CDW-B1800DL-01H WiFi Module
“
Specifications
- Model: CDW-B1800DL-01H WiFi module
- Major Chipset: AIC8800DL
- Standard: 802.11b/g/n/ax
- Frequency Band: 2.4GHz
- WiFi Interface: USB2.0
- BLE Interface: USB2.0
- Storage Temperature: 5% to 90% maximum humidity
- Moisture Sensitivity Level: MSL3
Product Usage Instructions
1. Overview
The CDW-B1800DL-01H module is a highly integrated chip providing
2.4GHz Wi-Fi6 and BLE5.2 for wireless applications.
2. Features
The module offers advanced features for wireless
connectivity.
3. Block Diagram
Illustrates the internal components of the CDW-B1800DL-01H
module.
4. General Specification
- Model Product Name: CDW-B1800DL-01H WiFi module
- Major Chipset: AIC8800DL
- Standard: 802.11b/g/n/ax
- Modulation Method:
BPSK/QPSK/16-QAM/64-QAM/256-QAM/1024-QAM - Frequency Band: 2.4GHz
- WiFi Interface: USB2.0
- BLE Interface: USB2.0
- Storage Temperature: 5% to 90% maximum humidity
5. RF Specification
Detailed specifications related to WiFi and Bluetooth RF
performance.
6. Recommended Operating Rating
Provides information on the recommended operating voltage.
FAQ
Q: What is the frequency range for the WiFi module?
A: The frequency range is from 2.400 GHz to 2.483.5 GHz (2.4 GHz
ISM Band).
Q: What is the Bluetooth standard supported by the module?
A: The module supports Bluetooth Low Energy (BLE) version
5.2.
Q: What is the maximum input level for Bluetooth?
A: The maximum input level for Bluetooth is -90 dBm.
“`
SPECIFCATION
CDW-B1800DL-01H
WiFi module
Software
Customer
Approve
Date
Design
Check
Approve
Version
V1.1
Date
2025.03.18
CHINA DRAGON TECHNOLOGY LIMITED
B4 (86 755) 81449957 (86 755) 81449967 E-mail: Info@cdtech.cn Http://www.cdtech.cn
WiFi Module
CDW-B1800DL
Module Type CDW-B1800DL-00
CDW-B1800DL_Series Module Datasheet
Description AIC8800DL,b/g/n/ax,single band, BW40M,1T1R,wifi(USB2.0)+BT5.2(USB2.0),1-ANT type,no shielding
Remark
CDW-B1800DL-10
AIC8800DL,b/g/n/ax,single band, BW40M,1T1R,wifi(USB2.0)+BT5.2(USB2.0),IPEX-ANT type,no shielding
CDW-B1800DL-00H
AIC8800DL,b/g/n/ax,single band, BW40M,1T1R,wifi(USB2.0)+BT5.2(USB2.0),1-ANT type,no shielding
IC
CDW-B1800DL-10H
AIC8800DL,b/g/n/ax,single band, BW40M,1T1R,wifi(USB2.0)+BT5.2(USB2.0),IPEX-ANT type,no shielding
IC
CDW-B1800DL-01H
AIC8800DL,b/g/n/ax,single band, BW40M,1T1R,wifi(USB2.0)+BT5.2(USB2.0),1-ANT type,Have shielding
Page 1
Reversion History
Version
Date
1.0
2024.06.12
1.1
2025.03.18
WiFi Module
CDW-B1800DL
Modification First release Add CDW-B1800DL-01H module
Page 1
WiFi Module
CDW-B1800DL
1. Overview
The CDW-B1800DL-01H module is a highly integrated chip 2.4GHz Wi-Fi6, BLE5.2 for wireless application.
