B06056-01 BT Profile 6C20 Engine
“
Specifications:
- Model: BT-PROFILE 6C20
- Version: 1.0
- Indoor Use Only
- Minimum Distance from Lighted Objects: More than 1 meter
Product Usage Instructions:
Safety Instructions:
Ensure indoor use only. Read all instructions before use.
Maintain a minimum distance of more than 1 meter between the light
output and any illuminated surface. Avoid staring directly at the
operating lamp to prevent harm to the eyes. Never look directly
into the light source and avoid using the effect around individuals
with epilepsy.
Overhead Rigging Setup:
Use the setup menu to configure the projector fully. Settings
are saved even when disconnected from power.
- [MENU] button: Press to enter/leave setup menu.
- [ENTER] button: Press to select/confirm or store current menu
option or value. - [UP/DOWN] button: Navigate setup menu or change a value.
Operation Modes:
The projector offers different operation levels and modes as
follows:
- Level 0 – Static: Set address and run
mode. - Level 1 – Color Settings: Adjust Red, Green,
Blue, Amber, Lime, Cyan, Strobe, and Dimmer settings. - Level 2 – Detailed Settings: Fine-tune color
values and other parameters.
Program Editing and Settings:
Select automatic programs or customize settings as needed.
- Edit custom programs with fade transitions and scene editing
capabilities. - Upload custom programs, restore factory settings, and adjust
dimming curves. - Set PWM frequency, fan rotation modes, and display
preferences.
Frequently Asked Questions (FAQ):
Q: Can I use this product outdoors?
A: No, this product is designed for indoor use only.
Q: How do I adjust the color settings?
A: Use the setup menu to navigate to the color settings section
and adjust the Red, Green, Blue, Amber, Lime, and Cyan values as
needed.
Q: What should I do if the lamp is too bright?
A: Ensure a minimum distance of more than 1 meter between the
light output and any illuminated surface to reduce brightness.
“`
ENGLISH
OPERATION MANUAL V1.0
OPERATION MANUAL
Thank you for buying this Briteq® product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
· This LED profile spotlight features powerful 280W multi-color LED technology. · It is a perfect replacement for energy consuming 2kW halogen lamps in theaters! · The 6-color RGBALC LED cluster (red, green, blue, amber, lime, cyan) guarantees:
· Perfect white presets between 1800K and 10000K with high CRI >90Ra · Rich color selection with the same color presets as in the BT-THEATRE HD2 and BT-PROFILE HD · Very realistic amber drift (dim-to-warm) emulation of traditional halogen lamps · Color calibration system makes color differences between different batches a thing of the past · Very quiet operation with low-noise cooling fan and different fan presets (live, studio, power) · Can be used in standalone mode, without any DMX control · DMX-controlled: 8 different channel modes for maximum flexibility · RDM functionality for easy remote installation · Flicker-free TV shooting thanks to adjustable high speed LED refresh rate · Fast and slow dimmer response · OLED display for easy navigation through the setup menu · Lock function to prevent unwanted change of settings · 5-pin DXM in/outputs + PowerCON TRUE1 compatible in/outputs for easy daisy-chaining.
Multiple optics available (ETC source four compatible): · BT-PROFILE 1530 OPTIC (15°-30° zoom range) · BT-PROFILE 2550 OPTIC (25°-50° zoom range) · Fixed aperture optics on special order only
The optional optics have: · Specially coated optics for sharply defined projections · Four profile blades specially coated for minimal reflections · Lockable compartment for use of the optionally available:
· GOBO Holder · IRIS (recommended for best projection results) · Optical cylinder can be rotated and locked in any position
BEFORE USE
· Before you start using this unit, please check if there’s no transportation damage. Should there be any, do not use the device and consult your dealer first.
· Important: This device left our factory in perfect condition and well packaged. It is necessary for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual.
· Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents: Check that the carton contains the following items: · BT-PROFILE 6C20 ENGINE · Power cable · Safety cable · English operating instructions, other languages can be downloaded from our website.
BRITEQ®
1/10
BT-PROFILE 6C20
ENGLISH
OPERATION MANUAL V1.0
SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only. The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance between light-output and the illuminated surface must be more than 1 meters
CAUTION: Do not stare at operating lamp. May be harmful to the eyes.
