CISCO 1532I-E Aironet Access Point User Guide

1532I-E Aironet Access Point

Product Information

Specifications:

  • Filesystem Name: Flash
  • Filesystem Size: 519 M (bytes)
  • Total Files: 95
  • Data Wipe Time: Fri Mar 8 09:50:49 UTC 2024
  • Data Wipe Method: CLEAR
  • Files Cleared: 92
  • Bytes Cleared: 5484544 (bytes)
  • Total Free Byte: 458846208 (bytes)
  • Device PID: C9130AXI-E
  • Serial Number: KWC233202MN
  • Data Wipe Status: SUCCESS

Product Usage Instructions

How to Perform Secure Data Wipe:

  1. Access the Cisco AP command line interface.
  2. Run the command: clear ap config.
  3. To check the data wipe output, use the command: show flash
    wipeout-log.

Note:

Press the note button for a duration of 20 to 60 seconds to
remove storage content.

Frequently Asked Questions (FAQ)

Q: What does the Secure Data Wipe feature do?

A: The Secure Data Wipe feature allows you to securely erase
files from the file system of Cisco APs using the clear ap config
command. It ensures that the erased files cannot be recovered.

Q: How can I verify if the data wipe was successful?

A: To verify the success of the data wipe, run the command show
flash wipeout-log on the AP and check the Data Wipe Status, which
should indicate SUCCESS if the wipe was completed successfully.

“`

Secure Data Wipe

· Secure Data Wipe, on page 1

Secure Data Wipe

The Secure Data Wipe feature allows you to securely erase files from the file system of Cisco APs by using the clear ap config command. This new command triggers a secure data wipe in an AP. Additionally, this feature also stores basic information about the wipeout along with the wipeout status. The data stored in the AP flash helps to verify the files erased from the AP file system, and troubleshoot issues. Use the clear ap config to view the wipeout history details.
The following files are securely erased, without scope of recovery:
· Configuration and backup configuration files
· Crash files
· Log files
· Boot variables
· Package logs

To check the output of the data wipe, run the following AP command:

Cisco-AP# show flash wipeout-log

DATA SANITATION LOGS

Filesystem Name : Flash

Filesystem size : 519 M (bytes)

Total Files

: 95

Data Wipe Time

: Fri Mar 8 09:50:49 UTC 2024

Data Wipe method : CLEAR

Files cleared

: 92

Bytes cleared

: 5484544 (bytes)

Total Free byte : 458846208 (bytes)

Device PID

: C9130AXI-E

Serial number

: KWC233202MN

Data Wipe Status : SUCCESS

Secure Data Wipe 1

Secure Data Wipe

Secure Data Wipe

Note

· Data wipe for APs in Work Group Bridge mode can be done only through the mode button, which needs

to be pressed for a duration of 20 to 60 seconds to remove storage content.

· Cisco Wave 1 APs are supported in Cisco IOS XE Amsterdam 17.3 and Cisco IOS XE Cupertino 17.9.3 and its later versions. Cisco Wave 1 APs are not supported in 17.4, 17.5, 17.6, 17.7, 17.8, 17.10 and later releases.

· Cisco Wave 2 APs are supported in Cisco IOS XE Dublin 17.11 and Cisco IOS XE 17.13.

· Cisco Wave 1 APs and Cisco Wave 2 APs are supported in Cisco IOS XE Dublin 17.12.

Table 1: Supported AP models
Cisco IOS APs 3700 (I/E/P)

Cisco COS APs 3800 (I/E/P)

2700 (I/E) 1700I 702W 1532I/E 1570 — — — — —

2800 (I/E) 1815 (I/W) 1840 (I) 1850 (I/E) 1830 (I/W) 1810 1800I 1540 1560 4800

Cisco Catalyst APs 9162I 9164I 9166I 9166D1 9163E 9124AX (I/D/E) 9136I 9130AX (I/E) 9120AX (I/E) 9117AXI 9115AX (I/E) 9105AX (I/W) — — —

Secure Data Wipe 2

Documents / Resources

CISCO 1532I-E Aironet Access Point [pdf] User Guide
3700, 3800, 2700, 1700I, 702W, 1532I-E, 1570, 2800, 1815, 1840, 1850, 1830, 1810, 1800I, 1540, 1560, 4800, 9162I, 9164I, 9166I, 9166D1, 9163E, 9124AX I-D-E, 9136I, 9130AX I-E, 9120AX I-E, 9117AXI, 9115AX I-E, 9105AX I-W, 1532I-E Aironet Access Point, 1532I-E, Aironet Access Point, Access Point

References

Leave a comment

Your email address will not be published. Required fields are marked *