Ang lcdwiki E32R40T LCD Touch Screen Display
Mga detalye
- Product Name: LCDWIKI 4.0inch ESP32-32E E32R40T&E32N40T
- Display Module: 4.0inch ESP32-32E
- Numero sa Modelo: CR2025-MI3275
- Website: www.lcdwiki.com
Kusug sa produkto
Gamita ang Type-C cable nga adunay power supply ug data transmission function aron makonektar ang computer ngadto sa produkto ug ma-power ang produkto. Ingon sa gipakita sa litrato sa ubos:
I-install ang USB-to-serial port driver
- Locate the USB-SERIAL_CH340.zip package in the “7-工具软件_Tool_software” folder and decompress it.
- go to the folder after decompression, double-click “CH341SER.EXE” executable program, pop up the installation window, and then click “Install” button to continue the installation, as shown in the following picture:
After the installation is successful, click the window OK button to exit. Connect the computer USB to the development board and power on, and then enter the computer device manager, you can see that the CH340 port is identified under the port, as shown in the following picture:
Sunoga ang bin file
- Open the “Flash_Download” folder in “8-快速使用_Quick_Start”, locate the “flash_download_tool” folder, open the folder, and double-click the exe executable file sa flash_download_tool. Ingon sa gipakita sa litrato sa ubos:
- After opening the Flash download tool, ChipType select “ESP32”,WorkMode select “Develop”,LoadMode keep the default (UART), and then click “OK” button, as shown below:
Pagsulod sa Flash download tool interface, una pilia ang bin file sa pagsunog, bin file in the data package “8-快速使用_Quick_Start /bin” directory, as shown in the following figure:
- I-klik ang buton nga adunay tulo ka tuldok sa tunga aron mapili ang bin file sa mga lakang sa ibabaw. Human sa pagpili, susiha ang kahon sa atubangan ug itakda ang nagdilaab nga adres isip "0", ingon sa gipakita sa mosunod nga hulagway:
- Set SPI SPEED to “80MHz”, SPI MODE to “DIO”, and keep other Settings default, as shown in the following figure:
- Set COM, as long as the product is normally connected to the computer, COM port will be automatically recognized, click the drop-down menu to select. Set BAUD, click the drop-down menu to select, the larger the value, the faster the burning speed, but can not exceed the maximum transmission rate supported by the USB-to-serial chip. As shown in the picture below:
- Click the “START” button to enter the burning state. During the burning process, the status changes: “Waiting for synchronous power-on” -> “Downloading” -> “FINISH”, and the progress bar will also be loaded, as shown in the following picture:
Pagdalagan ang programa
Pagkahuman sa Bin file nasunog, i-press ang reset button sa produkto o power sa produkto pag-usab, ug imong makita ang operasyon nga epekto sa programa, sama sa gipakita sa hulagway sa ubos:
Kanunay nga Gipangutana nga mga Pangutana
- Q: Giunsa nako gahum ang produkto?
A: Use a Type-C cable with power supply and data transmission function to connect the computer to the product. - P: Unsaon nako pag-install ang driver sa USB-to-Serial Port?
A: Locate and decompress the USB-SERIAL_CH340.zip package, then run CH341SER.EXE for installation. - P: Unsaon nako pagsunog ang bin file?
A: Open the Flash_Download folder, run flash_download_tool, select ESP32 as ChipType, and follow the steps mentioned in the manual.
Mga Dokumento / Mga Kapanguhaan
 |
Ang lcdwiki E32R40T LCD Touch Screen Display [pdf] Giya sa Gumagamit E32R40T, E32N40T, E32R40T LCD Touch Screen Display, E32R40T, LCD Touch Screen Display, Touch Screen Display, Screen Display, Display |