· To protect the environment, please try to recycle the packing material as much as possible. · To prevent fire or shock hazard, do not expose this appliance to rain or moisture. · To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages. · This unit is for indoor use only. · Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object enters the unit, immediately disconnect the mains power. · Locate the fixture in a well-ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls. · Don’t cover any ventilation openings as this may result in overheating. · Prevent use in dusty environments and clean the unit regularly. · Keep the unit away from children. · Inexperienced persons should not operate this device. · Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures. · Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. · Allow the device about 10 minutes to cool down before to start servicing. · Always unplug the unit when it is not used for a longer time or before to start servicing. · The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. · Check that the available voltage is not higher than the one stated on the unit. · The power cord should always be in perfect condition. Switch the unit immediately off when the power cord is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. · Never let the power-cord come into contact with other cables! · This fixture must be earthed in order to comply with safety regulations. · Don’t connect the unit to any dimmer pack. · Always use an appropriate and certified safety cable when installing the unit. · In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user serviceable parts inside. · Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same type and electrical specifications! · In the event of serious operating problems, stop using the fixture and contact your dealer immediately. · The housing and the lenses must be replaced if they are visibly damaged. · Please use the original packing when the device is to be transported. · Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy.
BRITEQ®
2/10
BT-PROFILE 6C20
ENGLISH
OPERATION MANUAL V1.0
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Overhead rigging requires extensive experience! Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. · Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing. · Locate the fixture in a well-ventilated spot, far away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls. · The device should be installed out of reach of people and outside areas
where persons may walk by or be seated. · Before rigging make sure that the installation area can hold a minimum
point load of 10times the device’s weight. · Always use a certified safety cable that can hold 12times the weight of
the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. · The device should be well fixed; a free-swinging mounting is dangerous and may not be considered! · Don’t cover any ventilation openings as this may result in overheating. · The operator has to make sure that the safety-relating and machinetechnical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal.
SETUP MENU / HOW TO SETUP
With the setup menu you can fully configure the projector. All settings are preserved when the unit is disconnected from the mains. [MENU] button: press to enter / leave the setup menu. [ENTER] button: press to select / confirm or store the current menu option or value. / [UP/DOWN] button: press to navigate the setup menu or change a value. All passwords of this product are <UP>, <DOWN>,<UP>, <DOWN>, <ENTER>)
Level 0
Static
Address Run mode
Level 1 Red Green Blue Amber Lime Cyan Strobe Dimmer
CCT Pre
Col Pre
001-512 DMX Static
Slave
Level 2 0-255 0-255 0-255 0-255 0-255 0-255 0-25 0-255
None – 10000K
None – Col48
Remarks
Combine [RED][GREEN][BLUE][LIME][AMBER][CYAN] to create an infinite range of colors (0-255). PS: Color
settings are not used when a CCT or COLOR PRESET is selected.
Set the value of the [STROBE](0-25Hz). Master dimmer of all static colors and presets The different CCT values can be selected in static mode. Choose “NONE” if you want to use the separate color settings or color presets. The 48 color presets can be selected in static mode. Choose “NONE” if you want to use the separate color settings or CCT-presets. Set the DMX ADDRESS [DMX] Using the DMX 512 controller to control [SLAVE] Master/Slave operation. [STATIC] use the settings from the STATIC menu.
UNO
Personality
DOS
Use the menu to select desired channel mode
BRITEQ®
3/10
BT-PROFILE 6C20
ENGLISH
Basic SSP Tour TR16 HSIC CMY Auto 1 …
Auto 10
Auto Program Pr.01
Pr.02
Edit Setting Info
Program01 Program02 Upload Reset Dimmer
Dimming curves
Tungsten fade DMX error
PWM rate
Perform Disp key
Disp Time
Fixture Hours Version RDM
Dim4 Off Linear Square Inv. SQ Law S-curve On / Off Save Black 1200Hz 2400Hz 4000Hz 6000Hz 25000Hz Live Power Studio
On/Off
On 10s 30s 2min
UID Label
OPERATION MANUAL V1.0
Selects automatic AUTO program and AUTO program speed. Programs [CUSTOM 1] to [CUSTOM 2] are fully pre-programmed and can be edited in [EDIT] mode.
