CHUANGO DML-100 Multipurpose Sensor
Product Introduction
This multipurpose sensor can be used by connecting to AC power or wirelessly by built-in battery (after it is fully charged). There are two preset working modes: Away Mode and
Home Mode. Easily switch the modes or set schedules to switch on the app.
Please charge it 7-8 hours before use.
In Away Mode, once the sensor detects human movement, the built-in siren sounds, the LEDs flash, and an app push notification will be sent to you.
In Home Mode, when the sensor detects human movement and the surrounding brightness is dark or slightly dark, the LEDs will automatically turn on as a night light.
Ambient light sensing function is default on. If it is toggled off, the LEDs will turn on anytime when motion is detected.
In Away and Home Mode, you can choose to set temperature, humidity and ambient light detecting range, get notified when values exceeding the preset value.
In Away Mode, turn on smoke alarm sound detection function, you’ll be notified when your home’s smoke alarm goes off.
- Connect to Wi-Fi directly, no hub needed.
- Set schedules to switch between modes.
Product Overview
Power On the Sensor
Press and hold the configuration button for 3 seconds to turn the sensor on/off.
Download DreamCatcher Life App
After the device is powered on, add it via Bluetooth or via Wi-Fi AP mode.
Network Setup
Bluetooth: Select Bluetooth toggle to turn it on, it will automatically search for the device.
Tap to add it to your home Wi-Fi network.
Wi-Fi AP mode: Tap Add Device or “+”in the upper right corner, then select DML-100 under “Security” .
Press and hold the Configuration Button for 3 seconds to power on the device, wait for the device to complete a 40-seconds self-test until the indicator light gradient flashes.
Short press the Configuration Button 3 times, the device will enter the WiFi configuration state. The breathing light goes off to indicate the configuration is successful.
| Operation | Light Status | Meaning | Prompt Tone |
| Press and hold the configuration button for 3 seconds |
On |
Sensor is powered on |
Power on tone |
| Press and hold the configuration button for 3 seconds |
Off |
Sensor is powered off |
Power off tone |
| / | Flash on and off for 40 seconds | Device self-test | / |
| Press the configuration button 3 times | Gradient flashing | Device is under
configuration state |
Beep once |
| / | Gradient flashing off | Successfully connected to the network | Beep twice |
| Press the configuration
button 5 times |
On for 1 second then gradient flashes (configuration mode) | Device reset | Long beep once |
Note: Deleting the sensor on the APP while it’s online will also reset it.
Installation
There are two ways to install the sensor: mount it on the wall or place it on desktop.
On Desktop
Put the sensor on a flat surface with the provided desktop bracket.
Wall Mount
To get optimal detection coverage, check the following factors before mounting:
- Determine the area of detection and ensure there is no obstructed field of view.
- Determine the height and adjust angle.
- Avoid direct sources of heat or sunshine, swinging objects like curtains.
Pet-Immune Function
The motion sensor should be mounted 2-2.2m above the floor and adjust the detecting angle according to your need. When the sensor is installed parallel to the wall, pet under 25kg will not trigger alarm.
Note: when the sensor is put on desktop. The pet-immune function could not work as it intends.
Sensitivity
The sensitivity can be adjusted on the app. The default setting is medium sensitivity.
Mount the Sensor
Use the 3M Double-side Adhesive Tape
Remove the adhesive tape film, and stick one side on the back of the magnetic base, the other side on the wall.
Snap the sensor on the base.
Use the Provided Screws
Place the base against the wall and use a pencil to mark the desired location for mounting.
Drill holes at each marking. Insert anchors into the holes if needed, and fix the base onto the wall with the provided screws.
Snap the sensor back onto the base.
Specifications
- Model: DML-100
- Power Supply: DC 5V (18650 rechargeable battery)
- Standby Time: around 60* days
Under the circumstances of stable network, estimated by 8 nightlight triggers per day and 2 alarm triggers per month. If the network is unstable or the signal is poor, the standby time will be shortened.
- Wireless: Wi-Fi 2.4G
- Detection Scope: 5-10 meters
- Detection Angle: 95°max.
- Pet Immunity: <25kg
- Casing Material: PC+ABS
- Operating Temperature: 0°C to 50°C
- Operating Humidity: 0-90% RH
- Sensor Dimensions (L x W x H): 85 x 85 x 84.5 mm
- Bracket Dimensions (L x W x H): 98.5x 98.5 x 101.5 mm
CE Declaration of Conformity
Hereby, Chuango AIoT GmbH declares that the radio equipment type DML-100 is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
INFORMATION FOR THE USERS At the end of its life, the device has to be separated from the other waste. Consign the device and all its components together to a center of electronical and electrotechnical waste recycling center, designated by your local authorities.
2006/66/EC and its amendment 2013/56/EU (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Documents / Resources
 |
CHUANGO DML-100 Multipurpose Sensor [pdf] User Manual DML-100 Multipurpose Sensor, DML-100, Multipurpose Sensor, Sensor |
