BRESSER 7802580 WIFI Gateway for 5 In 1 and 7 In 1 Sensor Instruction Manual

Q: How do I connect the Gateway El Nino to my smartphone?
- A: To connect the Gateway El Nino to your smartphone, download the dedicated app from the App Store (for iOS) or Google Play Store (for Android). Follow the app’s instructions to pair the device with your smartphone via Wi-Fi.
Q: Can I use the Gateway El Nino without an internet connection?
- A: The Gateway El Nino requires an internet connection to provide real-time weather data and updates. Ensure a stable Wi-Fi connection for optimal performance.
Q: How often should I calibrate the sensors on the Gateway El Nino?
- A: It is recommended to calibrate the sensors annually for accurate weather readings. Follow the instructions in the user manual for sensor calibration.

“`

View Fullscreen

About this user’s manual

This symbol represents a warning. To ensure safe use, always adhere to the instructions described in this documentation. This symbol is followed by a user’s tip.

Precaution & Warning:

1. Validity note
This documentation is valid for the products with the following article numbers: 7002610 Manual version: 0424 Manual designation: Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a Always provide information when requesting service.
2. General Information
About this Instruction Manual These operating instructions are to be considered a component of the device. Read the safety instructions and the instruction manual carefully before using this device. Keep these instruction manual in a safe place for future reference. If the device is sold or passed on, the instruction manual must be passed on to any subsequent owner/user of the product.
DANGER! You will find this symbol before every section of text that deals with the risk of minor to severe injuries resulting from improper use.
ATTENTION! You will find this symbol in front of every section of text which deals with the risk of damage to property or the environment.
3. General Warnings
DANGER! This device contains electronic components which operate via a power source (power supply and/or batteries). Only use the device as described in the manual, or you run the risk of an electric shock.
Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. If necessary, wear adequate gloves for protection.
ATTENTION! Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary. Do not expose the device to temperatures above 60°C.
Do not expose the device to high temperatures. Use only the supplied power supply or the recommended batteries. Do not short-circuit the device or batteries or throw them into a fire! Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

34
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 34

22.05.2024 09:02:53

Introduction

Thank you for selecting WI-FI weather station gateway. This gateway gathers and automatically uploads accurate weather data to Weather Underground, ProWeatherLive, Weathercloud website and 3rd partly weather platform which allow you to access and upload your weather data freely. This gateway allow you to establish your own sensor array system by using an exclusive app for easy setup. The weather data will be transmitted to the gateway through wireless radio frequency, allow you to continually monitor the local weather conditions. This system able to support a 7-in-1 or 5-in1 optional wireless sensor, up to 7 thermo-hygro optional sensor(s), 7 water leak optional sensor(s) and other optional sensors which include, lightning, PM2.5/10, CO2, HCHO/VOC and CO sensors, this system is truly a remarkably personal professional weather station for your own backyard.

Quick start

The following Quick Start Guide provides the necessary steps to install and operate the weather station, and upload to the internet, along with references to the pertinent sections.

Step Description

Section

1 Power up your gateway

4.3

2 Synchronizing sensor(s) to gateway

3 Install you setup app: WSLink

7.1

4 Add you gateway to WSLink

7.3

5 Configure W-Fl connection and other settings of your gateway with 7.3.1 – 7.5

WSLink

6 Register your gateway at weather server(s) to obtain station lD and 8

key

3. Package contents You can find the follow items in the box.

Wi-Fi weather station gateway

USB power cable

User manual

35
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 35

22.05.2024 09:02:53

Gateway overview

4.1 Gateway introduction

5
AA-11-BB-XX-YY-ZZ

7 1

No. Key / Part name

Description

1 SENSOR indicator Blink rapidly: Sensor to gateway pairing in process.

On (steady): Sensor(s) paired to gateway is in normal operation.

Blink slowly: Gateway failed to receive data from paired sensor(s).

2 [ SENSOR ] 3 [ WI-FI ]

Hold 2 seconds to start/exit sensor synchronization (pairing). · Press to synchronize time and upload data to connected server.

· Hold 6 seconds to enter/exit Access Point (AP) mode.

4 WI-FI indicator

Blink rapidly: Gateway in Access Point (AP) mode

On (steady): Gateway connected to Wi-Fi network.

Blink slowly: Gateway trying to connect to Wi-Fi network.

5 Wall mount hole

6 [ RESET ]

· Press the RESET-button to reset your gateway.