Enter the [EDIT] mode to edit the custom programs [PROGRAM01] to [PROGRAM2]. Each custom program has 30 scenes that can be edited. Fade transition time, time 0-255 unit is second, fade time setting should be less than time setting. After editing the program, Play in AUTO.
Select [UPLOAD] to upload the custom programs Restore factory settings Dimming curves Off (fast) and DIM4 (slow)
Enables/disables the tungsten emulation Hold after loss of DMX signal Blackout after loss of DMX signal
Sets the PWM frequency
Automatic rotation of fan Fast rotation of fanall power Fan mode low speed Locks display (passcode is : <UP>, <DOWN >, <UP>, <DOWN>, <ENTER>) Display backlight always on Turns off display backlight after: 10s/30s/2min of inactivity
Hours of fixture use Software versions Check fixture’s ID Check fixture’s LABEL
BRITEQ®
4/10
BT-PROFILE 6C20
ENGLISH
OPERATION MANUAL V1.0
ELECTRICAL INSTALLATION
Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.
Electrical installation for two or more units in DMX-mode: · The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units. · Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) · To prevent strange behavior of the light effects, due to interferences, you must use a
90 to 120 terminator at the end of the chain. Never use Y-splitter cables, this simply won’t work! · Make sure that all units are connected to the mains. · Each unit in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode.
USE IN STAND-ALONE (STATIC) MODE
· In the setup menu: select [RUN MODE] and choose the option [STATIC] · Now you can set the desired output manually:
· Set any desired color: combine the settings of the different separate colors · Set one of the color presets: choose [COL PRESETS] and select one of the 48 presets · Set one of the CCT presets: choose [CCT PRESETS] and select one of the CCT-presets · Choose the option [DIMMER] and set the desired light output. Remark: if you don’t use the preset options, both should be set to “NONE” to select any desired color.
RDM FUNCTIONS / REMOTE SETUP
RDM means “Remote Device Management”. This projector works with a brief set of RDM-functions which
means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of
these functions are briefly explained below, others will be added in the future.
· The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique
device ID.
· The DMX-controller asks each RDM device for some basic data so it knows which devices are connected.
The projector will respond:
· Device name:
BT-PROFILE 6C20
· Manufacturer:
Briteq®
· Category:
LED Dimmer
· Firmware: x.x.x.x
(firmware version of the projector)
· DMX address: xxx
(current DMX start address of the projector)
· DMX footprint: xx
(number of DMX-channels used by the projector)
· Personality: xx
(current personality [or DMX-working mode] used by the projectors)
· Temperature: xx°C Temperature of the LED engine
· The DMX-controller can send certain commands to each RDM device which allow remote setup of the units.
Thanks to this the projector can be setup remotely.
The following functions can be managed remotely: No more need to take a ladder and set all units one by one!
· DMX START ADDRESS: The start address can be set remotely from 001 to xxx. · PERSONALITY: The DMX working mode (DMX-chart) can be set remotely. These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMX-controller and send these data to all projectors at once. More functions will be added later.
