BSP S13E Switch Controller User Manual

S13E Switch controller manual

Schematic diagram of functional buttons

Applicable instructions

1. This product adopts ergonomic design, providing a comfortable grip;
2. Support Switch game consoles, PC computers, and mobile phones:
3. Support four modes of motor vibration intensity adjustment;
4. Support Turbo combination and automatic combination functions;
5. Supports wired connection, 2.4G connection, and Bluetooth connection;
6. Equipped with six axis motion sensing function, supporting strong motion sensing opening
   Due to system issues with the mobile phone, some phones may not support this device
   Due to uncontrollable factors such as official game platform software upgrades or source code changes, some games may not be able to connect and operate with this product. Our company is not responsible for any consequences. Our company reserves the right of final interpretation regarding this matter.

Product characteristic parameters

1. Working voltage: DC3.7V
2. Working current: about 120mA
3. Continuous usage time: 12 hours
4. Sleep current:<2ua
5. Charging voltage/current: DC5V/600mA
6. Standby time: 60 days of fully charged storage

Product Instructions

【SWITCH host connection】

1. On the SWITCH host, select Controller> Change Grip/Order to enter SWITCH host pairing mode interface Press L+R on the controller,
2. Press and hold the “ZR” button, then press “HOME” for 2 seconds. The indicator light will flash to connect. After successful connection, the channel light will remain on
3. When connecting the Switch again, press the “HOME” button to turn it on and it will automatically connect

[Wired mode connection]
Insert the USB data cable into the USB port of the computer host, and plug the Type-C port on the other end into the controller. If the channel light stays on after a successful connection, it indicates a successful connection;
Steam end: In the upper left corner of the Steam interface, select Settings – General Controller – Find Universal Controller, etc Switch host wired connection with indicator light constantly on
(in computer mode, wired recognition is X-in put, and Switch host recognition is wired Switch)

[PC 2.4G computer receiver mode]

1. Press and hold the “L” button, then press “HOME” for 2 seconds to enter the computer receiver mode. The indicator light on the controller will flash, indicating PC connection mode. The computer receiver will be plugged into the computer. After successful connection, the indicator light remains on;
2. Successfully connected, you can directly press the “HOME” button to automatically reconnect.

[Bluetooth X-input mode]

1. Press and hold the “R” button, then press “HOME” for 2 seconds to enter X-input mode. The controller indicator light will flash. Use the device to find and add a Bluetooth device, click search, find the
2. “Xbox Wireless Controller” device name, and select connect. After successful connection, the indicator light remains on; Successfully connected, you can directly press the “HOME” button to automatically reconnect.

Charging instructions

The battery level of the controller is low, and the indicator light is flashing;
When charging the controller, the indicator light flashes slowly;
When the controller is fully charged, the Indicator light turns off

Motor vibration intensity adjustment

Pressing and holding the TURBO+right joystick up and down can enhance and reduce the vibration of the motor

Axis calibration function

Place the handle flat on the desktop, Press and hold the “+”+”HOME” keys, keep the indicator light on, then release it. After calibration is complete, the indicator light will turn off.

ABXY Swap

When using Xinput and 2.4G modes, the ABXY function keys automatically convert to face shell characters. To switch to technical key characters, please hold down (B+X+HOME) at the same time to switch

TURBO settings

Press’ A ‘and then’ TURBO’, Then it is the “A” key Turbo combo
Press “A” for the second time and then press “TURBO”, Then the “A” key will automatically send consecutive messages
Press “A” for the third time and then press “TURBO”, Then press the ‘A’ key to turn off the continuous transmission (restore the original state)
When the “A” key is in AUTO automatic continuous firing mode, hold down the “TURBO-left joystick up and down” button to set the speed of automatic continuous firing, which is 15 strokes per second, 25 strokes per second, and 8 strokes per second. (Note: The method for setting other function keys is the same as above)

Macro programming

[Back macro extension settings]
Press and hold the “C” button on the controller, then press “GR”. After 1 second, the indicator light will flash rapidly. This is the setting mode
The GL setting method is the same as above
After the setting mode is turned on, the indicator light will flash, and at this time, the buttons can be set. The key pressed on the controller will be recorded on the GR button. For example, press the A key once, and A will be entered into the GR
[This key is for listing: other key positions can also be entered]
If multiple buttons need to be set: press A once, then press B, then press X, and then press Y, so that the order of GR moves is ABXY [This button is set to list: other move orders can be set to 12 ABXY/up, down, left, right/L/ZL/R/ZR]
After pressing the button, press GR again to complete the programming, and the indicator light will remain on.
[Back macro clear button]
Simultaneously press and hold the “C” and “GR” keys on the controller to enter programming mode. The indicator light will flash. Do not enter any key values at this time. Press the “GR” key again to eliminate the key values set before the GR key