· Hold the RESET-button 8 seconds to factory reset your gateway.

7 Mac address

8 USB type-C socket for power supply

4.2 LED indicator SENSOR indicator:
· Blink rapidly: Sensor to gateway pairing mode. · On (steady): One or more sensors are paired to gateway. The indicator will blink once each time
when one package of data is received from a sensor(s) · Blink slowly: One or more sensors has lost communication with gateway.
WI-FI indicator: · Blink rapidly: Unit is in factory Access Point (AP) mode state. It has never been configured for router
and weather server. · On: Connected to WI-FI network, and able to upload data to weather server(s) · Blink slowly: Unit is trying to connect to Wi-Fi network, or failed to publish data to any of the weather
server(s).

4.3 Power up your gateway 1. Plug your USB cable type-C plug to your gateway 2. Plug in the USB cable type-A plug to USB type A power outlet or adaptor (optional) 3. Once your gateway is power up, all the SENSOR and WI-FI indicator will fast flashing 4. Your gateway will start AP mode and sensor synchronization mode automatically
5. Registering with weather server platforms This gateway can upload weather data to below weather server through WI-FI network:
· ProWeatherLive (https://proweatherlive.net) · Weather Underground (https://www.wunderground.com) · Weathercloud (https://weathercloud.net)
You can follow the guideline on corresponding weather server web page to register the account and setup your device in the their platforms.
Once you get the station ID and key from the platform, you can follow the steps in below to complete the weather server configuration.
For ProWeatherLive, refer to: Section 7.4.4 (1) For Weather Underground, refer to: Section 7.4.4 (2) For Weathercloud, refer to: Section 7.4.4 (3)
6. Synchronizing sensor(s) to gateway The gateway will automatically activates its pairing mode for sensor(s) to be synchronized to it immediately after power-up. User may also manually enter / exit the synchronization mode by press and hold [SENSOR] for 2 seconds.
Rapid blinking

1. Press and hold [ SENSOR ] for 2 seconds, until LED indicator start blinking rapidly. 2. Insert batteries into the sensor(s), or press [ RESET ] on the sensor(s). 3. The sensor LED indicator will pause momentarily when a sensor is paired to it, then resumes
blinking rapidly. User may press and hold [ SENSOR ] for 2 seconds to exit synchronization mode*. *Gateway will exit synchronization mode automatically after 5 minutes.

6.1 Sensor list This gateway can connect up to 20 optional wireless sensors. Some of these sensors are multichannel. Each sensor must be set to a different channel. Before inserting the batteries, choose the channel inside the battery compartment. For their operation, please refer to the manuals that come along with the products.
37

Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 37

22.05.2024 09:02:53

6.1.1 Outdoor professional sensor array

Model

Sensor(s) supported

Description 5-in-1 professional sensor

7802580

Sensor data: Outdoor temperature, outdoor humidity, wind speed, wind direction and rain data

Image

7803300 7803200 7803510

7-in-1 professional sensor
Sensor data: Outdoor temperature, outdoor humidity, wind speed, wind direction, rain data, UV and light intensity

1 sensor

7-in-1 professional sensor with built in solar panel
Sensor data: Outdoor temperature, outdoor humidity, wind speed, wind direction, rain data, UV and light intensity
7-in-1 professional sensor with built in tiltable solar panel and Capacitor with extra high capacitance.
Sensor data: Outdoor temperature, outdoor humidity, wind speed, wind direction, rain data, UV and light intensity

38
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 38

22.05.2024 09:02:54

6.1.2 Thermo-hygro sensors

Model

Sensor(s) supported

Description Thermo-Hygro sensor

7009971

Sensor data: CH7~1 temperature and humidity

7009972

Soil Moisture and Temperature Sensor
Sensor data: CH7~1 soil moisture and temperature Up to 7 sensors

Image
868MHz SOIL SENSOR

7009973

Pool Sensor
Sensor data: CH7~1 water temperature

6.1.3 Leakage sensor

Model
7009975
1

Sensor(s) supported

Description Water leak sensor

Sensor data: Up to 7 sensors CH7~1 water leak status

6.1.4 Lightning sensor

Model

Sensor(s) supported

7009976

1 sensor

Description Lightning sensor
Sensor data: Lightning strike and distance

Image
868MHz WATER LEAK SENSOR
Image

39
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 39

22.05.2024 09:02:54

6.1.5 Air quality sensors

Model

Sensor(s) supported

Description PM2.5 / 10 sensor

7009970

Sensor data: PM 2.5 and PM10 concentration

Image
868MHz AIR QUALITY SENSOR
PM 2.5 / PM 10

7009977

1 sensor

CO2 sensor
Sensor data: CO2 concentration

CO2 SENSO R

HCHO with VOC sensor

7009978

Sensor data: HCHO concentration and VOC level

For air quality sensors pairing, you can assign the sensors in any channel. Your gateway support to display one channel of each of air quality sensor.