2. Features
CMOS single-chip fully-integrated RF, Modem and MAC Support 2.4GHz Wi-Fi6 Support 20/40MHz bandwidth Data rates up to 286.8Mbps@TX and 229.4Mbps@RX Support STA, AP, Wi-Fi Direct modes concurrently Support STBC, beamforming Support Wi-Fi6 TWT Support MU-MIMO, OFDMA Support Two NAV, Buffer Report, Spatial reuse, Multi-BSSID, intra-PPDU power save Support LDPC Support DCM, Mid-amble, UORA Support WEP/WPA/WPA2/WPA3-SAE Personal, MFP Supports USB2.0 interface Integrated low power timer and watchdog Supports allthemandatory and optionalfeatures of Bluetooth LowEnergy Supports advanced master and slave topologies Use an optimization method to assess channel quality, AFH enhancement
Page 2
3. Block Diagram
Crystal 26MHz
0.9V
WiFi Module
CDW-B1800DL
1.3V
2.4GHz ISM WL/BT_RF I/O port (shared)
LDO
DC/DC
AICAI8C880800D0DLC
+3.3V USB2.0 PCM GPIO
4. General Specification
Model Product Name
CDW-B1800DL-01H WiFi module
Major Chipset
AIC8800DL
Standard
802.11b/g/n/ax
Modulation Method
BPSK/ QPSK/ 16-QAM/ 64-QAM/256-QAM/1024-QAM
Frequency Band
2.4GHz
WiFi Interface
USB2.0
BLE Interface
USB2.0
Operating Temperature -20° C ~ 70° C
Storage Temperature
-20° C ~ 85°C
Humidity
5% to 90% maximum
Moisture Sensitivity Level MSL3
Page 3
WiFi Module
CDW-B1800DL
5. RF Specification
A. WiFi RF Specification
Feature
Description
WLAN Standard
IEEE 802.11b/g/n/ax WiFi compliant
Frequency Range Number of Channels
Modulation
2.400 GHz ~ 2.483.5 GHz (2.4 GHz ISM Band) 2.4GHzCh1 ~ Ch11 802.11b : DQPSK, DBPSK, CCK 802.11 g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK
802.11 ax : OFDM /256-QAM, 64-QAM, 16-QAM, QPSK, BPSK
Receive Sensitivity (11b,20MHz) @8% PER
Receive Sensitivity (11g,20MHz) @10% PER
Receive Sensitivity (11n,20MHz) @10% PER
– 1Mbps – 2Mbps – 5.5Mbps – 11Mbps – 6Mbps – 9Mbps – 12Mbps – 18Mbps – 24Mbps – 36Mbps – 48Mbps – 54Mbps – MCS=0 – MCS=1 – MCS=2 – MCS=3 – MCS=4 – MCS=5
PER @ -97dBm, typical PER @ -95dBm, typical PER @ -92dBm, typical PER @ -89dBm, typical PER @ -91dBm, typical PER @ -89dBm, typical PER @ -86dBm, typical PER @ -83dBm, typical PER @ -80dBm, typical PER @ -77dBm, typical PER @ -74dBm, typical PER @ -72dBm, typical PER @ -90dBm, typical PER @ -87dBm, typical PER @ -84dBm, typical PER @ -81dBm, typical PER @ -78dBm, typical PER @ -75dBm, typical
Page 4
B. Bluetooth Specification
Feature General Specification Bluetooth Standard Host Interface
Description
BLE5.2 USB
WiFi Module
CDW-B1800DL
Frequency Band
2402 MHz ~ 2480 MHz
Number of Channels
BLE:40 channels
RF Specification
Output Power, tolerance±2dBm
