BuzzTV BT-350 Remote User Guide

The learning function on the BT-350 remote allows you to control your TV. Follow these steps:
Press and hold the TV POWER + TV SOURCE buttons on the BT-350 for 3 seconds.

Release the buttons when the blue light turns on.
Pairing the BT-350 remote with your BuzzTV device via Bluetooth:
Navigate to Settings > Remotes & Accessories > toggle Bluetooth to ON on your BuzzTV device.

Press and hold the VOL – & OK Button on the BT-350 for 3 seconds until the red light flashes.
Select BuzzTV BT-350 on your BuzzTV Device to complete the pairing.

Verify the pairing by checking for BuzzTV BT-350 under the Remotes and Accessories Menu.
Activate voice control on supported models by pressing the microphone button and speaking a command.

Press and hold the blue button for 3 seconds.
The red LED will blink twice to indicate the change in backlight status.

BT-350 Remote

Learning Function

BT-350 Remote – Learning Function

The learning function on the BT-350 remote is used to control your TV. You will be able to control: Power ON/OFF, Volume and Input Source. To do this you will need the factory remote control for your TV.

On the BT-350, press and hold the TV POWER + TV SOURCE for 3 seconds. Once the blue light turns on, release the buttons.
Press the learning key you would like to program (TV POWER/SOURCE/ TV VOL+/ TV VOL-) and the blue light will start ﬂashing. The ﬂashing blue light indicates the BT-350 is in learning mode.

Align your TV Remote and the BT-350 so that the front transmitters are pointing at each other. They should be within 1 inch or 3 cm of each other.
Press the button that you want to learn on the original remote. After receiving a learning function successfully, the red light on the BT-350 will blink 4 times.

To learn other keys, repeat Steps 2-4
After entering the learning mode, you can exit the learning mode by short-pressing the “TV POWER + TV SOURCE” keys.
To clear the learning function memory Long press the “OK+Back” buttons for 3 seconds The red light ﬂashes 3 times to clear the learning data

Bluetooth Pairing

On your BuzzTV device, navigate to Settings > Remotes & Accessories > toggle Bluetooth to ON. Then choose: Add Accessory
On the BT-350, press and hold the VOL – & the OKButton for 3 seconds. Once the red light starts flashing, release the buttons

Select “BuzzTV BT-350” on your BuzzTV Device
You are now Bluetooth-paired. You can confirm this by looking for “BuzzTV BT-350” under the Remotes and Accessories Menu

Note:
If you do not select the key within 15 seconds after entering the learning state, it will automatically exit the learning state.

Please note not all TVs are compatible with source pairing

CEC settings to support the BT-350, your TV & your BuzzTV Box If you were successful in TV source pairing the BT-350 to your TV then you need to make sure the CEC settings on both the TV and your\ BuzzTV Box are enabled and in some cases in the correct HDMI port on the TV, refer to your TV manual if needed. (Initially set to ON)

Voice Control

To use Voice control press the microphone button & say a command
Only supported on certain models*

Backlight

To turn on or off the backlight press and hold the blue button for 3 seconds , the red LED will blink twice

Warranty Information

For warranty information and registration, please visit: www.buzztv.com/register

CONTACT

FAQ

Q: What should I do if my TV is not compatible with source pairing CEC settings for the BT-350?
A: If your TV is not compatible, ensure that CEC settings are enabled on both your TV and BuzzTV Box. Refer to your TV manual for guidance on setting up CEC functionality.

Documents / Resources

BuzzTV BT-350 Remote [pdf] User Guide
BT-350, BT-350 Remote, BT-350, Remote

References

User Manual

BuzzTV BT-350 Remote

Product Specifications

Product Usage Instructions