1. Introducció
The HENDI Automatic Water Softener, Model 230459, is an advanced system designed for commercial use to effectively prevent limescale buildup in plumbing installations. This unit operates at 230V and 18W, ensuring efficient and reliable water treatment. By reducing mineral deposits, it helps extend the lifespan of your appliances and maintain optimal water flow.
Figura 1: Frontal view of the HENDI Automatic Water Softener, Model 230459.
2. Informació de seguretat
Aquest és un producte comercial no pensat per a ús domèstic.
Always adhere to local regulations and safety standards during installation, operation, and maintenance. Disconnect power before performing any service or maintenance. Ensure proper grounding to prevent electrical hazards. Keep the unit away from direct sunlight and extreme temperatures.
3. Característiques del producte
- Pressió de funcionament: 1.5 - 6.0 bar
- Temperatura ambient de funcionament: 5 – 38 °C
- Output for 10°dH: 1200 litres
- Tauler de control: Allows configuration of operating time, regeneration time, and treated water quantity.
- Bloqueig automàtic: Prevents unauthorized access to settings.
- Bloqueig per a nens: Special function to prevent accidental changes.
4. Configuració i instal·lació
The HENDI Automatic Water Softener is designed for installation on the main water line. It should be installed before the water line splits to the water heater or other plumbing fixtures to ensure all water entering the system is treated.
- Selecció d'ubicació: Choose a dry, level area with adequate space for installation and future access. Ensure the ambient temperature remains within 5 – 38 °C.
- Connexió al subministrament d'aigua: Connect the unit to the main water supply line. Ensure all connections are secure and leak-free.
- Connexió de drenatge: Connect the drain line according to local plumbing codes.
- Connexió elèctrica: Connect the unit to a grounded 230V electrical outlet.
- Inici inicial: Follow the operating instructions to initiate the first regeneration cycle and configure settings.
Note on Iron Content: If your source water has iron levels exceeding 0.3 ppm, it is recommended to use an iron removal filter before the water softener to ensure optimal performance and longevity of the unit.
5. Instruccions de funcionament
The unit features an intuitive control panel for managing its functions. Refer to the display and buttons for configuration.
Figure 2: Close-up of the control panel with display and buttons.
- Setting Operating Time: Use the control panel to set the desired operating schedule for the unit.
- Configuring Regeneration Time: Adjust the regeneration cycle frequency and duration based on your water hardness and usage.
- Adjusting Treated Water Quantity: Set the volume of water to be treated before a regeneration cycle is initiated.
- Bloqueig automàtic: The system includes an automatic lock feature to prevent unintended changes to the settings. Consult the on-screen prompts for activation/deactivation.
- Bloqueig per a nens: Activate the child lock function through the control panel to secure settings from accidental tamperrant.
6. Manteniment
The HENDI Automatic Water Softener Model 230459 is designed for minimal maintenance after initial setup. Regular checks are recommended to ensure optimal performance.
- Inspecció periòdica: Visually inspect the unit and connections for any signs of leaks or damage.
- Neteja: Keep the exterior of the unit clean and free from dust and debris. Use a soft, damp cloth for cleaning. Do not use abrasive cleaners.
- Nivell de sal: This unit operates using an ion exchange method, which typically requires salt for regeneration. Ensure the salt reservoir is adequately filled. Refer to the control panel for indicators and specific instructions on salt replenishment.
7. Solució De Problemes
If you encounter issues with your HENDI Automatic Water Softener, please refer to the following common troubleshooting steps:
| Problema | Causa possible | Solució |
|---|---|---|
| La unitat no s'encén | Sense font d'alimentació; connexió fluixa | Check power cable and outlet. Ensure unit is properly plugged in. |
| Water still hard | Incorrect settings; low salt level; high iron content; unit malfunction | Verify control panel settings. Check and refill salt reservoir. Test water for iron levels and consider a pre-filter if needed. Contact support if problem persists. |
| Missatge d'error a la pantalla | Internal fault; sensor issue | Note the error code and consult the full product manual or contact customer support. |
For issues not listed here, or if solutions do not resolve the problem, please contact HENDI customer support.
8. Especificacions
| Atribut | Detall |
|---|---|
| Fabricant | HENDI |
| Número de model | 230459 |
| Dimensions del producte | 56 x 42 x 24.5 cm (22 x 16.5 x 9.6 polzades) |
| Pes | 9.94 kg (21.9 lliures) |
| Voltage | 230 Volts |
| Consum d'energia | 18 watts |
| Pressió de funcionament | 1.5 - 6.0 bar |
| Temperatura ambient de funcionament | 5 – 38 °C |
| Caudal | 5 litres per minut |
| Capacity (10°dH) | 1200 litres |
| Material | Ceràmica |
| Mètode d'instal·lació | Autònom |
| Mètode de purificació | Ion Exchange |
| Característiques especials | Bloqueig infantil |
9. Informació de la garantia
HENDI products are manufactured to high-quality standards. For detailed warranty terms and conditions, please refer to the warranty card included with your product or visit the official HENDI weblloc web. Conserveu el comprovant de compra per a qualsevol reclamació de garantia.
10. Suport
For technical assistance, spare parts, or further inquiries regarding your HENDI Automatic Water Softener, please contact HENDI customer service. Contact details can be found on the HENDI weblloc web o a la documentació que s'inclou amb el producte.
HENDI Weblloc: www.hendi.eu