Sensitivity, tolerance±2dBm Sensitivity @ BLE=30.8% for LE(1Mbps) Sensitivity @ BLE=30.8% for LE(2Mbps)
Maximum Input Level
-90 dBm
-91 dBm GFSK(1Mbps): -20 dBm GFSK(2Mbps): -20 dBm
6. Recommended Operating Rating
symbol
Parameter
Minimum Typical
VDD 3.3V supply voltage
3.0
3.3
VDDIO I/O supply voltage
1.7
1.8
Current 3.3V rating current
—
—
Maximum 3.6 1.9 800
Units V V mA
Page 6
7. Footprint Dimension
7.1 No IPEX Footprint Dimension
12.2±0.2
1
14
11..980±±0.02.2
13±0.2
4
11
TOP VIEW
SIDE VIEW
7.2 IPEX Footprint Dimension
12.2±0.2
2.25±0.2
1
14
13±0.2
4
11
TOP VIEW
SIDE VIEW
13±0.2
13±0.2
3.53
2.16
2.98
2.00 2.33
3.53
2.16
2.98
2.00
2.33
WiFi Module
CDW-B1800DL
2.83
2.50
3.50
12.2±0.2
3.40
5*1.27
2.45
20 19 18 17 16 15
0.80
0.70
0.70
1.00 0.80
1
14
2 13
3 1.20
1.20
1.20
12 4
1.20
1.00
0.80
0.70
11
5 6 7 8 9 10
3.40
5*1.27
2.45
TOP VIEW
2.80
1.37
Unit:mm
2.83
12.2±0.2
3.40
5*1.27
2.45
1.00 0.80
20 19 18 17 16 15
0.80
0.70
0.70
1
14
2 13
2.50
3.50
1.37 2.80
3 1.20
1.20
12 4
1.20
1.00
1.20
0.80
0.70
11
5 6 7 8 9 10
3.40
5*1.27
2.45
TOP VIEW
Page 7
13±0.2
WiFi Module
CDW-B1800DL
7.3 No IPEX have shielding footprint Dimension
2.16 2.98 2.00 2.33
12.2±0.2
1
14
2.4±0.2
2.50
2.83
Unit:mm
12.2±0.2
2.45
5*1.27
3.40
1.000.80
15 16 17 18 19 20
0.80
0.70
0.70
14
1
2 13
13±0.2
3.50
3.53
1.37 2.80
3
1.20
1.20
12
4
4
11
1.20
1.20
0.80
1.00
11
0.70
10 9 8 7 6 5
2.45
5*1.27
3.40
TOP VIEW
SIDE VIEW
BOT VIEW
8. Pin Description
20 WL_WAKE_HST
19 HST_WAKE_WL
18 CHIP_EN
17 NC
16 TXD0
15 RXD0
1 GND
2 RF_0
3 RF_1
4 GND
14 GND
13 USB_DP
12 USB_DM
11 VIN
5 PCM_IN
6 PCM_OUT
7 PCM_SYN
8 PCM_CLK
9 BT_WAKE_HST
10 HST_WAKE_BT
NO
Name
Description
1
GND
Ground connections
2
RF0
RF0 I/O port ;When have IPEX the PIN is NC
3
RF1
NCKeep Floating
Page 8
WiFi Module
CDW-B1800DL
4
GND
Ground connections(Note: The PIN must be connected to GND)
5
PCM_IN
BLE_PCM data Input . This pin is also shared with GPIOA2.
6
PCM_OUT
BLE_PCM data Output . This pin is also shared with GPIOA3
BLE_PCM frame Synchronization. This pin is also shared
7
PCM_SYNC
with GPIOA0.
8
PCM_CLK
BLE_PCM Clock. This pin is also shared with GPIOA1.
9
BT_WAKE_HOST BLE Wakeup Host pin. This pin is also Shared with GPIOB2.
10
HOST_WAKE_BT Host Wakeup BLE pin. This pin is also shared with GPIOB3.
11
VCC
Power supply 3.3V is required
12
USB_DM
High-Speed USB D- Signal
13
USB_DP
High-Speed USB D+ Signal
14
GND
Ground connections
15
RXD0
Floating, Debug pin
16
TXD0
Floating, Debug pin
17
NC
Floating
18
Chip_en
Low closed.
19
HOST_WAKE_WLAN Host Wakeup WLAN pin. This pin is also shared with GPIOB0.
20
WLAN_WAKE_HOST WLAN Wakeup Host pin. This pin is also Shared with GPIOB1.
