Coaster 350134F Wireless Adjustable Base

Overview
The 350134F Wireless Adjustable Base lets you raise and lower the backrest and footrest using the included remote control, with optional preset memory positions and a flat-position function.
Specifications
| Input power | AC 100–240V, 50/60Hz |
| Output power | DC 29V, 2.0A |
| Maximum weight capacity | 700 lbs |
| Motor life | 25,000 cycles |
| Mattress requirements | Any sponge mattress can be used |
| Warranty | 2-Year Parts and Labor on entire base |
Parts List
ALL ELECTRONICS AND COMPONENTS THAT NEED TO BE INSTALLED ARE LOCATED IN BOXES UNDER THE FOUNDATION OR ATTACHED TO THE FRAME. BEFORE DISCARDING THE PACKING MATERIALS, ENSURE THAT ALL THE PARTS ARE ACCOUNTED FOR.
- Mattress Rail (1)
- Adjustable-Height Legs (6)
- Remote Control (1)
- Power Supply (1)
- Power Cable (1)
- AAA Batteries (2)

Setup & Use
- Use two people to set up, move, or flip the base.
- Open the carton while the bed is in the flat position, cut it open, and remove the parts boxes and mattress rail.
- Assemble the legs: insert the screw through the triangular brace, attach each leg (6 legs total), and tighten securely.
- Connect wiring: connect the wire from the bed to the jack on the power supply box; connect the AC power cable to the other jack; plug the AC power cable into a nearby power outlet.
- Insert the remote batteries (2 AAA). Press and hold the HEAD UP button; if the motor runs, unplug and turn the bed to the correct right-side-up position. If it does not run, re-pair the remote.
- If needed, pair the remote using the remote pairing procedure (place remote next to the blue RESET button, press/hold HEAD DOWN + FOOT UP, then press/hold the blue RESET until you hear a beep, and release).
- Insert the mattress rail at the foot of the bed.
- Use the remote to adjust the backrest and footrest (press and hold HEAD UP/HEAD DOWN and FOOT UP/FOOT DOWN, and release when the desired position is reached).
- To save a preferred position: flatten the bed, adjust to your preferred position, then press and hold the M button until you hear a beep.
- To return to flat, press the FLAT button.
Safety Precautions
- Power Supply:
- Input: AC 100–240V, 50/60Hz
- Output: DC 29V, 2.0A.
- Maximum Weight Capacity: 700LBS.
- Motor Life: 25,000 cycles.
- Mattress Requirements: Any sponge mattress can be used.
- Pinch /Entrapment Warning: Pinch/entrapment warning labels are provided on the bed. Keep hands, feet, and other body parts clear of moving parts during operation.
- Cleaning: Unplug the product from the power outlet before cleaning.
- Keep Away from Heat: Keep the power cord, power supply, and control box away from heat sources.
- Keep Dry: Do not use the product in a humid environment. Do not allow the wire connectors or the area between the motor and control box to come into contact with water, liquids, or excessive moisture.
- Inspect Before Use: Do not operate the product if the power cord or plug is damaged, or if the product is not functioning properly.
- Extended Periods of Non-Use: Return the product to the flat position, unplug the po wer cord, and remove the batteries from the remote control when the product will not be used for an extended period.
- Medical Advice: Consult your physician if you have any questions or concerns regarding the use of this prod uct.
- Children: Do not allow children to play with or operate this product.
- Children and Pets: Do not allow children or pets underneath the bed.
Electronics Quick Reference Guide


Installation Guide
Safety Warning:
Always use two people when setting up, moving, or flipping the zero-clearance adjustable base.
Note:
To avoid damage to the foundation, always open the carton while the bed is in the flat position.

- Lay the carton flat on the floor and carefully cut it open.

- Lift the carton so the open side faces downward. Slide the carton up and off the bed base. Place the bed base upside down on the floor.

- Remove and discard the plastic bag. Place the two sections of the bed together and align them flat on the floor.

- Cut the zip ties, remove all parts boxes and the mattress rail, and verify that all necessary components are included according to the Parts List.

- For leg (B) assembly, insert the screw through the triangular brace. Attach the leg and tighten the screw securely, ensuring the legs are installed in the correct head and foot positions.

- Connect the wire from the bed to the jack on the power supply (D) box. Connect the AC power cable (E) to the other jack on the power supply box, then plug it into a nearby power outlet.

- Insert the batteries into the remote control (C). Press and hold the HEAD UP button.
- If the motor begins to run, unplug the power supply and, with two people, turn the bed over to its right-side-up position
- If the motor does not run, the remote control needs to be re-paired with the bed.

REMOTE PAIRING
If the remote control does not operate the adjustable these steps to pair the remote with the bed:
- Place the remote control next to the blue RESET button on the power supply box.
- Press and hold the HEAD DOWN and FOOT UP buttons on the remote at the same time.
- While continuing to hold both remote buttons, press and hold the blue RESET button.
- Continue holding all buttons until you hear a beep.
- Release the buttons. The pairing process should take only a few seconds.
- Test the remote by pressing one o f the adjustment buttons.
- If the remote does not pair, check all wire and power connections and rep eat the pairing procedure.
- Insert the mattress rail (A) at the foot of the bed.
Remote Control

Memory Settings
MEMORY POSITION SETTING
USE THE FOLLOWING PROCEDURE TO SAVE A PREFERRED BED POSITION IF YOU ARE NOT SATISFIED WITH THE FACTORY PRESET.
Flatten the Bed
Press the FLAT button to return the bed to the flat position.
Adjust the Bed Position
Adjust the bed to your preferred position by pressing the Head Up/Down and Foot Up/Down buttons.

Save the Memory Position
Press and hold the M button. Release the button after you hear a beep sound, indicating that the preferred position has been successfully saved.
EMERGENCY RESET
- If you are temporarily unable to access the remote control, use the emergency reset button located on the extension wire.
- Press the small button on the extension wire to return the bed to the flat position.

Product size

Troubleshooting
- Remote backlight is dim or does not light: press any remote button to check the blue backlight. If dim/not lighting, confirm both AAA batteries are installed correctly; replace both batteries if needed.
- Power indicator is not lit: check the green power indicator light on the power supply. If it is not illuminated, check the power outlet.
- Movement issues: check for loose wires or connectors.
- Assembly verification: confirm the adjustable bed is assembled according to the installation steps in the manual.
- Remote does not operate (pairing required): verify wiring/power connections and repeat the remote pairing procedure. During pairing, continue holding the remote buttons until you hear a beep, then release and test.
Documents / Resources
![]() | 350134F Wireless Adjustable Base |
References
- User Manualmanual.tools
