DT B Robotic Pool Cleaner
“
Specifications:
- Product Name: CHASING DT B Robotic Pool Cleaner
- Operating Depth: 0.5-3 meters
- Working Temperature: 5-35°C
- pH Range: 7-7.8
- Salt Tolerance: Max. 5,000 ppm
- Chlorine Tolerance: Max. 4 ppm
Product Usage Instructions:
Precautions:
- Read the User Manual carefully before operation.
- Operate the product according to the provided
instructions. - Do not disassemble or repair the product unless by authorized
professionals. - Avoid using the Cleaner in extreme temperatures or direct
sunlight. - Keep children supervised while using the product.
- Avoid damaging the internal structure of the Cleaner.
- Use the Cleaner only in pool water.
Main Components:
The main components of the Cleaner include:
- Slide switch (ON/OFF)
- Mode indicator
- Filter basket
- Handle
- Water outlet
- Drive wheel
- Active brush
- Water inlet
- Driven brush
- Charging port
- Salvage hook
Charging and Operation:
Charging:
- Do not drain the battery completely.
- Charge if State of Charge (SOC) is less than 5%.
- Maintain SOC at 50%-70% when idle.
- Operating temperature range: 5-35°C.
Operation:
- To power ON, slide the switch to ON position.
- To power OFF, slide the switch to OFF position.
- To switch modes, toggle between ON and OFF within 5
seconds.
The Cleaner supports three modes: Auto, Floor, and Wall, each
serving different cleaning purposes as described in the manual.
FAQ:
Q: Can the Cleaner be used with liquid flocculant or clarifying
agents in the pool water?
A: It is not recommended to use the Cleaner with these agents as
they may block or damage the filter.
Q: What should I do if the Cleaner’s battery is damaged?
A: Do not use the Cleaner again if its internal structure is
damaged. Contact authorized professionals for repair.
Q: Can children operate the Cleaner without supervision?
A: No, children should not use the product without parental
supervision.
“`
CHASING DT B
Robotic Pool Cleaner
EN User Manual
www.poolmatebot.com
V1.0
Table of Contents
EN Disclaimer ································· 01 Precautions ······························· 02 Main Components··························· 03 Cleaner ····································· 03 Power adapte·r································· 04 Charging and Operation ······················ 04 Charging ···································0·4 Operation and Application ························· 05 Indicator Definition······························ 06 After Cleaning ································· 06 APP ······································ 09 Download of CHASING GO3 APP ····················· 09 Bluetooth Connection···························· 09 Home ······································ 10 Preset······································ 10 Me ········································ 11 Routine Maintenance ························ 11
Troubleshooting ···························· 12 Product Parameters ························· 13 After-sales ································· 13
Disclaimer
Please read this Disclaimer carefully before using CHASING DT B.
EN
By using the product, it shall be deemed as the approval and acceptance of all contents of this disclaimer.
CHASING will not be liable for any personal injury or property damage (including direct or indirect damage) caused by the following reasons when using this product:
1. Damages due to the operation by the operator in poor physical or mental condition, 2. Personal injury and property loss caused by the subjective intention of the operator, 3. Compensation for any damage arising from accidents, 4. Failure to follow the correct guidance of this Manual to assemble or operate the product, 5. Other damage caused by improper operation of the Cleaner due to self-modification or replacement with accessories or parts not manufactured by CHASING, 6. Damages caused by using products not manufactured by CHASING, 7. Compensation for damages caused by operation error or subjective judgment error of the operator, 8. Improper operation caused by natural wear, corrosion, wire aging and other problems of the Cleaner, and 9. Other losses not covered in the scope of responsibilities of CHASING.
01
Precautions
EN
Warning: Please read the User Manual carefully, and operate the product according
to the instructions herein. The Company will not be responsible for any losses or
injuries caused by improper operation.
Warning: The parts of this product can only be disassembled and repaired by authorized and trained professionals of the dealer, otherwise warranty will be invalid and personal injury may be caused.
Warning: If the Cleaner is used at temperatures higher than the specified operating temperature or exposed to intense sunlight for a long time, the high-temperature protection will be triggered, making them powered off, or in severe cases, causing damage to the product.
Warning: Children are not allowed to use this product without supervision by their parents.
Warning: Do not open, crush, heat or burn the battery case in the Cleaner to avoid the risk of fire and burn.
