CMC Network Analytics Software Installation Guide

CMC LogoCIMC Firmware Version 4.3(2.260007) M5
Update Patch for Secure Network Analytics
v7.5.3

This document provides a description of the CIMC 4.3(2.260007) Firmware M5
Common Update Patch for Secure Network Analytics along with instructions for installing the patch.
This firmware update can be performed using the ISO file/procedure outlined below:
You can use the ISO file, patch-common-SNA-FIRMWARE-20260210-M5- REL.iso, to update the CIMC firmware to version 4.3(2.260007) for UCS C-Series M5 hardware with Secure Network Analytics v7.5.3.
CMC Network Analytics Software - Icon As part of the update process, make sure to install the required rollup patches on your appliances.

M5 Hardware

This patch applies to UCS C-Series M5 hardware for the Secure Network Analytics appliances shown in the following table.

M5 Hardware

Manager 2210 Flow Sensor 1210
Data Node 6200 Flow Sensor 3210
Flow Collector 4210 Flow Sensor 4210
Flow Collector 5210 Engine Flow Sensor 4240
Flow Collector 5210 Database UDP Director 2210

CMC Network Analytics Software - Icon Make sure you update all physical appliances.

Additional Information

For more details about CIMC version 4.3(2.260007), refer to Release Notes for Cisco UCS Rack Server Software.
Download and Installation
Downloading and Installing via ISO
Download
To download the update patch file, complete the following steps:

  1. Log in to Cisco Software Central, https://software.cisco.com.
  2. In the Download and Upgrade area, choose Access downloads.
  3. Type Secure Network Analytics in the Select a Product search box.
  4. Choose the appliance model from the drop-down list, then press Enter.
  5. Under Select a Software Type, choose Secure Network Analytics Patches, then choose Firmware > Firmware in the All Release area to locate the patch.
  6. Download and save the file, patch-common-SNA-FIRMWARE-20260210-M5- REL.iso.
  7. There are two ways of installing ISO:
    o Installation Using vKVM-Mapped vDVD
    o Installation Using CIMC-Mapped vDVD

Before Installation
CMC Network Analytics Software - Icon If you have firewall rules enabled for Cisco Integrated Management Controller (CIMC), specify 169.254.254.2 in the list of allowed hosts to ensure the update is successful. Otherwise you can skip this step and go to Installation Using vKVM-Mapped vDVD or Installation Using CIMC-Mapped vDVD, depending on your preferred installation method.

  1. Log in to the unit’s Cisco Integrated Management Controller (CIMC) interface using a web browser.
  2. Choose Networking > Network Security.
  3. In the IP Filtering (Allow Listing) menu, enter 169.254.254.2 IP value in the IP filter field.
  4. Click Save Changes.

Installation Using vKVM-Mapped vDVD
This installation method updates the firmware by accessing the firmware update ISO file stored on the machine used to connect to the CIMC UI.
To install the firmware patch from an ISO image, use the vKVM console of an M5 machine.

  1. Log in to the unit’s Cisco Integrated Management Controller (CIMC) interface using a web browser.
  2. Click Toggle Navigation icon to display the side menu.CMC Network Analytics Software - Icon 1
  3. Select Compute from the side menu.CMC Network Analytics Software - Compute
  4. Select Remote Management , and then select the Virtual Media tab.
    If there is another file listed in Current Mappings, select it, click Unmap and don’t save the volume. Then, select it again and click Delete to remove it.CMC Network Analytics Software - Compute 1
  5. Select Launch KVM on the toolbar, if prompted, select HTML based KVM.CMC Network Analytics Software - Compute 2
  6. The Virtual Console opens in a new browser tab.CMC Network Analytics Software - Console
  7. Select Virtual Media > Activate Virtual Devices to activate a virtual driveCMC Network Analytics Software - Console 1
  8. If the activation is unsuccessful, repeat the Activate Virtual Devices step.
  9. Once the activation is successful, you can see additional options under the Virtual Media pull-down menu.
  10. Click Map CD/DVD option.CMC Network Analytics Software - Console 2A new window appears, allowing you to browse to the locally stored ISO file. Browse to the ISO file and select it.CMC Network Analytics Software - Map Drive
  11. Click Map Drive to map the virtual drive to the selected ISO file.CMC Network Analytics Software - Map Drive 1
  12. Click Virtual Media drop-down menu to verify that the firmware ISO file is mapped.
    CMC Network Analytics Software - Icon Do not click the mapped file, as this will unmap the file.CMC Network Analytics Software - Map Drive 2
  13. Select Macros > Static Macros > Ctrl-Alt-Del to begin the reboot process.CMC Network Analytics Software - Map Drive 3
  14. Press the F6 key on your keyboard when the Cisco logo and boot messages appear in the KVM virtual console screen.CMC Network Analytics Software - Map Drive 4
  15. When the Please Select Boot Device dialog box appears, select Cisco vKVM- Mapped vDVD1.24.CMC Network Analytics Software - Map DriveThe firmware update initiates. The CIMC may reboot during the update process, causing a temporary loss of connection. If this occurs, log in to the CIMC again and re-launch the vKVM Console to continue monitoring the update. Once the firmware update is complete, the ISO will be ejected or unmounted, and the SNA appliance will reboot.CMC Network Analytics Software - Map Drive 1
  16. Verify on the CIMC Chassis Summary page that the firmware has been updated.