6.2 Recommendation for best wireless communication
Effective wireless communication is susceptible to noise interference in the environment, and distance and barriers between the sensor transmitter and your gateway.

1. Electromagnetic interference (EMI) these may be generated by machinery, appliances, lighting, dimmers and computers, etc. So please keep your gateway 1 or 2 meters away from these items.
2. Radio-frequency interference (RFI) if you have other devices operating on 868 / 915 / 917 MHz, you might experience communication intermittent. Please re-located your transmitter or gateway to avoid signal intermittent problem.
3. Distance – Path loss occurs naturally with distance. This device is rated to 150m (450 feet) by line of sight (in interference free environment and without barriers). However, typically you will get 30m (100 feet) maximum in real life installation, which includes passing through barriers.
4. Barriers – Radio signal are blocked by metal barriers such as aluminum cladding. Please align the sensor array and gateway to get them in clear line of sight through window if you have metal cladding.

The table below show a typical level of reduction in signal strength each time the signal passed through these building materials

Materials
Glass (untreated) Wood Plasterboard / drywall Brick Foil insulation Concrete wall Aluminum siding Metal wall

Signal strength reduction
10 ~ 20% 10 ~ 30% 20 ~ 40% 30 ~ 50% 60 ~ 70% 80 ~ 90% 100% 100%

Remarks: RF signal reduction for reference

Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 40

22.05.2024 09:02:54

Connect gateway to Wi-Fi network

7.1 Download WSLink configuration app

WSLink To connect gateway to WI-FI, you need to download the “WSLink” configuration app from one of the following links by scanning the QR code or search “WSLink” in App Store or Google Play.

App Store

Google Play

WSLink app is required for your gateway to connect to WI-FI and Internet, setup weather server, perform sensor calibration and firmware update.

Note:
– WSLink app is only for configuration. It is not used to remotely view your weather data. – WSLink app may subject to change and update

7.2 Gateway in Access Point (AP) broadcast mode When you power up your gateway for the first time, your gateway WI-FI status indicator will be flashing to signify that it has entered AP (Access Point) mode and is ready for WI-FI settings. User may also manually press and hold the [ WI-FI ] key for 6 seconds to enter/exit AP mode
manually.

AP mode of your gateway Press and hold the [ WI-FI ] button for server until the LED indicator starts blinking rapidly.

41
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 41

22.05.2024 09:02:54

7.3 Add your gateway to WSLink Open the WSLink app and follow the steps below to add your gateway to WSLink.

YOUR DEVICE

CONNECT DEVICE

Wi-Fi Wi-Fi

Add Device

Check if the console is in AP mode (AP mode screen)
OTHERWISE

My Router
Connected
PWS-XXYYZZ
No encrypted
Room Router
Encrypted
John
No encrypted

(a) Your Device page Tap “Add Device” icon.

Press & hold WI-FI button for 6 sec or turn on AP mode in setup menu
of the device
Operation completed
Confirm
(b) Ensure the gateway is in AP mode and check the “Operation completed” box, then tap “Confirm” to go to system WI-FI network page of your smart phone.

(c) Select the gateway WI-FI network name (the name always begin with PWS-) to connect your smart phone to the console. Then tap back to WSLink app.
DEVICE ADDED
PWS-XXYYZZ

Next section: Setup new gateway with WSLink

Next
(d) Once the gateway is added to WSLink, the console icon will appear on your device list. Tap the icon to continue the setup.
Note: – For first time connection of smartphone to your gateway Wi-Fi network, you need to acknowledge any “no
internet connection” notice when being prompted. – If your smart phone cannot connect to your gateway, please turn off the mobile data / network in your smart
phone and try again.
42

Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 42

22.05.2024 09:02:55

7.3.1 Setup gateway in WSLink The app will follow the steps below to guide you through the setup.

Wi-Fi

Edit device

Weather server

Network My Router Password
Other Wi-Fi network
Next
(e) Wi-Fi page Network: select Wi-Fi network (router SSID) for connection. Password: enter Wi-Fi password. Other Wi-Fi network: setup tp hidden Wi-Fi network. Next: go to ,,edit Device” page.

