BSJ Technology HW-PET10 Wireless Bluetooth Pet Locator Device
Device Installation
Device Inspection
Ensure the device is in good condition and all relevant accessories are included.
SIM Card Installation
Insert the SIM card into the designated slot with care, avoiding excessive force. Never insert or remove the SIM card while the device is powered on. Ensure the SIM card is capable of accessing the internet.
Optimal Terminal Placement
- A. Waterproofing: Choose a dry location that is less prone to water exposure, and keep the device away from air conditioning vents to prevent internal condensation, which can significantly impact its lifespan.
- B. Shock Absorption: Avoid installing the terminal in a location subject to prolonged and intense vibrations.
- C. Anti-Interference: Keep the terminal away from in-car multimedia and intercommunication systems, NIC devices, to prevent conduction and radiation interference. SMS remote online configuration
The specific format for setting up online via SMS is as follows：
- Edit the SMS content
- <SPBSJ*P:BSJGPS*Q: y.gpstracktech.com:7788*N:17811113333*A：XXX>
- SPBSJ SMS header
- P: BSJGPS password
- y.gpstracktech.com:77888 TCP IP/Port
- N:17811113333 Local number (Up to 15 digits)
- A:XXX APN（Up to 25 digits）
Download the APP [TracePet]
Bind and add the device
When you register an account and log in for the first time, a “Add Tracker” device page will pop up. To add a device again, follow the steps in the following figure (①,②, ③). Binding devices can be automatically searched through “④” or manually entered with the SN number through “⑤”. Confirm to add successfully)
Operating instructions
Press the button for 1 second to turn on the device, press it for 5 seconds to turn it off, and press the button once in the off state to turn up the status light.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for Compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
SAR tests are conducted using standard operating positions accepted by the FCCWith the Wireless Bluetooth pet locator Device transmitting at its highest certifiedpower level in all tested frequency bands, although the SAR is determined at thehighest certified power level, the actual SAR level of the Wireless Bluetooth petlocator Device while operating can be well below the maximum value. Before a new model Wireless Bluetooth pet locator Device is available for sale to the public, itmust be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC. Tests for each Wireless Bluetooth pet locator Device are performed in positions and locations as required by the FCC.
For body-worn operation, this model Wireless Bluetooth pet locator Device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 0 cm from the body. Non-compliance with the above restrictions may result in a violation of RF exposure guidelines.
Documents / Resources
 |
BSJ Technology HW-PET10 Wireless Bluetooth Pet Locator Device [pdf] Instruction Manual HWPET10, 2BNEK-HWPET10, 2BNEKHWPET10, HW-PET10 Wireless Bluetooth Pet Locator Device, HW-PET10, Wireless Bluetooth Pet Locator Device, Bluetooth Pet Locator Device, Pet Locator Device, Locator Device |