Installation Using CIMC-Mapped vDVD

This installation method updates the firmware by accessing the ISO file stored on an HTTP/S server.

  1. Log in to the unit’s Cisco Integrated Management Controller (CIMC) interface using a web browser.
  2. Click Toggle Navigation to display the side menu.CMC Network Analytics Software - Map Drive 2
  3. Select Compute from the side menu.CMC Network Analytics Software - Map Drive 3
  4. Select Remote Management, and then select Virtual Media.
    CMC Network Analytics Software - Icon If another file is already mapped, select it and click Unmap without saving the volume. Then, select the file again and click Delete to remove it. This will allow you to load the new ISO file.CMC Network Analytics Software - Map Drive 4
  5. Click Add New Mapping button to open Add New Mapping dialog.CMC Network Analytics Software - Map Drive 5
  6. Complete the following fields in the Add New dialog box:
    Enter “HUU” or another meaningful name in the Volume field. This name appears in the Current Mappings window and can help indicate the mapping’s purpose. Example: FW_Patch_2025
    Choose WWW(HTTP/HTTPS) for the Mount Type field.
    CMC Network Analytics Software - Icon If you select another mount type, ensure the corresponding communication port is enabled.
    Enter the file share path of the ISO file in the Remote Share field.
    Example: http[s]://serverip/directory/
    Enter the ISO filename in the Remote File field.
    Select noauto for the Mount Options field.
    Enter User Name and Password, if required.CMC Network Analytics Software - Map Drive 6
  7. Click Save.
  8. In the Current Mappings section, verify that the Status column displays OK and the Mapping Status column displays Mapped.CMC Network Analytics Software - Mapping
  9. Click Save Changes.
  10. Select Launch KVM on the toolbar, if prompted, select HTML based KVM.CMC Network Analytics Software - Mapping 1
  11. The Virtual Console opens in a new browser tab.CMC Network Analytics Software - Mapping 2
  12. Select Macros > Static Macros > Ctrl-Alt-Del to begin the reboot process.CMC Network Analytics Software - Mapping 3
  13. Press the F6 key on your keyboard when the Cisco logo and boot messages appear in the KVM virtual console screen.CMC Network Analytics Software - Mapping 4#When the Please Select Boot Device dialog box appears, select Cisco CIMC-Mapped vDVD1.24.CMC Network Analytics Software - CIMCThe firmware update initiates. The CIMC may reboot during the update process, causing a temporary loss of connection. If this occurs, log in to the CIMC again and re-launch the vKVM Console to continue monitoring the update. Once the firmware update is complete, the ISO will be ejected or unmounted, and the SNA appliance will reboot.CMC Network Analytics Software - CIMC 1
  14. Verify on the CIMC Chassis Summary page that the firmware has been updated.

Contacting Support

If you need technical support, please do one of the following:

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: https://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)

CMC Logo 1© 2026 Cisco Systems, Inc. and/or its affiliates.
All rights reserved.

Documents / Resources

PDF thumbnailNetwork Analytics Software
Installation Guide · Network Analytics Software

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.