Finesse Virtualization Experience Media Engine Configuration
“
Product Information
Specifications:
- Product Name: Cisco Finesse Virtualization
- Hardware: Virtualization Hardware
- Software: Virtualization Software
- Operating System: Unified Communications Operating System
(Unified OS or UCOS)
Product Usage Instructions
Deploying Virtual Machines for Cisco Finesse:
Perform the following steps in vSphere client to deploy the
Virtual machines:
- Step 1
- Step 2
- Step 3
Changing the Boot Order of the Virtual Machine:
Before you begin: See Unified Communications
VMWare Requirements.
Procedure:
- Step 1
- Step 2
- Step 3
You must change the boot order of the Virtual Machine so that
the system boots off the CD/DVD drive for the install. Perform the
following steps to change the boot order of the Virtual
Machine:
Procedure:
- Step 1
- Step 2
- Step 3
Note: After finishing the installation,
consider changing the boot order back so that the Hard Drive device
is again listed before the CD-ROM device.
FAQ (Frequently Asked Questions)
Q: What operating system does Cisco Finesse Virtualization
use?
A: Cisco Finesse Virtualization runs on the Unified
Communications Operating System (Unified OS or UCOS).
Q: How can I deploy Virtual Machines for Cisco Finesse?
A: You can deploy Virtual Machines for Cisco Finesse by
following the steps outlined in the vSphere client.
“`
Cisco Finesse Virtualization
· Virtualization Hardware, on page 1 · Virtualization Software, on page 1 · Deploying Virtual Machines for Cisco Finesse, on page 1 · Changing the Boot Order of the Virtual Machine, on page 2
Virtualization Hardware
Before you install the Finesse software on any server, you must address the following requirement: · If you are performing a fresh install of Finesse in any deployment, be sure to verify that the virtual machine is also fresh (no previously-installed OS is present in the VM). · If you use SATA 7200 RPM disks in your server, you must configure the datastore as RAID 10.
Virtualization Software
All Finesse servers run on VMs using the Unified Communications Operating System (Unified OS or UCOS). See https://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/uc_system/virtualization/ virtualization-software-requirements.html.
· Finesse ISO or DVD
Note You must install Finesse by configuring a DataStore ISO file on the virtual CD or DVD drive of the target VM.
· ESXi must be installed prior to the installation of Cisco Finesse.
Deploying Virtual Machines for Cisco Finesse
Perform the following steps in vSphere client to deploy the Virtual machines:
Cisco Finesse Virtualization 1
Changing the Boot Order of the Virtual Machine
Cisco Finesse Virtualization
Before you begin
See Unified Communications VMWare Requirements.
The following software requirements apply specifically to Finesse:
· For other third-party software requirements and for a list of approved UCS servers, see the server requirements and version compatibility with Unified CM sections in the Cisco Unified Contact Center Enterprise Design Guide available at http://www.cisco.com/en/US/products/sw/custcosw/ps1844/products_implementation_design_guides_list.html.
Procedure
Step 1 Step 2 Step 3
Step 4 Step 5 Step 6
Step 7 Step 8 Step 9
Highlight the host or cluster to which you wish the VM to be deployed. Select File > Deploy OVF Template. Click the Deploy from File radio button and specify the name and location of the file you downloaded in the previous section OR click the Deploy from URL radio button and specify the complete URL in the field, then click Next. Enter the name of the VM machine that you are creating and the location where it will be created. Choose the type of deployment (Production or Lab). Choose the datastore on which you would like the VM to reside (ensure there is sufficient free space to accommodate the new VM), then click Next. Verify the deployment settings, then click Finish. Update boot order as per instructions as specified in the topic Changing the Boot Order of the Virtual Machine. Insert the Finesse disk and follow the instructions specified in the topic Cisco Finesse Server Installation.
Changing the Boot Order of the Virtual Machine
You must change the boot order of the Virtual Machine so that the system boots off the CD/DVD drive for the install. Perform the following steps to change the boot order of the Virtual Machine:
Procedure
Step 1 Step 2 Step 3 Step 4 Step 5
Step 6 Step 7 Step 8
In VMware vSphere Client, power off the virtual machine onto which you deployed the OVA . In the left pane of vSphere Client, right-click the name of the virtual machine, and select Edit Settings. In the Virtual Machine Properties dialog box, select the Options tab. In the Settings column, under Advanced, select Boot Options. Under Force BIOS Setup, check The Next Time the Virtual Machine Boots, Force Entry into the BIOS Setup Screen check box. Click OK to close the Virtual Machine Properties dialog box. Power on the virtual machine (the virtual machine boots into the BIOS menu). Navigate to the Boot menu and change the boot device order so the CD-ROM device is listed first and the Hard Drive device is listed second.
Cisco Finesse Virtualization 2
Cisco Finesse Virtualization
Changing the Boot Order of the Virtual Machine
Step 9
Save the change and exit BIOS setup.
Note After finishing the installation, consider changing the boot order back so that the Hard Drive device is again listed before the CD-ROM device.
Cisco Finesse Virtualization 3
Changing the Boot Order of the Virtual Machine
Cisco Finesse Virtualization
Cisco Finesse Virtualization 4
Documents / Resources
 |
CISCO Finesse Virtualization Experience Media Engine Configuration [pdf] Instruction Manual cfin_m_1501, Finesse Virtualization Experience Media Engine Configuration, Finesse Virtualization, Experience Media Engine Configuration, Engine Configuration, Configuration |