Device name PWS-XXYYZZ

General settings Time server Time zone Daylight saving time Hemisphere LED indicators Data reset

time.nist.gov +1:00 Auto North
Always on

MAC

AA:11:BB:XX:YY:ZZ Next

(f) Edit device page Please refer to section 7.4.2 for more details Edit device. Next: go to ,,Weataher server” page.

ProWeatherLive Weather Underground Weathercloud Other Server

Note

Next
(g) Weather server page Please refer to section 7.4.4 for more details Weather server. Next: go to ,,Settings” page.

PWS-XXYYZZ
(j) Delete your gateway To remove device from the app, swipe the gateway icon left and tap the bin.

YOUR DEVICE
PWS-XXYYZZ AAdddd DDeevviiccee

Settings
Wi-Fi Edit device Sensor Weather server Calibration Firmware

(i) Your Device page Your setup is now completed. You can tap the icon and follow the procedure to do the gateway settings anytime if necessary.

Confirm & Exit
(h) Settings page This is main page of the gateway, you can enter different setup page to setup your gateway. Once you complete the setup, tap ,,Confirm & Exit” to exit AP mode.

43
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 43

22.05.2024 09:02:56

7.4 Settings overview

Settings
Wi-Fi Edit device Sensor Weather server Calibration Firmware

7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.4.6

Confirm & Exit

Note: For Wi-Fi and Firmware, user may be prompted to set the gateway into Access Point (AP) mode.

7.4.1 Wi-Fi
– Network: Select router (SSID) for connection – Password: Enter the router’s password – Other Wi-Fi network: Tap to setup the connection for other hidden Wi-Fi
network.

Wi-Fi Network My Router Password

Other Wi-Fi network Next

44
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 44

22.05.2024 09:02:56

7.4.2 Edit device
– Device name: Able to change your gateway’s name in app device list.
– Time server: Set time server for time synchronization. – Time zone: Select the time zone where your gateway is located. – Daylight saving time: to select Auto / On / Off mode
· Auto mode is to adjust the daylight saving time automatically based on time zone entered.
· On mode is to add one hour on current default time. · Off mode is to completely turn off the DST function. – Hemisphere: Select hemisphere where your gateway located. – LED indicators: Set gateway indicator mode (Always On / Off). – Data reset: Clear your gateway data.
Note: · Current time and date information are important for rain calculation,
may sure the time zone is correct. · During installation of the wireless 7-in-1 or 5-in-1 sensor, the sensors
were likely to be triggered, resulting in erroneous rainfall and wind measurements. After the installation, user may clear out all the erroneous data from your gateway. Simply tap the Data reset to clear your gateway data.

Edit device

Device name PWS-XXYYZZ

General settings Time server Time zone Daylight saving time Hemisphere LED indicators Data reset

time.nist.gov +1:00 Auto North
Always on

MAC

AA:11:BB:XX:YY:ZZ

7.4.3 Sensor status
– Type: The connected sensor type (Section 6.1 Sensor list) – ID: The ID of the sensor(s) that connected to your gateway – Status: The signal strength and battery status of the connected
sensor(s)
Signal strength

Type Outdoor CH1 CH2

ID 00512307 00512102 00F12303

Status

No connection No signal

Weak signal Good signal

Battery status If the low battery indicator ” ” or ” ” appear on sensor row, it indicates that the current sensor battery power is low respectively. Please replace with new batteries.

Remove sensor In order to remove the sensor(s) connection from your gateway, swipe the sensor icon left and tap the bin.

CH3 CH4 CH5 CH6 CH7 PM2.5/10 HCHO/VOC CO2 CO Lightning

-0A112305 00F12303 01A12603 70C12819 0B512D06 AB51FD01 FB5D2D02 0B572DF4 B0F123E3

Outdoor

00512307

1 Water leak 2 Water leak 3 Water leak

90A1220A 0AF1450D 01F12300

45
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 45

22.05.2024 09:02:57

7.4.4 Weather server setting The setup page of 4 weather servers: ProWeatherLive, Weather Underground, Weathercloud and customized server.
Weather server

ProWeatherLive Weather Underground Weathercloud Other Server

Note

(1) (2) (3) (4)

(1) Upload your weather data to ProWeatherLive 1. Register an account and general station ID and key at
proweatherlive.net (refer to section 8.1) 2. Enter the station ID and station key obtained from
proweatherlive.net into this panel 3. Enable the upload 4. Tap “Save”

Weather server

ProWeatherLive Station ID PWL2345678
2
Station key
******

MAC

AA:11:BB:XX:YY:ZZ

Upload

*You need to first register your device
at ProWeatherLive (proweatherlive.net). Then enter the Station ID and Key obtained and tap “Save”.