BRITEQ®
5/10
BT-PROFILE 6C20
ENGLISH
OPERATION MANUAL V1.0
DMX CHARTS
UNO 1 –
DOS 1 2
Function Value Dimmer 000-255 Dimmer fine 000-255
HSIC 1 2 3 4 –
5
6
–
CMY 1 2 3 4
Basic 1 –
5
2
6
3
7
4
8
–
SSP 1 2 3 4 5 6 7 –
–
–
–
Tour 1 2 3 4 5 6 7 8
9
10
11
TR16 Function Value
–
Intensity 000-255
–
Hue
000-255
–
Hue fine 000-255
–
Saturation 000-255
1
Dimmer 000-255
2 Dimmer fine 000-255
3
Red
000-255
4
Red fine 000-255
5
Green 000-255
6
Green fine 000-255
7
Blue
000-255
8
Blue fine 000-255
9
Amber 000-255
10 Amber fine 000-255
11
Lime
000-255
12
Lime fine 000-255
13
Cyan
000-255
14
Cyan fine 000-255
–
Magenta 000-255
–
Yellow 000-255
15
Color presets
000-010 Disabled 011-255 Color presets
000-009 Disabled
010 1800K
025 2200K
040 2700K
055 3000K
070 3200K
085 4000K
16
CCT
100 4500K 115 5000K
130 5600K
145 6000K
160 6500K
175 7000K
190 8000K
205 10000K
255 10000K
000-016 Disabled
017-116 Magenta 99% <> 1%
17 Tint correction 117-139 Neutral (no effect)
140-239 Green 1% <> 99%
240-255 Green 100%
18
Auto
000-040 Disabled
BRITEQ®
6/10
BT-PROFILE 6C20
ENGLISH
–
9
–
7
10
–
8
11
–
OPERATION MANUAL V1.0
041-050 Auto 1
051-060 Auto 2
061-070 Auto 3
071-080 Auto 4
081-090 Auto 5
091-100 Auto 6
101-110 Auto 7
111-120 Auto 8
121-130 Auto 9
131-140 Auto 10
141-150 Custom 1
151-160 Custom 2
161-255 No function
–
12 19 Auto speed 000-255
000-009 Open
010-099 Strobe (0-25Hz)
8
13 20
Strobe
100-109 Open 110-179 Lightning strobe
018-189 Open
190-255 Random strobe
000-010 No function
011-015 Tungsten fade On (0s delay)
016-020 Tungsten fade off (0s delay)
021-100 No function
101-110 Dimmer off (3s delay)
111-120 Dimmer Dim4 (3s delay)
–
14 21
Control
121-150 No function 151-160 PWM: 1200Hz (3s delay)
161-170 PWM: 2400Hz (3s delay)
171-180 PWM: 4000Hz (3s delay)
181-190 PWM: 6000Hz (3s delay)
191-200 PWM: 25000Hz (3s delay)
201-210 All reset (3s delay)
211-255 No function
MAINTENANCE
· Make sure the area below the installation place is free from unwanted persons during servicing. · Switch off the unit, unplug the mains cable and wait until the unit has been cooled down. During inspection the following points should be checked: · All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded. · Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation. · When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. · The mains cables must be in impeccable condition and should be replaced immediately when even a small
problem is detected. · In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly. · The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
BRITEQ®
7/10
BT-PROFILE 6C20
ENGLISH
OPERATION MANUAL V1.0
· The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. · Clean with a soft cloth using normal glass cleaning products.
· Always dry the parts carefully. Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and national guidelines. Conformity has been established and the relevant statements and documents have been deposited by the manufacturer.
Mains Input: Fuse: Power consumption (max): Power connections: Power Linking capacity: DMX connections: Lamp: CRI: IP-Rating: Operating Temperature: Size: Weight (LED engine):
AC 100 – 240V, 50/60Hz T6.3A / 250V (20x5mm) 290 Watts PowerCON TRUE1 compatible connector, input / output 6A @ 240V 5 pin-XLR male / female inputs + outputs RGBALC LED 280W >90 IP20 0°C 45°C See drawing 6,54 kg
DIMENSIONS:
BRITEQ®
8/10
BT-PROFILE 6C20
ENGLISH
LUX CHARTS 25° – 50° lens + Iris
OPERATION MANUAL V1.0
15°-30° lens + Iris
BRITEQ®
9/10
