XTOOL XTS500 Wireless Diagnostics Module User Manual

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
Once connected, your PC has established a connection with the device.

Žična veza

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Mjere opreza za dijagnozu

Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

Skenirajte QR kod ili posjetite
https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
Raspakujte preuzeto file and run Setup.exe. Follow the installation process.
After installation, restart your PC for changes to take effect.

Kako koristiti
To use J2534 Toolbox:

For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
If not detected, click the Refresh button to try again.
For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
Ensure a stable connection before proceeding with diagnostics.

Trademarks
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

Odricanje od garancija i ograničenje odgovornosti
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

Podrška i servis

Službeno Webstranica: www.xtooltech.com
E-mail: xtoolinplusus@outlook.com

General Introduction

Outlook i portovi

OBDII-16 port: Connect to vehicle’s DLC port.
Nameplate: Show device information.
Type-C Port: Connect the device to diagnosis PC via wire.
Indicator Light: Show device status.

Boja lampice indikatora	Signalna lampica Značenje
Stalno zeleno svjetlo	Uključeno
Trepćuće zeleno svjetlo	Ažuriranje firmvera
Čvrsto plavo svjetlo	Device connected (no communication)
Trepćuće plavo svjetlo	Communicating with the vehicle
Treperi crveno svjetlo	Greška uređaja

Getting Started

Veza vozila

Bežična veza

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
Once the hotspot is connected, your PC has established connection with the device.

Žična veza

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Mjere opreza za dijagnozu

VoltagOpseg na automobilu: +9~+36V DC;
When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
Elektronski upravljački sistemi različitih modela su veoma komplikovani. Ako naiđete na situacije u kojima je nemoguće testirati ili je velika količina testnih podataka nenormalna, možete potražiti ECU vozila i odabrati meni za model na pločici ECU;
Sa ovim uređajem je dozvoljeno koristiti samo kablove koje obezbeđuje XTOOL i koji su dizajnirani za uređaj kako bi se izbeglo oštećenje vozila ili uređaja;
When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

Instalacija

Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
And find “J2534 Toolbox” for the installation pack.
After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

Kako koristiti

The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

Plug in the WiFi Receiver that comes with the VCI box.
Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
When the connection is ready, you are OK to go.

Glavni ekran
When the VCI is connected, you will see this screen:

SN: Shows the SN of the current VCI.
Firmware Version: Shows current firmware version that is installed on the VCI.
Driver Version: Shows current driver version that is installed on the VCI.
J2534 Authorization: Shows the VCI authorization status of current VCI.

Log Record: Turn on/off the J2534 communication logs recording.
Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
You can choose the version first, and click “Upgrade” button on the right to start updates.
DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

Postavke

Click the “Settings” button on the top-right corner and go to the Toolbox settings.
Languages: Click to change language shown on the Toolbox.
Version Number: Check the updates of the Toolbox.
Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
Save Location: This shows the location of the log folder. You can click this to get into the folder.

DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

Povratne informacije

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

Vaša email adresa
Dnevnik files, recorded when the issues happened
Vehicle information (brand, model, MY)
Firmware/Driver version info
A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

Usklađenost sa FCC-om

FCC ID: 2AW3IV01W2

Ovaj uređaj je u skladu sa dijelom 15 FCC pravila. Rad je podložan sljedeća dva uslova:

Ovaj uređaj možda neće uzrokovati štetne smetnje
Ovaj uređaj mora prihvatiti sve primljene smetnje, uključujući smetnje koje mogu uzrokovati neželjeni rad.

Upozorenje
Promjene ili modifikacije koje nije izričito odobrila strana odgovorna za usklađenost mogu poništiti korisnikovo ovlaštenje da koristi opremu.

Napomena
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Preusmjerite ili premjestite prijemnu antenu.
Povećajte razmak između opreme i prijemnika.
Povežite opremu na utičnicu u strujnom kolu različitom od onog na koji je priključen prijemnik.
Za pomoć se obratite prodavaču ili iskusnom radio/TV tehničaru.

Odgovorna strana

Naziv kompanije: FCC US Agent, LLC
Adresa: 3722 Illinois Avenue, Saint Charles, IL, 60174, SAD
Email: Support@FCCUSAgent.com

ISED izjava

IC: 29441-V01W2
Model: XTS500
PMN: V120，XTS500
HVIN: V01W2A

Ovaj uređaj sadrži predajnike/prijemnike koji su u skladu sa kanadskim RSS-ovima izuzetih od licence za inovacije, nauku i ekonomski razvoj. Rad je podložan sljedeća dva uslova:

Ovaj uređaj možda neće uzrokovati smetnje.
Ovaj uređaj mora prihvatiti sve smetnje, uključujući smetnje koje mogu uzrokovati neželjeni rad uređaja.

Izjava o usklađenosti
Ovim putem, Shenzhen XTOOLtech Intelligent Co., Ltd izjavljuje da je ovaj bežični dijagnostički modul u skladu sa osnovnim zahtjevima i drugim relevantnim odredbama Direktive 2014/53/EU. U skladu sa članom 10(2) i članom 10(10), ovaj proizvod je dozvoljen za upotrebu u svim državama članicama EU.

UKCA

Ovim putem, Shenzhen XTOOLtech Intelligent Co., Ltd izjavljuje da ovaj bežični dijagnostički modul zadovoljava sve tehničke propise koji se primjenjuju na proizvod u okviru propisa Ujedinjenog Kraljevstva o radio opremi (SI 2017/1206); propisa Ujedinjenog Kraljevstva o električnoj opremi (sigurnost) (SI 2016/1101); i propisa Ujedinjenog Kraljevstva o elektromagnetskoj kompatibilnosti (SI 2016/1091) te izjavljuje da isti zahtjev nije podnesen nijednom drugom odobrenom tijelu u Ujedinjenom Kraljevstvu.
Shenzhen Xtooltech Intelligent Co., Ltd.
Dodaj: 17&18/F, A2 zgrada, Kreativni grad, Liuxian Avenue, Nanshan District, Shenzhen, Kina
Sjedište Shenzhen Tel: +86 755 2399608
E-mail: marketing@xtooltech.com

FAQs

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

Dokumenti / Resursi

XTOOL XTS500 Wireless Diagnostics Module [pdf] Korisnički priručnik
XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

Reference

Uputstvo za upotrebu

XTOOL XTS500 Wireless Diagnostics Module

Specifikacije

Upute za upotrebu proizvoda