Save

46
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 46

22.05.2024 09:02:57

(2) Upload your weather data to Weather Underground
1. Register an account and general station ID and key at wunderground.com (refer to section 8.2)
2. Enter the station ID and station key obtained from WUnderground.com into this panel
3. Enable the upload 4. Tap “Save”

Weather server
Weather Underground Station ID I12345
2
Station key ******

Upload

(3) Upload your weather data to Weathercloud
1. Register an account and general station ID and key at Weathercloud.net (refer to section 8.3)
2. Enter the station ID and station key obtained from Weathercloud.net into this panel
3. Enable the upload 4. Tap “Save”

*You need to first register your device at
Weather Underground (wunderground.com). Then enter the Station ID and Key obtained and tap “Save”.

Save

Weather server

Weathercloud Station ID I123EAQ5eR359Ew2
2
Station key ******

Upload

*You need to first register your device
at Weathercloud (weathercloud.net). Then enter the Station ID and Key
obtained and tap “Save”.

Save

47
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 47

22.05.2024 09:02:57

(4) Upload to customized server
1. Prepare your customized server based on WUnderground or WSLink API
2. Enter the URL address, Station ID and Station key of the customized server
3. Select upload interval and API type (e.g. WSLink API) 4. Enable the upload 5. Tap “Save”

Weather server Other Server URL
Station ID

Station key

Upload interval 1 minute
API type WSLink API
WSLink API

MAC Upload

AA: 11: BB: XX: YY: ZZ Save

After you selected the WSLink API type, a WSLink API download button will be appeared under API type section, you may tap the icon to obtain the full set of WSLink data upload API document.

7.4.5 Calibration Your gateway is able to calibrate the readings of the sensor(s) in WSLink APP

Settings
Wi-Fi Edit device Sensor Weather server Calibration Firmware
Confirm & Exit
(a) Settings page At the settings page, tap “Calibration”.

Calibration Indoor (Display Console) Outdoor (Sensor Array) CH1 CH2 CH3 CH4 CH5 CH6 CH7 Other sensors
Save

Unit Change unit Indoor section Outdoor section
CH section for optional thermo-hygro sensor(s)
Section for other optional sensor(s)

(b) Calibration page 1. Tap on the section where calibration is needed. 2. Tap “Unit” to change the unit if necessary 3. Tap “Save”.

Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 48

22.05.2024 09:02:57

Calibration parameters

Section Indoor

Parameters

Type of Calibration

Temperature

Offset

Humidity

Offset

Absolute pressure Offset

Relative pressure Offset

Outdoor (Optional)

Temperature WBGT Humidity Wind direction Wind speed Rain UVI Light

Offset Offset Offset Offset Gain
Gain
Gain
Gain

CH1~7

Temperature

Thermo-hygro

(Optional) Humidity

Offset Offset

Default value 0 0 0
0
0 0 0 0 1 1 1 1
0
0

Setting range
±20°C ±20 % ±560hPa (±16.54inHg or ±420mmHg) ±20°C ±20°C ±20 % ±90° x 0.5 ~1.5 x 0.5 ~1.5 x 0.01 ~ 10.0 x 0.01 ~ 10.0
±20°C
±20 %

Typical calibration source
Red spirit or mercury thermometer Sling psychrometer Calibrated laboratory grade barometer
Local airport
Red spirit or mercury thermometer Calibrated laboratory grade WBGT meter Sling psychrometer GPS or Compass Calibrated laboratory grade wind meter Sight glass rain gauge with meter Calibrated laboratory grade UV meter Calibrated laboratory grade solar radiation sensor Red spirit or mercury thermometer
Sling psychrometer

PM2.5 value

Offset

±99g/m³

Calibrated laboratory grade PM2.5 sensor

Others

PM10 value

Offset

±99g/m³

Calibrated laboratory grade PM10 sensor

sensors

HCHO value

Offset

±500ppb

Calibrated laboratory grade HCHO sensor

(Optional)

CO2 value

Offset

±500ppm

Calibrated laboratory grade CO2 sensor

CO value

Offset

±200ppm

Calibrated laboratory grade CO sensor

Note:
– Calibration of most parameter is not required, with the exception of relative pressure, which must be calibrated to sea-level to account for altitude effects.
– For temperature and pressure, the app will always calculate & convert the calibration value in °C and hPa respectively.