Warning: Do not use the Cleaner again if its internal structure is damaged.
The Cleaner cannot be used in other working environments but only in the water of the pool. No one is allowed to enter the pool while the Cleaner is working.
Main Components
Cleaner
EN
3
2
1
4
5 6
Do not touch the rotating part directly with your hands while the Cleaner is working.
7
8
8
10
9
1. Slide switch (ON/OFF)
Do not use this product in the pool if liquid flocculant or other clarifying agents are added in the water, because the filter of the Cleaner may be blocked or damaged.
2. Mode indicator 3. Filter basket 4. Handle
Please use the Cleaner in the following calibrated environment:
5. Water outlet
6. Drive wheel
11
Operating depth Working temperature pH
0.5-3 m 5-35 7-7.8
7. Active brush 8. Water inlet 9. Driven brush 10. Charging port
Salt
Max. 5,000 ppm
11. Salvage hook
Chlorine
Max. 4 ppm
02
03
Power adapter
EN
1. Power adapter 2. AC power cord
Charging and Operation
1 Charging
5. Battery protection:
EN
Please do not drain the battery
Please charge if the SOC is less
than 5%.
Keep the SOC at 50%-70% when
idle.
Operating temperature:
5-35
2 Operation and Application
1. Power ON: Slide the switch button to the “ON” mark to turn on the Cleaner, and the indicator will be steady on.
1. Please charge the Cleaner with the official standard power adapter of CHASING. 2. Dry the water on the charging port of the Cleaner before charging. 3.Align the charger with the anti-misconnection design of the charging port and insert it correctly. 4. If the power adapter indicator is in red, the charging is in progress; if in green, the charging is completed. After charging, unplug the adapter in time. 5. Reinstall the rubber plug after charging to prevent water from entering. 6. Before charging, please use a dust blower to remove any moisture and dust from inside the charging port.
Precautions
1. As the long-term storage will accelerate the self-discharge and passivation of active substances, it is recommended to fully charge and discharge the Cleaner every three months to reduce the negative impact of long-term storage, and then restore its original performance. 2. The lithium battery of this product is not replaceable, so it should be recycled by a qualified battery recycling station, rather than being discarded in the trash can. 3. Do not place the device vertically for charging to prevent water from entering the charging port. 04 4.Do not charge indoors.
2. Power OFF: Slide the switch button to the “OFF” mark to turn off the Cleaner, and the indicator will be off.
05
3. Mode switching: Switch from ON to OFF and then to ON (ON OFF ON) within 5 seconds.
EN
1 2
The Cleaner supports three modes: Auto, Floor and Wall. In Auto mode, the Cleaner can clean the floor, walls and lane lines, as well as at least 80% of the floor area, and can thoroughly clean a standard pool. In Floor mode, the Cleaner mainly cleans the pool floor, improving the efficiency of floor cleaning. In Wall mode, the Cleaner can effectively clean the walls and lane lines, significantly reducing uncleaned area.
4. After power-on, put the Cleaner into the pool, and get it to start cleaning after reaching the pool floor. At the moment, the indicator is in breathing state.
4 After Cleaning
1. The Cleaner will move to the pool edge and stop cleaning automatically when the battery life is lower than 5%.
EN
2. Please bring it out of the pool with the salvage hook. 2.1 The user can connect the salvage hook provided in the package to any standard pool cleaning rod to extend the reach of the salvage.
3 Indicator Definition
Working State Standby Cleaning Abnormal Cleaner Check for Upgrades/Self Check SOC: 80% SOC: 20-79% SOC: < 20% Shutdown Charging/not fully charged Fully charged/not charged
Light Status Steady On (The color changes with battery level) Breath (The color changes with battery level) Flash in Red Blue breathing Green Blue Red Off The red light of the charger is steady on The green light of the charger is steady on
06
42MM
28.3MM 33MM
2.2 Schematic Diagram of Salvage Hook Connection to the Pool Cleaning Rod
1
2
07
2.3 Hook the Cleaner’s handle with the salvage hook to pull the Cleaner out of water.
EN
4. Slide the switch button to the “OFF” mark to turn off the Cleaner.
EN
3. Hold the Cleaner’s handle and pull it out of water, and hang it on the water for 5-10 seconds to drain the water inside.
