CASIO 5537 Adjusting Hand Alignment Module
Before Getting Started…
This section provides an overview of your watch and explains how to connect with a phone. While there is a connection with a phone, the watch time setting is adjusted automatically. You can also change the watch’s other settings.
Note
The illustrations included in this operation guide have been created to facilitate explanation. An illustration may differ somewhat from the item it represents.
Watch Face and Display Indicators
A Displayed while the watch is indicating
summer time.
B Displayed while an alarm is turned on. C Displayed while the hourly time signal is
enabled.
D Displayed while in the Recall Mode. E Displayed while the watch’s hands are
shifted for easier reading.
F Displayed while Auto Light is enabled.
G Displayed during p.m. times while 12-hour
L In the Timer Mode, the mode hand points
to [TR].
M In the Alarm Mode, the mode hand points
to [AL].
N In the World Time Mode, the mode hand
points to [WT].
O After you measure a lap time, the second
Cycling Between Timekeeping Mode Digital Display Contents
Each press of (A) in the Timekeeping Mode toggles between the display information as shown below.
Shifting the Hands
Hand shift moves the hands out of the way for easy viewing of display information.
- 1. While holding down (B), press (D).
● This will shift the analog hands to allow easy viewing of display information. - 2. To return the hands to their normal timekeeping positions, hold down (B) as you press (D) again, or press (D) to change to another mode.If you leave the watch with its hands shifted and do not perform any operation for about one hour, the hands will resume normal timekeeping automatically.
Solar Charging
This watch runs on power supplied from a rechargeable (secondary) battery that is charged by a solar panel. The solar panel is integrated into the face of the watch, and power is generated whenever the face is exposed to light. While you are wearing the watch, make sure that its face (solar panel) is not blocked from light by the sleeve of your clothing. Power generation efficiency is reduced even when the face of the watch is blocked only partially.
Power Saving Function
Leaving the watch in a dark location for about one hour between the hours of 10 p.m. and 6 a.m. will cause the display to go blank, and the watch to enter Level 1 power saving. If the watch is left in this condition for six or seven days, the watch will enter Level 2 power saving.
Power Saving Level 1 :
The second hand stops at 12 o’clock and the digital display goes blank to save power. The watch can connect with a phone at this level.
Power Saving Level 2 :
All hands stop and the digital display goes blank to save power. All functions are disabled.
Recovering from Power Saving Operation
Use one of the operations below to exit power saving.
Using Mobile Link with
a Mobile Phone
While there is a Bluetooth connection between the watch and phone, the watch time setting is adjusted automatically. You can also change the watch’s other settings.
Getting Ready
A Install the required app on your phone.
In Google Play or the App Store, search for the “CASIO WATCHES” phone app and install it on your phone.
B Configure Bluetooth settings.
Enable the phone’s Bluetooth.
● If the watch does not indicate the correct time even if is able to connect with a phone, adjust the hand and date indicator positions.
l Adjusting Hand Alignment
● If there is a World Time City specified with CASIO WATCHES, its time will also be adjusted automatically.
● The watch will connect with the phone and perform auto time correction at around 12:30 a.m., 6:30 a.m., 12:30
p. m. and 6:30 p.m. The connection is automatically terminated after auto time correction is complete.
● The watch cannot connect with a phone for time adjustment while a stopwatch measurement or timer operation is in progress.
● You can perform the above operation for time adjustment from any watch mode.
● The connection is terminated automatically after time adjustment is complete.
● If time adjustment fails for some reason, [ERR] will appear.
Configuring Stopwatch Settings
You can use the CASIO WATCHES phone app to configure the lap time measurement function settings shown below.
You can specify one of the target time types described below, which are used to calculate the difference between your target time and actual lap time measurements.
FASTEST :
Following start of a stopwatch elapsed time measurement session, the fastest measured lap time of the current session is automatically set as the target time. Resetting the stopwatch to all zeros will clear this target time.
TARGET :
You can use CASIO WATCHES to specify a desired target time.
LAST :
Following start of a stopwatch elapsed time measurement session, the last measured time of the current session is automatically set as the target time. Resetting the stopwatch to all zeros clear this target time.
1. Y Tap the “CASIO WATCHES” icon.
2. X Hold down (C) for at least 1.5 seconds until [CONNECT] starts to flash. When a connection is established between the watch and phone,
[CONNECT] will stop flashing and the second hand will move from [R] to e.
● If connection fails for some reason,[ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
2. X Hold down (C) for at least 1.5 seconds until [CONNECT] starts to flash. When a connection is established between the watch and phone,
[CONNECT] will stop flashing and the second hand will move from [R] to e.
● If connection fails for some reason,[ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
Documents / Resources
 |
CASIO 5537 Adjusting Hand Alignment Module [pdf] User Guide 5537, 5537 Adjusting Hand Alignment Module, 5537, Adjusting Hand Alignment Module, Hand Alignment Module, Alignment Module, Module |