7.4.6 Firmware update
You can check and update your gateway firmware in AP mode. Once you entered AP mode, follow the below step to check the firmware version of your gateway.

Settings

Firmware

Wi-Fi Edit device Sensor Weather server Calibration Firmware

Firmware version

1.00 New Firmware 1.01 available

Confirm & Exit
(a) Settings page At the settings page, tap “Firmware”.

Update
(b) Your current firmware version will be shown. Tap “Update” if new firmware is available (indicated by a red dot)

49
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 49

22.05.2024 09:02:57

While the updating is in process, the WI-FI indicator will be flashing rapidly. Your gateway will restart once the update is completed.

Fast Flashing
Important note:
– Please keep connecting the power during the firmware update process. – Please make sure your gateway WI-FI connection is stable. – When the update process start, do not operate your gateway until the update is finished. – Settings and data maybe lost during update. – During firmware update, your gateway will stop upload data to the cloud server. It will reconnect
to your WI-FI network and upload the data again once the firmware update succeed. If your gateway cannot connect to your router, please enter the SETUP page to setup again. – Firmware update process have potential risk, which cannot guarantee 100% success. If the update fail, please redo the above step to update again.

7.5 API for customized weather server
Customer can either choose WUnderground API or WSLink API to upload the weather data to their own weather server. WUnderground API covers the basic parameters shown on Weather Underground, user may select WSLink API for full set of upload protocols that include all the parameters which connected to your gateway, including those connected optional sensors.

Weather server Other Server URL
Station ID

Station key

Upload interval 1 minute
API type WSLink API
WSLink API

MAC Upload

AA: 11: BB: XX: YY: ZZ Save

50
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 50

22.05.2024 09:02:57

7.6 STA mode operation
Provided your smart phone and gateway are both connected under the same Wi-Fi network, you may directly access your gateway’s settings.

YOUR DEVICE

Settings

PWS-XXYYZZ Add Device

Wi-Fi Edit device Sensor Weather server Calibration Firmware

Confirm & Exit

(a) Your Device page Ensure your gateway and smart phone are connected in the same network, then tap your console icon to enter settings page.

(b) Settings page (under STA mode) User may tap to enter different setup page, except Wi-Fi and Firmware. To exit settings, tap “Confirm & Exit”.

Registering with weather server platforms

The display console can upload /download weather data to ProWeatherLive (PWL), WUnderground and / or Weathercloud through WI-FI router, you can follow the step below to register the account and setup your device in the following platforms.
8.1 ProWeatherLive.net (PWL) *** This is best done on a computer desktop or laptop*** 1. In https://proweatherlive.net click the “Create Your Account” then follow the instructions to
create your account.

Note: – You can find the create account step in https://proweatherlive.net/help – ProWeatherLive (PWL) website and app are subject to change without prior notice.
51
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 51

22.05.2024 09:02:58

2. Log in the ProWeatherLive and then click the “Edit Devices” in the pull down menu.
Dashboard Account Edit Devices Unit & Display Alert Setting Weather Server Data Export Help FAQ Log Out
3. In “Edit Devices” page, click the ” +Add ” on the top right corner to create a new device, it will generate the Station ID and key instantly. Make a note of this and then click ” FINISH ” to create the station tab.

4. Click the ” Edit ” on the top right corner of the station tab.

5. Enter the “Device name”, “Device MAC address”, “Elevation”, “Latitude”, “Longitude” and select your time zone in the station tab, then click ” Confirm ” to save the setting.

Note: – The device MAC address can be found on the backside of the console.