9. Supplier
Name of material Crystal Inductor Wifi chip
Capacitance Resistance PCB(12.2x13x0.8mm)
Supplier list Material brand
26MHz Sunlord/ CHILISIN/ SAMWHA/DDY
AIC SAMSUNG /EYANG/Murata
UniOhm /YAGEO A,O,I,F
RoHS
Page 9
WiFi Module
CDW-B1800DL 10. Physical photo
10.1 No IPEX Physical photo: CDW-B1800DL-00H
PIN1
H
10.1 IPEX Physical photo: CDW-B1800DL-10H
Page 10
WiFi Module
CDW-B1800DL
H
10.2 CDW-B1800DL-01H
PCB
Page 11
WiFi Module
CDW-B1800DL
11. Layout Recommendation
2.33 1.00 2.00
2.98 13mm
2.16
3.53
12.2mm
3.40
0.8 1.0
1.20
1
1.27
0.7
2.45
20 19 18 17 16 15
1.20 1.00 2.83
14
2
2.50
1.20 13
3 1.20
3.50
12
4
2.80
11
5 6 7 8 9 10
1.37
1.0
0.8
3.40
1.27
0.7
1.27
2.45
12. Warpage
(Top view)
0.1mm , gap0.1mm
13. Baking & storage temperature & Recommended Reflow Profile
13.1 Baking & storage temperature
A. Storage life12 months. Storage conditions:<40. Relative humidity:<90%R.H. (12<40<90%R.H.)
Page 12
WiFi Module
CDW-B1800DL
B. After this bag is opened , devices that will be subjected to infrared reflow, vapor-phase reflow, or equivalent processing must be .(SMT )
a. Check the humidity card :stored at 20%RH.If :30%~40%(pink)or greater than 40%(red).Labeling module has moisture absorption.( 30%30%~40%( 40%.)
b. Mounted within 168 hours at factory conditions of: t30%60%R.H. (30%60%R.H, 168)
c. Once opened, the workshop the preservation of life for168 hours. (168.)
C. Module apart packing after 168 hoursIf baking is required, devices may be baked for. (168)
a. Modules must be to remove module moisture problem. (.)
b. Baking temperature: 40±5, 120 hours. (40±5120).
c. After baking, put proper amount of desiccant to seal packages. ()
Page 13
13.2 Recommended Reflow Profile
Referred IPC/JEDEC standard. Peak Temperature : 250°C Number of Times : 2 times
217
Slope: 1~2/sec max. (217 to peak)
Prehe at: 150~200
WiFi Module
CDW-B1800DL
peak:
245
+0 -5
Ramp down rate: Max. 2.5/sec
25
60~ 120 sec
Ramp up rate: Max. 2/sec
14. Packing information
14.1 Carrier size Detail:
40~ 60 sec Time(sec)
Page 14
14.2 Packaging Detail:
24±2mm
WiFi Module
CDW-B1800DL
Vacuum packing
AL BAG ANTI-STATIC
Color of plastic disc: blue A roll of 2000pcs(20pcs)
inner box K3K: 33.5cm*34.7cm*7cm A box of 2000 PCS
carton K=A: 36.4*35.7*37.5cm A case of 10000 PCS
ESD CAUTION
The B1800DL series module is ESD (electrostatic discharge) sensitive device and may be damaged with ESD or spike voltage. Although B1800DL series module is with built-in ESD protection circuitry, please handle with care to avoid the permanent malfunction or the performance degradation.
Page 15
FCC WARNING FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
15.105 Information to the user. (b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. The final end product must be labelled in a visible area with the following:
“Contains Transmitter Module FCC ID:2BN5S-2503V
Requirement per KDB996369 D03
2.2 List of applicable FCC rules
List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.3
Explanation: This module meets the requirements of FCC part 15C(15.247).
2.3 Summarize the specific operational use conditions
Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain.
Explanation: The EUT contains a PCB antennas. Yes, this module includes a permanent additional antenna with a maximum antenna gain of 3.3dBi for 2.4G The prototype is used under mobile conditions.
2.4 Limited module procedures
If a modular transmitter is approved as a “limited module,” then the module manufacturer isresponsible for approving the host environment that the limited module is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions.
A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval.
This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured. For additional hosts other than the specific host originally granted with a limited
module, a Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. Explanation: The module is a single module.
2.5 Trace antenna designs
For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements.
a) Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna);
b) Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency, the wavelength, and antenna shape (traces in phase) can affect antenna gain and must be considered);
c) The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC) board layout;
d) Appropriate parts by manufacturer and specifications;
e) Test procedures for design verification; and
f) Production test procedures for ensuring compliance.
The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.