BT-PROFILE 6C20
ENGLISH
OPERATION MANUAL V1.0
ANNEX 1 COLOR PRESETS + LEE / ROSCO FILTER NAMES + CIE 1931 X/Y coordinates
PRESET
COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 COLOR 14 COLOR 15 COLOR 16 COLOR 17 COLOR 18 COLOR 19 COLOR 20 COLOR 21 COLOR 22 COLOR 23 COLOR 24 COLOR 25 COLOR 26 COLOR 27 COLOR 28 COLOR 29 COLOR 30 COLOR 31 COLOR 32 COLOR 33 COLOR 34 COLOR 35 COLOR 36 COLOR 37 COLOR 38 COLOR 39 COLOR 40 COLOR 41 COLOR 42 COLOR 43 COLOR 44 COLOR 45 COLOR 46 COLOR 47 COLOR 48
VALUE
000-010 011-015 016-020 021-025 026-030 031-035 036-040 041-045 046-050 051-055 056-060 061-065 066-070 071-075 076-080 081-085 086-090 091-095 096-100 101-105 106-110 111-115 116-120 121-125 126-130 131-135 136-140 141-145 146-150 151-155 156-160 161-165 166-170 171-175 176-180 181-185 186-190 191-195 196-200 201-205 206-210 211-215 216-220 221-225 226-230 231-235 236-240 241-245 246-250 251-255
COLOR NAME
NO FUNCTION
L176
Loving Amber
R40
Light Salmon
L24
Scarlet
L164
Flame Red
L747
Easy White
R303
Warm Peach
L08
Dark Salmon
L25
Sunset Red
L04
Medium Bastard Amber
L237
C.I.D. (To Tungsten)
R321
Soft Golden Amber
L652
Urban Sodium
L212
L.C.T. Yellow (Y1)
L765
LEE Yellow
L513
Ice and a Slice
L100
Spring Yellow
L244
LEE Plus Green
R4430
Cal Color 30 Green
L122
Fern Green
L90
Dark Yellow Green
L243
LEE Fluorescent 3600K
R92
Turquoise
R94
Kelly Green
L327
Forest Green
L191
Cosmetic Aqua Blue
L728
Steel Green
L117
Steel Blue
L354
Special Steel Blue
L53
Paler Lavender
L501
New Color Blue
L174
Dark Steel Blue
L165
Daylight Blue
L136
Pale Lavender
L194
Surprise Pink
L142
Pale Violet
L700
Perfect Lavender
L35
Light Pink
L794
Pretty ‘n Pink
L328
Follies Pink
L795
Magical Magenta
L154
Pale Rose
L127
Smokey Pink
L192
Flesh Pink
L332
Special Rose Pink
L790
Moroccan Pink
L157
Pink
R332
Cherry Rose
L128
Cool LED Bright Pink
NO FUNCTION
X
0.407 0.499 0.561 0.659 0.389 0.448 0.498 0.566 0.370 0.430 0.477 0.535 0.340 0.389 0.380 0.410 0.324 0.318 0.234 0.184 0.286 0.235 0.185 0.162 0.300 0.256 0.223 0.173 0.284 0.246 0.204 0.159 0.288 0.240 0.209 0.177 0.335 0.335 0.335 0.327 0.350 0.397 0.410 0.465 0.378 0.457 0.489 0.570
Y
0.321 0.321 0.296 0.302 0.344 0.353 0.347 0.359 0.335 0.365 0.406 0.399 0.363 0.412 0.447 0.502 0.388 0.440 0.543 0.641 0.370 0.360 0.459 0.496 0.318 0.302 0.278 0.265 0.284 0.249 0.205 0.158 0.254 0.183 0.148 0.070 0.289 0.251 0.180 0.138 0.318 0.265 0.237 0.193 0.324 0.272 0.295 0.263
The information might be modified without prior notice You can download the latest version of this user manual on our website: www.briteq-lighting.com
BRITEQ®
10/10
BT-PROFILE 6C20
MAILING LIST
EN: Subscribe today to our mailing list for the latest product news! FR: Inscrivez-vous à notre liste de distribution si vous souhaitez suivre l’actualité de nos produits!
NL: Abonneer je vandaag nog op onze mailinglijst en ontvang ons laatste product nieuws! DE: Abonnieren Sie unseren Newsletter und erhalten Sie aktuelle Produktinformationen!
ES: Suscríbete hoy a nuestra lista de correo para recibir las últimas noticias! PT: Inscreva-se hoje na nossa mailing list para estar a par das últimas notícias!
WWW.BRITEQ-LIGHTING.COM
Copyright © 2024 by BEGLEC NV
`t Hofveld 2C ~ B1702 Groot-Bijgaarden ~ Belgium Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.
Documents / Resources
 |
BT-PROFILE B06056-01 BT Profile 6C20 Engine [pdf] Instruction Manual B06056-01, B06056-01 BT Profile 6C20 Engine, B06056-01, BT Profile 6C20 Engine, Profile 6C20 Engine, 6C20 Engine |