52
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 52

22.05.2024 09:03:00

AA:11:BB:XX:YY:ZZ
Device MAC address – The weather forecast and weather condition will be based on the Latitudes and Longitudes entered,
which are also used for calculations of sunrise, sunset, moon rise and moon set times. – Enter a negative sign for Latitudes or Longitudes when it’s South or West respectively.
For example: 33.8682 South is “-33.8682” ; 74.3413 West is “-74.3413”
8.2 WeatherUnderground.com (WU) *** This is best done on a computer desktop or laptop*** 1. In https://www.wunderground.com click the “Join” on the top right corner to open the
registration page. Follow the instructions to create your account.
2. Once you have created your account and completed the Email validation, please go back to the WUndergound web page to login. Then, click “My Profile” on the top to open the dropdown menu and click “My Weather Station”.
3. In “My Weather Station” page bottom, click the “Add New Device” to add your device. 4. In step “Select a Device Type”, choose “Other” in the list, then press “Next”.

53
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 53

22.05.2024 09:03:00

5. In step “Set Device Name & Location”, select your location on the map, then press “Next”.

6. Follow their instruction to enter your station information, in the Step “Tell Us More About Your Device”, (1) enter a Name for your weather station. (2) fill in the other information (3) select “I Accept” to accept Weather underground’s privacy terms, (4) click “Next” to create your station
ID and key.

(1)

(2)

(3)
(4)
7. Jot down Your “Station ID” and “Station key” for the further setup step.

54
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 54

22.05.2024 09:03:01

8.3 Weathercloud (WC) *** This is best done on a computer desktop or laptop*** 1. In https://weathercloud.net enter your information in “Join us today” section, then follow the
instructions to create your account.
2. Sign in Weathercloud and then you will go the “Devices” page, click “+ New” to create new device.
3. Enter all the information in Create new device page, for the Model* selection box select the “W100 Series” under “CCL” section. For the Link type* selection box select the “SETTINGS”, Once you have completed, click Create.

55
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 55

22.05.2024 09:03:02

4. Jot down your ID and key for the further setup step.

View weather server live data & operation

9.1 Viewing your weather data in WUnderground
Login your account. To view your weather station live data in a web browser (PC or mobile version), please visit http:// www.wunderground.com, and then enter your “Station ID” in the searching box. Your weather data will show up on the next page. You can also login your account to view and download the recorded data of your weather station.

Another way to view your station is use the web browser URL bar, type below in the URL bar: https://www.wunderground.com/dashboard/pws/XXXX
Then replace the XXXX by your Weather underground station ID to view your station live data.

9.2 Viewing your weather data in Weathercloud

1. To view your weather station live data in a web browser (PC or mobile version), please visit https://weathercloud.net and sign in your own account.

2. Click the

icon inside the

pull down menu of your station.

56
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 56

22.05.2024 09:03:03

3. Click “Current”, “Wind”, “Evolution” or “Inside” icon to view the live data of your weather station.

9.3 Viewing weather server data via WSLink app With WSLink app, user may tap the Wunderground or Weathercloud web page shortcut icon in
“Your Device” page to directly access live weather data on their dashboard respectively.

YOUR DEVICE
PWS-ZZZZZZ

ProWeatherLive shortcut WUnderground shortcut Weathercloud shortcut

Add Device

10. Reset and factory reset
To reset your gateway and start again, press the [ RESET ] key once. To resume factory settings and remove all data, press and hold the [ RESET ] key for 6 seconds.

57
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 57

22.05.2024 09:03:04

11. Troubleshoot

Problems

Solution

SENSOR indicator slow blinking Make sure your gateway is placed away from other

(One or more sensors failed to electronic appliances that may interference with the wireless

connect gateway)

communication (TVs, computers, microwaves).

1. Make sure the sensor(s) is within the transmission range.

Optional wireless sensor(s) is intermittent or no connection

2. Check the sensor(s) battery status in WSLink. 3. If it still does not work, reset the sensor and pair with the
gateway again

1. Make sure your gateway and smart phone are connect to

the same WI-FI network.

Cannot use the STA mode for setup

2. Make sure your gateway WI-FI signal icon are always on. 3. Make sure the location function of your smart phone is
enabled.

4. Ensure your APP are the latest version. 1. Check the WI-FI icon on the display, it should be on if
connectivity is successful.

WI-FI indicator Blinking

2. Make sure the WI-FI settings (router’s name, security type,

(No WI-FI connection, Searching password) are correct.

WI-FI network or connection not 3. Make sure you connect to 2.4G band of the WI-FI network

stable)

(5G not supported)

Data not reporting to weather server
Indoor temperature reading too high in the day time
Gateway no response or malfunction

4. Ensure the customized URL, station ID and/or Key are correct.
1. Make sure the WI-FI connection of your gateway is good.
2. Ensure your Station ID and Station Key are correct. Ensure that the gateway is placed away from heat generating sources You can follow the below step to fix: 1. Unplug the USB power socket.