Explanation: No, The module has no tracking antenna design, is PCB antenna.
2.6 RF exposure considerations
It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1) to the host product manufacturer, to define the application conditions (mobile, portable xx cm from a person’s body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility of the module through a change in FCC ID (new application).
Explanation: This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.” This module is designed to comply with the FCC statement, FCC ID: 2BN5S-2503V
2.7 Antennas
A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
For situations where the host product manufacturer is responsible for an external connector, for example with an RF pin and antenna trace design, the integration instructions shall inform the installer that unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors.
Explanation: The EUT contains one PCB antennas. Yes, this module includes a permanent additional antenna with a maximum antenna gain of 3.3dBi for 2.4G.The prototype is used under mobile conditions.
2.8 Label and compliance information
Grantees are responsible for the continued compliance of their modules to the FCC rules. This
includes advising host product manufacturers that they need to provide a physical or elabel stating “Contains FCC ID” with their finished product. See Guidelines for Labeling and User Information for RF Devices KDB Publication 784748.
Explanation:The host system using this module, should have label in a visible area indicated the following texts: “Contains FCC ID: 2BN5S-2503V
2.9 Information on test modes and additional testing requirements5
Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide. Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product.
The grantee should provide information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host.
Grantees can increase the utility of their modular transmitters by providing special means, modes, or instructions that simulates or characterizes a connection by enabling a transmitter. This can greatly simplify a host manufacturer’s determination that a module as installed in a host complies with FCC requirements.
Explanation: Can increase the utility of our modular transmitters by providing instructions that simulates or characterizes a connection by enabling a transmitter.
2.10 Additional testing, Part 15 Subpart B disclaimer
The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules
that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15
Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Explanation: The host shoule be evaluated by the FCC Subpart B.
This product adopts PCB antennas. The maximum antenna gain is 3.3dBi for the 2.4G antenna
IC statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic DevelopmentCanada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term “IC: ” before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d’Innovation, Sciences etDéveloppement économique Canada. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pasproduire de brouillage,et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme auxCNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1)L’appareil ne doit pas produire de brouillage; 2)L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre lefonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then theoutside of the device into which the module is installed o display a label referring to the enclosed module. This exteriorlabel can use wording such as the following: “Contains IC: 33667-2503V” any similar wording that expresses the same meaningmay be used. l’appareil hôte doit porter une étiquette donnant le numéro de certification du module d’Industrie
Canada, précédé des mots «Contient un module d’émission », du mot « IC: 33667-2503V » ou d’une formulation similaireexprimant le même sens, comme suit The device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 andcompliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure andcompliance. Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 6.6 de RSS 102 etla conformité à l’expositionde RSS-102 rf, utilisateurs peut obtenir l’information canadienne surl’exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter. This equipment should be installed and operated with a minimum distance of 20centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ouémetteur. Cet équipementdevrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
Cet émetteur radio IC : 33667-2503V a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés ci-dessous, avec le gain maximal admissible indiqué. Les types d’antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil. The radio transmitter IC: 33667-2503V has been approved by The Ministry of Innovation, Science and Economic Development of Canada to use the following antenna types with the specified maximum allowed gain. Antenna types not included in this list, whose gain is higher than the maximum gain of any type listed, are strictly prohibited from use with this device.
Cet émetteur radio IC : 33667-2503V a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés ci-dessous, avec le gain maximal admissible indiqué. Les types d’antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil.
The radio transmitter IC: 33667-2503V has been approved by The Ministry of Innovation, Science and Economic Development of Canada to use the following antenna types with the specified maximum allowed gain. Antenna types not included in this list, whose gain is higher than the maximum gain of any type listed, are strictly prohibited from use with this device.
ANT1 Type of antenna: Antenna Gain: Impedance: Manufacture: Model:
PCB antenna 2.4G :2400-2500(3.3dBi) 50hm CHINA DRAGON TECHNOLOGY LIMITED SD18V1
Documents / Resources
 |
Cdtech CDW-B1800DL-01H WiFi Module [pdf] Owner's Manual CDW-B1800DL-01H, CDW-B1800DL-01H WiFi Module, WiFi Module, Module |