody 4. In the app, ‘WiFi Devices’ 5. Select your tool, ‘Join network’ 6. Choose network + enter network
password
Designed by Combustion, Inc., in Seattle WA, USA. All rights reserved. The Combustion Inc. logo is owned by Combustion, LLC.
Thermometer Storage
2
1
charging status LED
Booster Functions
Button press
Repeater on
Button hold 1 sec
Repeater off
Button hold 10 sec
Factory reset
Max Temperatures
minimum insert
900 °F 482 °C
220 °F 105 °C
Charging
Charging type
Booster charging time
Thermometer charging time
Booster battery life/WiFi
Thermometer battery life
Thermometer battery life (in Booster)
USB-C 60 min 25 min 54 hours 90+ hours Up to 9.5 months
CAUTION The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (a) Reorient or relocate the receiving antenna, (b)Increase the separation between the equipment and receiver, (c) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, (d) Consult the dealer or an experienced radio/TV technician for help.
FCC & IC RADIATION EXPOSURE STATEMENT This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device contains licence-exempt transmitter/receiver that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
DÉCLARATION D’IC SUR L’EXPOSITION AUX RADIATIONS Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body
Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement porté sur le corps.
BLUETOOTH® The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Combustion, Inc. is under license. Other trademarks and trade names are those of their respective owners.
BATTERY WARNING Do not dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery that can result in an explosion.
Do not leave a battery in an extremely high temperature environment that can result in an explosion or leakage of flammable liquid or gas.
Do not expose the battery to extremely low air pressure that may result in an explosion or leakage of flammable liquid or gas.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
Predictive Thermometer CI-PTK-101-Y FCC ID: 2A88P-1004 IC ID: 29707-1004
WiFi Booster CI-CR-101-Y FCC ID: 2A88P-1005 IC ID: 29707-1005
Operating Frequency Ranges: BLE: 2402-2480MHz WiFi [802.11b, US only]: 2401-2473MHz
Complies with IMDA Standards
DB123456
Documents / Resources
 |
Combustion Inc 2A88P-1005 Predictive Thermometer With WiFi Booster [pdf] User Guide 2A88P-1005, 2A88P-1005 Predictive Thermometer With WiFi Booster, Predictive Thermometer With WiFi Booster, Thermometer With WiFi Booster, WiFi Booster |