Ang CISCO ESW6300 Pag-enable sa USB Port sa mga Access Point

Mga detalye

• USB Port Power: Up to 2.5W (some models support up to 4.5W)
• USB Port Function: Tinubdan sa gahum alang sa USB device

Mga Instruksyon sa Paggamit sa Produkto

Pag-enable sa USB Port sa Access Points:
To enable the USB port on your Cisco Access Point for powering USB devices:

1. Check if your AP model supports a USB power source by referring to the datasheet.
2. I-configure ang usa ka AP Profile gamit ang CLI:
   • Pagsulod sa global configuration mode: configure terminal
   • Paghimo og AP profile: ap profile xyz-ap-profile
   • I-enable ang USB para sa AP profile: usb-enable
   • Paggawas sa configuration mode: end
3. I-configure ang mga setting sa USB para sa Access Point gamit ang CLI:
   • Pagsulod sa pribilihiyo nga EXEC mode: enable
   • Enable the USB port on the AP: ap name AP44d3.xy45.69a1 usb-module override

USB Port isip Power Source alang sa Access Points
Some Cisco APs have a USB port that can act as a source of power for some USB devices. The power can be up to 2.5W; if a USB device draws more than 2.5W of power, the USB port shuts down automatically. The port is enabled when the power draw is 2.5W or lower. Refer to the datasheet of your AP to check if the AP has a USB port that can act as a source of power.

Nota 
Both IW6300 and ESW6300 APs have a USB port that can act as a source of power up to 4.5W for some USB devices.

Nota
The controller records the last five power-overdrawn incidents in its logs.

Pagbantay

When an unsupported USB device is connected to the Cisco AP, the following message is displayed:
The inserted USB module is not a supported device. The behaviour of this USB device and its impact on the Access Point are not guaranteed. If Cisco determines that a fault or defect can be isolated due to the use of third-party USB modules installed by a customer or reseller, Cisco may withhold support under warranty or the support program under contract. In the course of providing support for Cisco networking products, the end user may be required to install Cisco-supported USB modules in the event Cisco determines that removing third-party parts will assist Cisco in diagnosing the root cause for troubleshooting purposes. Cisco also reserves the right to charge the customer per the then-current time and material rates for services provided to the customer when Cisco determines, after having provided such services, that an unsupported device caused the root cause of the defective product.

Pag-configure sa usa ka AP Profile (CLI)

Pamaagi

	Sugo o Aksyon	Katuyoan
Lakang 1	i-configure ang terminal Example: Device # i-configure ang terminal	Misulod sa global configuration mode.
Lakang 2	ap profileAP-profilee Example: Device(config)# ap profile xyz-ap-profile	Gi-configure ang usa ka AP profile and enters the AP profile mode sa pag-configure. Nota When you delete a named profile, the APs associated with that profile will not revert to the default profile.
Lakang 3	usb-enable Example: Device(config-ap-profile)# usb-enable	Makapahimo sa USB alang sa matag AP profile. Nota By default, the USB port on the AP is disabled.   Gamita ang no USB-Enable command to disable USB for each AP profile.
Lakang 4	katapusan Example: Device(config-ap-profile)# katapusan	Mibalik sa pribilihiyo nga EXEC mode. Sa laing bahin, mahimo usab nimo i-press Ctrl-Z aron mogawas sa global configuration mode.

Pag-configure sa USB Settings para sa Access Point (CLI)

Pamaagi

	Sugo o Aksyon	Katuyoan
Lakang 1	makahimo Example: Device# makahimo	Misulod sa pribilihiyo nga EXEC mode.
Lakang 2	ngalan sa ap ap-ngalan usb-module Example: Device# ap name AP44d3.xy45.69a1 usb-module	Enables the USB port on the AP. Gamita ang ngalan sa ap ap-ngalan no usb-module Command to disable the USB port on the AP. Nota If you are using a Cisco Catalyst 9105AXW AP and you enable the USB port (3at PoE-in), it is not possible to enable the USB PoE-out at the same time.
Lakang 3	ngalan sa ap ap-ngalan usb-module override Example: Device# ap name AP44d3.xy45.69a1 usb-module override	Overrides the USB status of the AP profile and considers the local AP configuration. Gamita ang ngalan sa ap ap-ngalan no usb-module override command to override the USB status of the AP and consider the AP profile configuration. Nota You can configure the USB status for an AP only if you enable USB override for it.