APP
1 Download the CHASING GO3 APP
CHASING GO3 APP: Support iOS 11.0 and above, and Android 7.0 and above. You can download the App by scanning the QR code, or by visiting the iOS App Store, Google Play, and CHASING’S website.
2 Bluetooth Connection
1. Select “CHASING DT B”on the”Device Selection”page.
2. Click “Get to Connect”.
3. When finding a new device, click on it to connect, and then enter the “Home” page after successful connection.
CHASING CHASING CHASING CHASING
DT-B model can only be used on ground and cannot access to communication
08
connection under water.
09
3 Home ECN Bluetooth
Connected
Mode Selection
SOC
ECO switch Schedule/Delay
Home
ECO mode
ECO mode is only applicable to Auto/Floor mode and can extend cleaning time by 30% when enabled.
4 Preset
When the Cleaner is in standby state and placed in the pool, it is possible to create Preset Cleaning and complete unmanned operation.
Schedule/Delay
Enter the Create Timer screen
9:41
Create a delay
08
9
09
10
10 11
11
12
12
13
Create a preset cleaning plan
Enter the Create Delay screen to prese(t2a)
Complete the preset cleaning plan
10
schedule/delay.
5 Me
Firmware Upgrade Portal SN Inquiry Portal
EN
Routine Maintenance
Clean the filter screen.
2
1
4 3
* To ensure the cleaning performance of the Cleaner, it is recommended to replace the filter screen at least every three months during use.
11
Save
If the Cleaner will not be used for a long time, please follow the following steps:
CEN 1. Clean the filter basket thoroughly and place it inside the Cleaner;
2. Make sure there is no water left in the Cleaner; 3. Charge the Cleaner and then turn off; 4. Store indoors in a cool and dry place at 5-45.
Troubleshooting
Faults The Cleaner cannot be charged. The battery is not fully charged.
The Cleaner is not started up.
The Cleaner moves but fails to clean the pool effectively.
The Cleaner cannot climb walls.
The Cleaner only cleans a portion of the pool
Possible Causes The charger is in poor contact The Cleaner is not turned off after charging, resulting in normal standby electricity loss.
The Cleaner is not put in water.
The track is stuck by foreign object The SOC of the battery is too low.
The filter basket is blocked
The impeller is blocked by foreign object The SOC of the battery is too low.
The filter basket is blocked The impeller is blocked by foreign object The temperature or pH value is inappropriate
There is algae on walls
The SOC of the battery is too low.
The filter basket is blocked
There are obstacles in the pool
Troubleshooting Dry the charging contacts of the Cleaner and check for damage.
Check whether the Cleaner is turned off after charging.
Put the Cleaner into water. Check whether the track tire is stuck and remove foreign object
Charge the Cleaner
Clean the filter basket Check whether the impeller is blocked and remove foreign object Charge the Cleaner
Clean the filter basket Check whether the impeller is blocked and remove foreign object Use the Cleaner in a pool with the required temperature and pH Check the chemical level in the water and scrub the walls
Charge the Cleaner
Clean the filter basket
Remove obstacles
12
Product Parameters
Cleaner dimensions
398 * 405 * 253 mm
EN
Cleaner weight
7.5 kg
Battery Capacity
11000 mAh
Battery endurance
200 min (ECO mode 300 min)
Average power
100 W
Input power
Max. 170W
Charging time
4 h
Operating depth
0.5-3 m
Optimum applicable area
150-200
Cleaning zone
Floor, wall, lane line
Filtering flow
Up to 420 L/min
Filtering accuracy
180 m
Moving speed
11m/min
Filter basket volume
4.1L
Active brush
Support
APP
Support
Cloud Service
Not supported
After-sales
In case of any questions or technical problems, please send email to CHASING after-sales personnel or contact E-chat personnel on the official website. After-sales E-mail address:
support01@poolmatebot.com–Europe support02@poolmatebot.com –Asia & Oceania support03@poolmatebot.com– North and South Americas & Africa 2. You can view the teaching videos in App menu, official website and official WeChat account to get better experience.
The Manual is subject to change without prior notice.
The latest version is also available from CHASING official website: https://www.poolmatebot.com.
13
Documents / Resources
 |
CHASING DT B Robotic Pool Cleaner [pdf] User Manual DT B, DT B Robotic Pool Cleaner, Robotic Pool Cleaner, Pool Cleaner, Cleaner |