BuzzTV E1-E2 Android Box Essentials with Remote
Connection
AV Connection
- Connect the AV cable of the 3 colors (red/white/yellow) to the STB’s AV output interface, and the other end to the TV’s AV input interface. The connection can be made by colour.
- Power on the STB. Set the TV video mode to AV input.
HDTV Connection
- Connect the HDMI cable to the STB output interface, and the other end to the TV’s HDMI input interface.
- Power on the STB. Set the TV video mode to HDTV input.
Troubleshooting
Warning:
Under no circumstances should you try to repair the STB by yourself, as this will invalidate the warranty. Do not open it as there is a risk of electrical shock. If any fault occurs, please first check with this troubleshooting checklist. If you are unable to remedy a problem by following this guide, contact your dealer for help.
|
Problem |
Solution |
| No Power | • Check if the power adapter is properly connected to the power and the TV box • Press the power on the remote controller to turn on the power |
| No Picture | • Re-Connect the HDTV cable or AV cable • Check if the TV is powered on |
| No sound or distorted sound | • Adjust the volume • Check that the speakers are connected correctly |
| The TV box does not respond to the remote control | • Aim the remote control directly at the sensor on the front of the TV box • Reduce the distance to the TV box • Replace batteries in the remote control • Possibility of a system crash, disconnect and reconnect the power supply |
| No sound during playback | • The audio codec may not be supported by the TV box • Check the volume |
| The contents of the USB or flash drive cannot be read | • The USB or flash drive format is not compatible with the box • If one of the USBs can not be read, please turn o the TV box for 30 seconds and restart the TV box |
| Slow operation of the USB flash drive | • Large file size or high-resolution USB flash drive takes longer time to read and display on the TV screen |
| The TV screen is blank and the player LED is blinking | • Turn o the TV box, wait 30 seconds, and turn it on again • Check if the HDTV connection is correct or try changing the HDTV cable |
Remote + Button List
Learning Remote Feature
Learning methods please see below:
- Press and hold “Power”+”OK” for more than 3 seconds, and the LED will be turned on, indicating the remote has entered learning mode.
- Align the IR tube of the remote control with the IR tube of the remote control which needs to be learned within 3cm.
- Press the “TV Power” button on the remote control, the LED will change from long light to slow flashing, waiting to receive the learning signal. Press the button of the remote control which needs to be learned and keep it sending the IR code. When the remote controller receives the learning signal, the LED flashes 3 times and then long light, indicating that the learning signal is received.
- Repeat step c to learn the “Source” key.
- Press the”OK” key, then the LED is turned off, indicating the code has been saved, and exit the learning mode.
Lights & Indicators
Status Lighting on the Front of STB indicates the following:
- Blue – ON
- Red – OFF
Warranty Information
For warranty information and registration, please visit www.buzztv.com/register.
support
www.buzztv.com/support. cs@buzztv.com.
Documents / Resources
 | E1-E2 Android Box Essentials with Remote |
References
- buzztv.com/registerwww.buzztv.com
- buzztv.com/supportwww.buzztv.com
- User Manualmanual.tools
Published: March 14, 2023
My Buzz box E2 Essential when powered on the B icon comes on and disappears after few seconds comes on again and disappears. It doesn’t proceed any further. What is the solution?
Why is my BuzzTV E2 Essential stuck in a boot loop where the logo appears and disappears repeatedly?
The issue you are describing, where the BuzzTV logo (the "B" icon) appears and disappears repeatedly, is known as a boot loop. This often indicates a power supply issue or a system crash. Based on the troubleshooting guide for the BuzzTV E1/E2 series, please try the following steps:
If these steps do not resolve the issue, you can contact BuzzTV technical support at 1-866-928-9988 or email cs@buzztv.com.
Read the full Q&A page