Pag-configure sa USB Settings para sa Access Point (GUI)

Pamaagi

• Step 1: Choose Configuration >Wireless > Access Points.
• Step 2: In the Access Points window, click the name of the AP.
• Step :3 In the Edit AP window, click the Interfaces tab.
• Step: 4 In the USB Settings section, configure the USB Module State as either of the following:
  • ENABLED: Enables the USB port on the AP
  • DISABLED: Disables the USB port on the AP
• Nota
  If you are using Cisco Catalyst 9105AXW AP and if you enable the USB por3at3at PoE-in, it is not possible to enable the USB PoE-out at the same time.
• Step 5: Configure USB Override as either of the following:
  • ENABLED: Overrides USB status of the AP profile and considers the local AP configuration
  • DISABLED: Overrides USB status of the AP and considers the AP profile configuration
  • Nota
    You can configure the USB status for an AP only if you enable USB override for it.
• Step 6: Click Apply & Update to Device.

Pag-monitor sa USB Configurations para sa Access Points (CLI)

• Sa view the inventory details of APs, use the following command: show ap name ap-name inventory
• Ang mosunod mao angampang output:
  • Device# show ap name AP500F.8059.1620 inventory
  • Device# show ap name AP500F.8059.1620 inventory
• Ang mosunod mao angampang output:
  • NAME: AP280  DESCR: Cisco Aironet 2800 Series (IEEE 802.11ac) Access Point
  • PID: AIR-AP2802I-D-K9 , VID: 01, SN: XXX1111Y2ZZZZ2800
  • NAME: SanDisk, DESCR: Cruzer Blade
  • PID: SanDisk , SN: XXXX1110010, MaxPower: 224
• Sa view the summary of an AP module, use the following command: show ap module summary
• Ang mosunod mao angampang output:
  • Device# ipakita ang summary sa module sa ap
• AP Name External Module External Module PID External Module

Deskripsyon
AP500F.1111.2222 Enable SanDisk Cruzer Blade

• Sa view the USB configuration details for each AP, use the following command: show ap name ap-name config general
• Ang mosunod mao angampang output:
  • Device# ipakita ang ap ngalan AP500F.111.2222 config general
  • USB Module Type……………………………. USB Module
  • USB Module Status………………………….. Disabled
  • USB Module Operational State………………… Enabled
  • USB Override …………………………….. Enabled
• Sa view sthe status of the USB module, use the following command: show ap profile ngalan xyz detalyado
• Ang mosunod mao angampang output:
  • Device# ipakita ang app profile ngalan xyz detalyado
  • USB Module: ENABLED

Mga FAQ

Q: How can I tell if my AP supports a USB power source?

A: You can refer to the datasheet of your AP to check if it has a USB port that can act as a power source for USB devices.

P: Unsa ang mahitabo kung ang usa ka USB device nga konektado makakuha og labaw sa 2.5W nga gahum?

A: If a USB device draws more than 2.5W of power, the USB port shuts down automatically to prevent damage.

Mga Dokumento / Mga Kapanguhaan

Ang CISCO ESW6300 Pag-enable sa USB Port sa mga Access Point [pdf] Manwal sa Instruksyon IW6300, ESW6300, ESW6300 Pag-enable sa USB Port sa Access Points, Pag-enable sa USB Port sa Access Points, USB Port sa Access Points, Access Points

Mga pakisayran

• Manwal sa Gumagamit