BUILTBRIGHT BB6110A Work Bar Strobe 4 Slim
SPECIFICATIONS
- Input Voltage: 12-24VDC
- Operating Current: 0.96A @ 12VDC
- Operating Temperature: -40° to 149°F (-40° to 65°C)
INCLUDED
- 1x LED light bar
- 1x Mounting Bezel
- 1x 3M VHB tape
- 1x Mounting Gasket
- Mounting hardware
INSTALLATION
- Mount to a flat surface or one with minimal curvature.
- Mark drill hole locations on the mounting surface using the gasket or VHB tape as a template.
- Drill a 25/32” (20mm) hole for the wires protruding from the rear of the unit at the correct location. Deburr any sharp edges from this hole.
- Mount the light along with the mounting gasket. Use the self -tapping screws provided to secure the light. Cover with mounting bezel.
WIRING
Black – To chassis ground
White – To +VDC and memory function 1 (fuse @ 2A)
Gray – To +VDC and memory function 2 (fuse @ 2A)
Red – To +VDC and memory function 3 (fuse @ 2A)
Yellow – Pattern selection
- Apply YELLOW wire to +VDC:
- Less than 1 second for next pattern
- 2-4 seconds for previous pattern
- 7+ seconds for steady burn
- Synchronization: After setting each light at the right pattern, connect yellow wires of all light heads together.
- Phase Operation: Phase 1 flashes simultaneously with Phase 1, Phase 2 flashes simultaneously with Phase 2, Phase 1 alternates with Phase 2 (Up to 8 units can be synchronized.)
TABLE
|
FLASH PATTERNS |
|
| 1 | Single Flash,ECE R65 Phase 1* |
| 2 | Single Flash, California Title 13 Phase 1* |
| 3 | Double Flash Phase |
| 4 | Triple Flash Phase 1* |
| 5 | Single Flash,ECE R65 Phase 2 |
| 6 | Single Flash, California Title 13 Phase 2 |
| 7 | 7 Double Flash Phase 2 |
| 8 | 8 Triple Flash Phase 2 |
| 9 | Quadruple Flash Phase 1 |
| 10 | 0 Quadruple Flash Phase 2 |
| 11 | Quintuple Flash Phase 1 |
| 12 | Quintuple Flash Phase 2 |
| 13 | Combination Single/Double Flash Phase 1 |
| 14 | Combination Single/Double Flash Phase 2 |
| 15 | Combination Single/Triple Flash Phase 1 |
| 16 | Combination Single/Triple Flash Phase 2 |
| 17 | Combination Single/Quintuple Flash Phase 1 |
| 18 | Combination Single/Quintuple Flash Phase 2 |
| 19 | Single Flash Left/Right Split |
| 20 | Strobe |
| 21 | Cruise(20%) |
| 22 | Steady Burn |
WARRANTY
ARC Lighting provides a 5 year warranty against manufacturing defects from date of purchase. If warranty service is needed, please contact the authorized dealer of where your product(s) were originally purchased.
WARNING: CANCER AND REPRODUCTIVE HARM WWW.P65WARNINGS.CA.GOV
CUSTOMER SUPPORT
Phone: 888-608-2220
Email: support@arc.lighting
Website: www.arc.lighting/warranty-claim
BASTROP, TEXAS 78602
UNITED STATES OF AMERICA
WWW.BUILT-BRIGHT.COM
Documents / Resources
 |
BUILTBRIGHT BB6110A Work Bar Strobe 4 Slim [pdf] Installation Guide BB6110A Work Bar Strobe 4 Slim, BB6110A, Work Bar Strobe 4 Slim, Bar Strobe 4 Slim, Strobe 4 Slim, 4 Slim |