WI-FI indicator intermittent
flashing (Firmware update fail or error)

2. After 1 minute, plug the USB power socket again. Press and hold the [ SENSOR ] and [ WI-FI ] key at the same time with 10 seconds to back to original version, then redo the update procedure again.

58
Manual_7002610_WIFI-Gateway-Sensor_de-en_BRESSER_v042024a.indb 58

22.05.2024 09:03:04

12. Specifications

General specification

Dimensions (W x H x D)

45 x 110 x 41mm (1.8 x 4.3 x 1.6 in)

Weight

74g

Main power

DC 5V, 1A (USB type C input)

Operating temperature range -5°C ~ 50°C

Operating Humidity range

10 ~ 90% RH

RF frequency (Depend on country version)

868Mhz (EU or UK version)

Time related function specification

Time synchronize method

Internet time server

WI-FI communication specification

Standard

802.11 b/g/n

Operating frequency :

2.4GHz

Setup app

APP name

WSLink 1.5 or later

Support platform

Android 8.0 smart phone or latest iOS 9.3 (iPhone) or latest

Support weather server

Weather Underground

https://www.wunderground.com

Weather cloud

https://weathercloud.net

ProWeatherLive

https://proweatherlive.net

Barometer

Barometer unit

hPa, inHg and mmHg

Accuracy

(700 ~ 1100hPa ± 5hPa) / (540 ~ 696hPa ± 8hPa) (20.67 ~ 32.48inHg ± 0.15inHg) / (15.95 ~ 20.55inHg ± 0.24inHg) (525 ~ 825mmHg ± 3.8mmHg) / (405 ~ 522mmHg ± 6mmHg) Typical at 25°C (77°F)

Resolution

1 hPa / inHg is 2 decimal place / mmHg is 1 decimal place

Indoor temperature

Temperature unit Accuracy Resolution

°C and °F 0°C ± 2°C (32°F ± 3.6°F) >0 °C ± 1°C (>32 °F ± 1.8°F)
°C / °F (1 decimal place)

Indoor humidity

Humidity unit Accuracy

%
1 ~ 9% RH ± 8% RH @ 25°C (77°F) 10 ~ 90% RH ± 5% RH @ 25°C (77°F) 91 ~ 99% RH ± 8% RH @ 25°C (77°F)

Resolution

13. DISPOSAL

If you pass on or dispose of the station, you should delete the stored WLAN data to prevent unauthorised access to your WLAN.
Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! As per Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
14. CE Declaration of Conformity Hereby, Bresser GmbH declares that the equipment type with part number: 7002610 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: http://www.bresser.de/download/7002610/CE/7002610_CE.pdf

WARRANTY & SERVICE

The regular warranty period is 2 years and begins on the day of purchase. To benefit from an extended voluntary warranty period as stated on the gift box, registration on our website is required.
You can consult the full warranty terms as well as information on extending the warranty period and details of our services at www.bresser.de/warranty_terms.

Service

E-Mail:

service@bresser.de

Telefon*: +49 28 72 80 74 210

E-Mail:

info@bresserbenelux.nl

Telefoon*: +31 528 23 24 76

GB IE

Please contact the service centre first for any questions regarding the product or claims,
preferably by e-mail.

E-Mail:

service@bresseruk.com

Telephone*: +44 1342 837 098

BRESSER UK Ltd.
Suite 3G, Eden House Enterprise Way Edenbridge, Kent TN8 6HF Great Britain
*Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Documents / Resources

BRESSER 7802580 WIFI Gateway for 5 In 1 and 7 In 1 Sensor [pdf] Instruction Manual
7802580 WIFI Gateway for 5 In 1 and 7 In 1 Sensor, 7802580, WIFI Gateway for 5 In 1 and 7 In 1 Sensor, 5 In 1 and 7 In 1 Sensor, Sensor

References

User Manual

BRESSER 7802580 WIFI Gateway for 5 In 1 and 7 In 1 Sensor

Product Information

Product Usage Instructions

FAQ

Introduction

Quick start

Gateway overview

Connect gateway to Wi-Fi network

Registering with weather server platforms

View weather server live data & operation

WARRANTY & SERVICE

Documents / Resources

References

Leave a comment

Cancel reply